Hunter Fan 41953-01 User Manual

41953-01 02/15/2008

1

I n s t a l l a t i o n G u i d e

83003 Aventine Bath Ventilator with Light

READ and SAVE THESE INSTRUCTIONS

ENGLISH

See page 2

ESPAÑOL

Vea la página 21

023_41953_EngS_2-15-08.indd 1 2/16/08 12:25:27 PM

41953-01 02/15/2008

2

DISCONNECT ELECTRIC

POWER SUPPLY

AND LOCK OUT

SERVICE PANEL BEFORE

SERVICING UNIT

W A R N I N G

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:

1. For general ventilating use only. Do not use to exhaust hazard-

ous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy/unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

3. DO NOT install this product in a wall. This product is designed

for installation in ceilings up to a 12/12 pitch (45 degrees).
Ductwork must point upward.

4. Pleasereadspecicationlabelonproductforfurtherinformation

and requirements.

PREVENTATIVE MAINTENANCE

A clean fan provides better service. Disconnect the power supply and
clean the fan as listed below.

TO CLEAN GRILLE: Use a mild detergent, such as dishwashing
liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads
or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle.
To remove motor plate, find the single tab on the motor plate (located
next to the receptacle). Push up rear motor plate tab while pushing
out on the side of the housing or insert a screwdriver into the slot in
the housing (next to tab) and twist screwdriver. Gently vacuum fan,
motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED
IN WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the
motor bearings are making excessive or unusual noises, replace the
motor with the exact service motor. You should replace the impeller at
the same time.

C A U T I O N

W A R N I N G

1. Use this unit only in a manner intended by the manufacturer.

If you have questions, contact the manufacturer.

2. Before servicing or cleaning the unit, switch power off at service

panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by quali-

edperson(s)inaccordancewithallapplicablecodesand
standards,includingre-ratedconstruction.

4. Sufcientairisneededforpropercombustionandexhausting

ofgassesthroughtheue(chimney)offuelburningequipment

to prevent backdrafting. Follow the heating equipment manufac­turer’s guideline and safety standards,such as those published
by the National Fire Prevention Association (NFPA), and the

American Society for Heating, Refrigeration and Air-Conditioning
Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall(s) or ceiling, do not damage

electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected to a
GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.

8. Never place a switch where it can be reached from a tub or

shower.

9. Installfanatleast5feet(1.52m)abovetheoor.

10. This unit must be grounded.

11. Unit must not be installed in a ceiling thermally insulated to a

value greater than R40.

Do Not Install Above

Or Inside This Area

Cooking

Equipment

Floor

45° 45°

COOKING AREA

023_41953_EngS_2-15-08.indd 2 2/16/08 12:25:27 PM

41953-01 02/15/2008

3

E

F

G

H

I

J

M

N

O

95044-01-000

95022-01-000

75867-01-000

03242-07-133

95492-06-000

74508-03-133

96392-01-500

K

77520-01

L

65219

75184-01-133

96395-01-000

P

75735-01-500

x5

*

*

*

NOTE:

Strain relief cable
connector must be
installed. Not Included.

A

B

C

Extra Screws

x2

D

3/8” Cable Connector

x2

1

Turn off the power source.

Tools Needed. (Not supplied.)

Estimated assembly time: 30 to 60 minutes

Before Installation

Check all the parts.

If damaged, call

1-888-830-1326

for replacements.

Included.

2

F

J

Loosen screws.

NOTE: Remove all packing materials before installation.

023_41953_EngS_2-15-08.indd 3 2/16/08 12:25:28 PM

41953-01 02/15/2008

4

5

4

7

H

8

G

Remove the motor/blower from the housing.

3

I

F

Remove the pre-loaded screw tip covers.

Remove the wiring cover screw.

6

Back out the pre-loaded screw tips until flush

with the side of the housing.

Remove the wiring cover.

Remove packing material.

023_41953_EngS_2-15-08.indd 4 2/16/08 12:25:29 PM

41953-01 02/15/2008

5

9

F

Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing

and secure with washer.

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

New Construction - attaching to joist

10

B

C

Choose Installation Option

For New Construction - attaching to joist go to step A11, page 5

For New Construction - suspended between joists go to step B11, page 8

For Existing Construction - accessible from above go to step C11, page 11

For Existing Construction - accessible only from below go to step D11, page 15

A11

F

5/8
1/2

5/8
1/2

A12

Screw pre-loaded screws into joist or framing.

023_41953_EngS_2-15-08.indd 5 2/16/08 12:25:30 PM

41953-01 02/15/2008

6

A

3 Pin

2 Pin

Fan Motor

Light

Light

Green

Black

Black

Red

Red

White

Black

Black

White

White

Bare Copper

Ground

Night Light

Night Light

Switch 1 (AC In)

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

A14

Connect wires as shown.

A13

Route wires through the strain relief.

0

A16

Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may need

to be purchased.

H

A15

F

Install the wiring cover plate. Make sure all

wiring connections are inside the box or under

the wiring cover plate.

023_41953_EngS_2-15-08.indd 6 2/16/08 12:25:31 PM

41953-01 02/15/2008

7

A19

J

A20

Reinstall the motor by inserting the tabs and pushing up into

position. Make sure the wires are not pinched

between the motor and the housing.

Secure the motor by tightening the 2 screws. Turn on the power source.

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

0000

A17

0000

I

A18

ON

OFF

A21

Test the motor. If the motor does not run,

check the plug connection.

A22

E1

Go to step

on page 17

to attach grille.

023_41953_EngS_2-15-08.indd 7 2/16/08 12:25:32 PM

41953-01 02/15/2008

8

Slide the mounting rails into brackets.

Mark position of screws by using holes as a template.

Insert screws, leaving space between the screw

head and the joist. Screws are not provided.

B11

E

F

5/8
1/2

5/8
1/2

B12

1/8” bit

B14

B15

B16

F

B13

Position the correct depth mark at the bottom edge of

the joist based on the thickness of your sheetrock.

Drill a hole in the center of each outline.

Attach the rails onto the screws.

New Construction – suspended between joists

023_41953_EngS_2-15-08.indd 8 2/16/08 12:25:33 PM

41953-01 02/15/2008

9

Tighten screws. Route wires through the strain relief.

B17

B18

Connect wires as shown.

A

3 Pin

2 Pin

Fan Motor

Light

Light

Green

Black

Black

Red

Red

White

Black

Black

White

White

Bare Copper

Ground

Night Light

Night Light

Switch 1 (AC In)

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

B19

B21

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

H

B20

G

Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may need

to be purchased.

023_41953_EngS_2-15-08.indd 9 2/16/08 12:25:35 PM

41953-01 02/15/2008

10

B27

E1

Go to step

on page 17

to attach grille.

B22

I

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

I

B23

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched

between the motor and the housing.

B25

Turn on the power source.

ON

OFF

B26

B24

J

Test the motor. If the motor does not run,

check the plug connection.

Secure the motor by tightening the 2 screws.

023_41953_EngS_2-15-08.indd 10 2/16/08 12:25:36 PM

41953-01 02/15/2008

11

C12

E

F

Existing Construction – accessible from above

EXISTING FAN

C11

NO EXISTING FAN

9”

9.75

”

OR

Remove an existing fan and check to make sure the

opening is large enough to accommodate the new

motor housing (9”x 9.75”).

Cut out an opening for the housing.

Use the motor housing as a template to mark position.

Slide the mounting rails into brackets.

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

5/8
1/2

5/8
1/2

C13

C14

Mark position of screws by using holes as a template.

023_41953_EngS_2-15-08.indd 11 2/16/08 12:25:37 PM

41953-01 02/15/2008

12

C17

C18

C19

C20

C15

C16

Drill a hole in the center of each outline. Insert screws, leaving space between the screw head

and the joist. Screws are not provided.

Attach the rails onto the screws. Tighten screws.

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may

need to be purchased.

Route wires through the strain relief.

023_41953_EngS_2-15-08.indd 12 2/16/08 12:25:38 PM