Page 1
Form# 43553-01
20090515
©2009 Hunter Fan Co.
English Español
Four Light FixtureFour Light FixtureFour Light Fixture
Owner’s Guide and Installation Manual
Manual De Propietario
Page 2
2
43553-01 • 05/15/09 • Hunter Fan Company
Table Of Contents
1 • Installing the Light xture on Fans With
Removable Switch Housings .......4
2 • Installing the Light xture on Fans With
Non-Removable Switch Housings..6
3 • Installing the Light xture on the Hunter
Originals . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 • Installing Bulbs and Shades .........9
5 • Troubleshooting....................10
© 2009 Hunter Fan Company
Your new Hunter® light xture is an addition to your home or oce
that will provide comfort and performance for many years. is
installation and operation manual gives you complete instructions for
installing and operating your light xture.
We are proud of our work. We appreciate the opportunity to supply
you with the best products available anywhere in the world.
Before installing your light xture, for your records and warranty
assistance, record information from the carton and Hunter nameplate
label.
Cautions and Warnings
• READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING
INSTALLATION. SAVE THESE INSTRUCTIONS.
• Use only Hunter replacement parts.
• To reduce the risk of personal injury, install this light xture only on
Hunter® fan types A through Z. Note: e fan type can be found on
the ceiling fan package or on the nameplate label located on top of
the motor housing of the ceiling fan.
• To avoid possible electrical shock, before installing light xtures,
disconnect the power by turning o the circuit breakers both to
the outlet box and to its associated wall switch location. If you
cannot lock the circuit breakers in the o position, securely fasten a
prominent warning device, such as a tag, to the service panel.
• Connect house wiring to the fan before attaching the light xture to
the fan.
• All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualied electrician.
Welcome
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Page 3
3
43553-01 • 05/15/09 • Hunter Fan Company
Installation Methods of Hunter® Ceiling Fans Type A-Z
Removable Switch Housing
Non-removable Switch Housing
e Hunter Original
Your ® light xture can be installed in one of three
ways, depending on the type of switch housing. e steps
in this manual include instructions for all three installation
methods: Fans with removeable switch housings, fans
with non-removeable switch housings, and
e Hunter Original.
Preparing the Light Fixture
1. Shades are not included with this light xture. Be sure to
purchase shades for your light xture before installing
this light xture.
2. Disconnect power by turning o the circuit breakers
both to the outlet box and to its associated wall switch
location.
Page 4
4
43553-01 • 05/15/09 • Hunter Fan Company
1. Unscrew the three screws from the upper switch housing. Disconnect
the 9-pin plug connectors. Remove the lower switch housing.
2. Push the plug button from inside the lower switch housing to remove
the plug button and switch housing cap.
NOTE: Save the plug button and switch housing cap should you
choose to remove the light xture in the future.
3. Feed the two wires from the light xture through the center hole in
the lower switch housing.
4. Screw the threaded rod of the light xture into the center of the lower
switch housing until you feel resistance. Unscrew the light xture
slightly until the holes of the light xture are aligned with the holes in
the lower switch housing.
5. Finish attaching the light xture to the lower switch housing using the
two attachment screws included. Securely tighten the two screws.
6. Install the nut and washer inside the lower switch housing onto the
threaded rod from the upper light housing.
Removable Switch Housing
9-Pin Plug
Connector
Lower Switch
Housing
Plug Button
Screw
Steps 1-2
Lower
Switch
Housing
Light
Fixture
WARNING: Improper installation could
cause the light xture to fall, or result in
electrical shock or personal injury.
Steps 3-6
Washer
Nut
Attachment
Screws
Threaded
Rod
1 • Installing the Light fixture on Fans With Removable Switch Housings
Page 5
5
43553-01 • 05/15/09 • Hunter Fan Company
1 • Installing the Light fixture on Fans With Removable Switch Housing (Continued)
7. Remove the wire connectors from the two wires in the switch
housing labeled “Connect Light Here” or “For Light Use.”
To connect the wires, hold the bare metal leads together
and place a wire connector over them, then twist the wire
connector clockwise until tight.
Connect the black wire with a white stripe from the switch
housing to the black wire from the light xture. Connect the
white wire from the switch housing to the white wire from the
light xture. Secure all wire connections using wire connectors.
CAUTION: Be sure no bare metal wires or wire strands are
visible after making the connections.
8. Reconnect the 9-pin plug connector.
9. Reinstall screws to reattach the lower switch housing to the
upper switch housing.
10. Go to the instructions for Installing Bulbs, and Shades.
Wires
and Wire
connectors
Step 7
Plug
Connector
Lower Switch
Housing
Housing
Assembly Screw
Plug
Connector
Detail
Steps 8-9
Page 6
6
43553-01 • 05/15/09 • Hunter Fan Company
1. Uninstall the two attachment screws from the switch housing cover.
2. Remove the plug or screw from the center of the switch housing cover.
3. read the switch housing cover onto the light xture. Align the screw
holes in the light xture with the screw holes in the switch housing cover.
4. Use the two attachment screws removed from the lower switch housing
and the lock washers on the red tag of the light xture. Install the screws
into the light xture and the housing. Securely tighten the two screws.
5. Remove the wire connectors from the two wires in the switch housing
labeled “Connect Light Here” or “For Light Use.” One wire is white and the
other wire is black with a white stripe.
6. Feed the two wires from the switch housing through the threaded rod in
the upper light housing.
7. To connect the wires, hold the bare metal leads together and place a wire
connector over them, then twist the wire connector clockwise until tight.
Connect the black wire with a white stripe from the switch housing to
the black wire from the light xture. Connect the white wire from the
switch housing to the white wire from the light xture. Secure all wire
connections using wire connectors.
8. Align the threaded screw holes in the switch housing cover with the
threaded holes in the switch housing. Attach the switch housing cover
and light xture to the switch
housing using the included
attachment screws.
Switch
Housing
Cover
Plug
Nut
Washer
Screw
Hole
Switch
Housing
Cover
Attachment
Screw
Light Fixture
Non-Removable Switch
Housing
Steps 1-2
Steps 3-6
Attachment
Screw
Wires
and Wire
connectors
Step 7
CAUTION: Be sure no bare
metal wires or wire strands
are visible after making the
connections.
WARNING: Improper
installation could cause
the light xture to fall.
2 • Installing the Light fixture on Fans With Non-Removable Switch Housings
Page 7
7
43553-01 • 05/15/09 • Hunter Fan Company
2 • Installing the Light fixture on Fans With Non-Removable Switch Housings Cont.
9. Attach the light xture to the switch housing with the two
screws included with the light xture, aligning the holes in the
light xture, switch housing cover, and switch housing.
10. Securely tighten the two screws.
11. Go to the instructions for Installing the Bulbs and Shades.
Wires
and Wire
connectors
Steps 8-9
Page 8
8
43553-01 • 05/15/09 • Hunter Fan Company
1. Uninstall the two screws from the switch housing plate.
NOTE: Save the switch housing plate should you choose to remove the
light xture in the future.
2. Remove the wire connectors from the two wires in the switch housing
labeled “Connect Light Here” or “For Light Use.” One wire is white and the
other wire is black wire with a white stripe. read the two wires through
the hole in the center of the light xture.
3. To connect the wires, hold the bare metal leads together and place a wire
connector over them, then twist the wire connector clockwise until tight.
Connect the black/white striped wire from the switch housing to the black
wire from the light xture. Connect the white wire from the switch housing
to the white wire from the light xture. Secure all wire connections using
wire connectors.
CAUTION: Be sure no bare metal wires or wire strands are visible after
making the connections.
4. Attach the light xture to the switch housing with the two screws,
included with the light xture, aligning the holes in the xture, switch
housing cover, and switch housing.
5. Securely tighten the two screws.
6. Go to the instructions for Installing the
Bulbs and Shades.
Switch
Housing
Plate
Screw
Light
Fixture
Steps 3-6
Wires
and Wire
connectors
WARNING: Improper
installation could cause
the light xture to fall, or
result in electrical shock or
personal injury.
3 • Installing the Light fixture on the Hunter Originals
Page 9
9
43553-01 • 05/15/09 • Hunter Fan Company
Shade Cup
CFL bulb
(included)
1. Install four purchased shades for the light xture. For each
light, loosen the three thumbscrews in the shade cup. Place the
shade into the shade cup and tighten the thumbscrews.
2. Install the included CFL light bulbs.
3. e installation is complete and you can restore power to the
ceiling fan.
Steps 1– 3
umbscrews
4 • Installing Bulbs and Shades
Page 10
10
43553-01 • 05/15/09 • Hunter Fan Company
Troubleshooting
Light does not come on.
1. Make sure bulbs are installed properly.
2. Make sure breakers or fuses are on.
3. Verify that the light power lead is connected at the ceiling. Refer to
your ceiling fan manual for locating assembly and wiring.
Glass rattles.
1. Make sure the glass shades are secure.
If you need parts or service assistance, please call
888-830-1326 (In Canada, call 866-268-1936)or
visit us at our Web site at
http://www.hunterfan.com.
Hunter Fan Company
7130 Goodlett Farms Pkwy. # 400
Memphis, Tennessee 38016
is Light Fixture Weighs 4 lbs. Printed in China
5 • Troubleshooting
Loading...