Hunter Plug-In
41764-01 04/04/2005
TM
Bowl Style Light Fixture
Installation Instructions
41764-01_Rev 4-4-05.indd 1 4/4/05, 2:27:38 PM
CAUTIONS
• Read entire installation instructions carefully before beginning installation and save these instructions.
• To reduce the risk of electrical shock, install this light fi xture only on
Hunter
the ceiling fan package or on the name plate label located on top of
the motor housing of the ceiling fan.
TM
fan type 8, 9, 10 or 11. Note: e fan type can be found on
WARNINGS
• To avoid possible electrical shock, before installing light fi xtures disconnect power by turning off the circuit breakers both to the outlet
box and to its associated wall switch location. If you cannot lock the
circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
• Connect house wiring to the fan before attaching the light fi xture to
the fan.
• All wiring must be in accordance with national and local electrical
codes. If you are unfamiliar with wiring, you should use a qualifi ed
electrician. Professional installation is recommended.
Tr o ub l e shooting
Light fi xture will not plug into switch housing.
1. Contact Hunter Fan Company Technical Support at 1-888-830-1326 or
return light fi xture to store purchased at. WARNING: Do not bend prongs
on the light fi xture or attempt to force the light fi xture plug into the
switch housing.
Light does not come on.
1. Pull light pull chain one or two times to see if light comes on.
2. Make sure bulbs are installed properly and fi lament is not blown.
3. Make sure breakers or fuses are on.
4. Verify that the light power lead is connected at the ceiling. Refer to your
ceiling fan manual for locating assembly and wiring.
Glass rattles.
1. Securely tighten the fi nial.
41764-01_Rev 4-4-05.indd 2 4/4/05, 2:27:41 PM
For other problems or ques-
tions, contact the Hunter Fan
Company Technical Support
at
1-888-830-1326 or
techsupport@hunterfan.com.
http://www.hunterfan.com
1. Disconnect power to the ceiling fan by turning off the circuit breakers
both to the outlet box and to its associated wall switch location.
2. Unscrew the fi nial to remove the fi nial and switch housing cap.
Note: Save the fi nial and switch housing cap should you choose to re-
move the light fi xture in the future.
3. Plug-in the light fi xture and turn the gear wheel to the right (clockwise) to
secure the light fi xture. WARNING: Improper installation could cause the
light fi xture to fall.
4. Install 2 - 60 W Max A-15 bulbs.
5. Attach the 8” extension chain to the fan pull chain. Attach the 4” extension chain to the light pull chain.
6. Snap the adapter into the hole in the glass bowl.
7. read the light pull chain through the center hole in the adapter, cap
and fi nial. read the fan pull chain through the side hole in the adapter
and cap.
8. Place the glass bowl and cap over the threaded rod.
9. Screw the fi nial onto the end of threaded rod to secure the glass bowl.
Note: If the glass bowl is crooked, you can loosen the fi nial and adjust the
glass bowl until it is level. Once level, securely tighten the fi nial.
10. Restore power to the ceiling fan.
Switch Housing
Cap
Step 2
Finial
Fan Pull
Chain
readed Rod
Adapter
41764-01_Rev 4-4-05.indd 3 4/4/05, 2:27:41 PM
Light Pull
Chain
Glass Bowl
Cap
Finial
Gear
Wheel
Light
Fixture
Step 3Steps 5-9
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
is Light Fixture weighs 3.0 lbs.
41764-01_Rev 4-4-05.indd 4 4/4/05, 2:27:44 PM
© 2005 Hunter Fan Company
Printed in China & Taiwan
Loading...