Hunter Fan 36259 User Manual

®

SINCE 1886

TM

True HEPA Air Purifier

EnglishSpanishGermanFrenchItalianDanishDutchPortuguese

QuietFlo

2

3

1

0

Models 36114 & 36115

0

1

2

QuietFlo

3

P
r

e

­F
i

l
t

e
r
F
i

l
t

e

R

r

e

QuietFlo

0

P
r

e

­F
i

F

l

i

t

l

e

1

t

r

F

e

i

r

l

R

t

e

e

s

r

e

t

2
3

Models 36144 & 36145

F
i

l
t

e

s

r

e

t

Models 36259 & 36260 Models 36394 & 36395

41481 10-5-2001 © 2001 Hunter Fan Company

®

IMPORTANT SAFETY INSTRUCTIONS

English

READ ALL INSTRUCTIONS BEFORE USING THIS AIR PURIFIER.

1. This Air Purifier is designed for use on a flat, level surface and
may not work properly on an uneven surface. ALWAYS place
this Air Purifier on a firm, level surface. ALWAYS place the Air
Purifier at least six (6) inches away from walls and heat sources
such as stoves, radiators, or heaters.

2. Place the Air Purifier in an area that is out of the reach of
children.

3. Before using the Air Purifier, extend the cord and inspect for
any signs of damage. If the supply cord is damaged, it must be
replaced by a manufacturer or its service agent or similarly
qualified person in order to avoid hazard.

4. If the plug does not fit fully and securely into the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician.
DO NOT attempt to use the unit unless the plug fits securely
into the socket.

5. ALWAYS UNPLUG the Air Purifier when it is not in operation,
while the filter is being changed, or while it is being cleaned.

6. DO NOT tilt or move the Air Purifier while it is in operation.
Shut off and unplug before moving.

7. DO NOT immerse the Air Purifier in water, as permanent
damage will occur. Refer to and follow the AIR PURIFIER
MAINTENANCE instructions.

READ AND SAVE ALL INSTRUCTIONS.

2 41481-01 10-5-2001

INTRODUCTION

Thank you for purchasing the QuietFlo™ T rue HEP A Air Purifier from Hunter
Fan Company. You have purchased our latest development in portable
Air Purification Systems. This system has been developed to improve the
quality of the air you breathe.

Our QuietFlo™ True HEPA Air Purifier out performs other air purification
systems by quickly and effectively removing dust, smoke, and pollen
particles. The HEPA filter will remove 99.97% of particles 0.3 microns in
size from air that passes through the filter.

The activated carbon pre-filter helps remove cooking, smoke, and pet
odors from the air. It also traps lint, hair, and large particles, which helps
improve the life and performance of the HEPA filter.

HOW THE QUIETFLO™ HEPA AIR PURIFIER WORKS

As the air is pulled into the purifier , the activated carbon pre-filter absorbs
odors and catches large particles. Then, the air travels through the HEP A
filter where the smaller particles are collected. Finally, the clean purified
air is released back into the room.

®

English

Dust & Irritants Pollen & Allergies Odors Bacteria Pet Hair & Dander

Carbon
Pre-filter

Figure 1- Illustration of the Air Filtration System

41481-01 10-5-2001 3

True HEPA Filter

99.97% -- .3 Microns

®

SETTING UP YOUR AIR PURIFIER

1. Remove your air purifier from the box and take it out of the clear

English

plastic protective bag.

2. Place your QuietFlo™ Air Purifier on a firm, flat surface.

3. Before turning the Air Purifier ON, you need to open the front grille.
For Models 36114/36115/36144/36145: To release the front grille,

press the tabs until the front grille slides easily over the tabs. Refer to
Figures 2a on page 5.

For Models 36259/36260/36394/36395: To release the front grille,
place your fingers behind the tabs and pull forward. Refer to Figures
3a and 3b on page 6.

4. The HEP A filter is already installed, but you should confirm that it has
not shifted during shipment. Check the position of the HEPA filter
by pressing firmly on all four corners to ensure that it is fully inserted
into the filter opening.

5. The carbon pre-filter is mounted inside the front grille with hook
tape. Confirm that it covers the grille vents. Refer to Figures 2b, 3c,
and 3d on pages 5 and 6.

6. Find the filter installation reminder sticker on the inside edge of the
front grille or unit. Circle the month and write the year of installation
for the pre-filter and HEPA filter.

7. Replace the front grille. Be sure that the bottom grille tabs are in
position first, and then push the top of the grille forward until it is
closed. The unit is now ready for normal operation.

Note: The unit will not operate unless the door is placed in the correct
position.

8. Plug the unit into the proper voltage outlet

RatingHunter Model No.

36114
36144
36259

120 V 60 Hz

36394
36115

36145
36260

220-240 V 50 Hz

36395

4 41481-01 10-5-2001

®

HEPA Filter

QuietFlo

2

3

1

0

Front Grille

Pre-filter

Figure 2a - Models 36114 & 36115

Hook Tape

Inside View of

Grille Vents

Front Grille

Tab

Hook Tape

Figure 2b - Models 36114, 36115, 36144 & 36145

Press to
Open
Front Grille

English

41481-01 10-5-2001 5

English

HEPA Filter

®

Front Grille

Pre-filter

0

1

2
3

Figure 3a - Models 36259 & 36260

QuietFlo

FilterPre-Filter

Filter

Reset

Recess for
Fingers to
Open Front
Grille

Control Panel

Front Grille

Pre-filter

Recess for
Fingers to
Open Front
Grille

HEPA Filter

Figure 3b - Models 36394 & 36395

Inside View
of Front Grille

Hook Tape

Hook Tape

Grille Vents

Inside View of
Front Grille

Tab

Hook Tape

Hook Tape

Figure 3c - Models 36259 & 36260 Figure 3d - Models 36394 & 36395

Grille Vents

6 41481-01 10-5-2001

OPERATING YOUR AIR PURIFIER

Models 36114, 36115, 36144, 36145, 36259, 36260:

On/Speed Control: Rotate the Speed Control knob to set the desired
speed. As you rotate the knob clockwise, the fan speed changes from off
to low to medium to high. T urn the knob counter clockwise to decr ease
the fan speed or turn the unit off. The fan speed can be adjusted at any
time.

Model 36394, 36395:

On/Speed Control: Press the On button ( ) to turn the unit on. When
you press it once, the fan speed will be at a setting of low (1). To switch

to a speed setting of medium (2) or high (3), continue pressing the button.
Off: Press the Off button ( ) to turn the unit off.

Timer: If you want the air purifier to shut off automatically, you can set
the timer. Press the Timer button ( ) to choose the amount of time

you would like the air purifier to run (1, 2, 4, or 8 hours). Press the
button repeatedly to change the length of time.

PRE-FILTER AND FILTER COUNTERS

Models 36144, 36145, 36259, 36260, 36394, 36395:

These air purifiers contain counters that indicate when the pre-filter and
filter should be changed. The counter automatically counts the number
of hours that each filter has been is use. When the pre-filter counter
reaches 2000 hours (approximately three months of use), the pre-filter
indicator will be lit to show that the pre-filter should be changed. When
the HEPA filter counter reaches 8000 hours (approximately one year of
use), the HEPA filter indicator will be lit to indicate that the filter should
be changed. The exact life of the pre-filter and filter will depend upon
the environment. If necessary, the filters should be changed more
frequently

To reset the pr e-filter or filter counters when one indicator (or both) is lit:

1. Change the filter and/or pre-filter as described in the Maintenance

section of the manual.

2. To reset the counter back to zero hours and turn off the indicator,

press and hold the filter reset key for three seconds. If both the pr e­filter and filter indicators are lit, the reset key will first turn off the
pre-filter indicator. Then, you must release the reset key and then
press and hold the filter reset key again for three seconds to turn off
the filter indicator.

For Models 36394 and 36395: Use the tip of a pen or pencil to press
the key.

®

English

41481-01 10-5-2001 7

®

To reset the pre-filter or filter counters before the indicators are lit:
In some environments, you may want to change the pre-filter or filter

English

more frequently than indicated by the filter indicators. This procedure
allows you to reset the pre-filter or filter counter before the indicators ar e
lit.

1. Change the filter and/or pre-filter as described in the Maintenance
section of the manual.

2. Now, you must choose which counter you want to reset. Press and
hold the filter reset key (approximately three seconds) until the pre­filter indicator flashes. Press and release the reset key again to
alternate between the two indicators. The counter that will be reset
is designated by the flashing indicator.

For Models 36394 and 36395: Use the tip of a pen or pencil to press
the key.

3. Once you have the correct indicator flashing, press and hold the reset
key for three seconds to reset that counter to zero hours. The indicator
will stop flashing when it has been reset. If needed, repeat these
steps to reset the other counter.

AIR PURIFIER MAINTENANCE

CLEANING YOUR AIR PURIFIER

Proper maintenance of your Hunter Air Purifier will help ensure years of
trouble free service. Follow these steps to properly maintain your air
purifier:

1. Approximately every 90 days, the outside of the unit should be cleaned
with a soft, damp cloth.

2. If needed, the front grille can be removed from the unit and cleaned
with soapy water. Simply remove the pre-filter before exposing the
grille to water.

3. Use the following instructions to determine when and how to replace
the filter and pre-filters.

Notes:

· The air purifier should be unplugged during all cleaning processes.

· Be sure the unit is completely dry before plugging in and using.

· Never immerse the unit in water.

8 41481-01 10-5-2001

CHANGING THE PRE-FILTER

In a typical environment, the pre-filter should be changed every 2000
hours (approximately 3 months of use) to maintain proper odor -removing
capability and overall filtration performance. Changing the pre-filter
regularly will also help extend the life of the HEPA filter. If necessary, the
pre-filter can be changed more frequently. The following instructions tell
you how to change the pre-filter.

For Models 36144, 36145, 36259, 36260, 36394, 36395: The pre-filter
indicator will flash after 2000 hours of use as a reminder that you should
change the pre-filter.

1. Turn OFF and unplug the air purifier .

2. Remove the front grille to expose the pre-filter. The pre-filter is

attached to the front grille with hook tape. Pull gently on the pre­filter to remove it. Once removed, you can dispose of the used pre­filter.

3. If needed, use a soft damp cloth to wipe off the front grille.

4. Remove the new pre-filter from the plastic wrapping and install it in

the grille by pressing gently on the corners where it adheres to the
hook tape. Y ou may notice a few black particles coming off the pr e­filter . Those particles ar e part of the odor -removing activated carbon
and will be collected on the filter during normal use. Mark the new
filter installation sticker included with the pre-filter and place the
sticker on the front grille for future reference.

5. Install the front grille onto the unit and plug in the air purifier.

6. For Models 36144, 36145, 36259, 36260, 36394, 36395: Reset the

pre-filter counter as described in the Pre-filter and Filter Counter section
of this manual.

CHANGING THE HEPA FILTER

Although the proper time to change the filter depends on usage and the
environment, a typical life is 8000 hours (approximately 1 year of usage).
If you notice a decrease in air output or an increase in noise at any time
during normal operation, the filter may be clogged and need to be
replaced. A color -coded chart is also included on the inside of the housing
to help you determine if it is time to change the HEP A filter. Follow these
instructions to change the HEPA filter.

For Models 36144, 36145, 36259, 36260, 36394, 36395: The filter
indicator will flash after 8000 hours of use as a reminder that you should
change the filter.

1. Turn OFF and unplug the air purifier .

2. Remove the front grille and gently pull on the filter to remove it from

the unit. While removing the filter, note the direction of the flaps
that form the seal around the filter. The new filter will be installed

41481-01 10-5-2001 9

®

English

®

with the same orientation. Once removed, the used filter can be
discarded.

English

3. Remove the new filter from its wrapping and look at the orientation
of the rubber seals on the sides of the filter. The loose ends of the
flaps should be facing out as the filter is placed into the air purifier.
Press firmly on the filter frame to ensure that the filter is fully inserted
into the housing. Mark the new filter installation sticker included
with the filter and place the sticker on the front grille for future
reference.

4. Install the front grille onto the unit and plug in the air purifier.

5. For Models 36144, 36145, 36259, 36260, 36394, 36395: Reset the
filter counter as described in the Pre-filter and Filter Counter section
of this manual.

REPLACEMENT FILTERS:

T o obtain replacement filters for your Air Purifier, contact your local retailer
where the unit was purchased. Please be prepar ed to tell the retailer the
model number of your air purifier and the model number of your
replacement filters that are listed below. The model number of your air
purifier is located on the rating sticker on the back of the unit. The
replacement filter model numbers are listed in the table below.

Air Purifier
Model No.

Pre-filter
Model No.

HEPA Filter
Model No.

36114
36115
36144

30907

30938

36145
36259

36260

30903

30940

36394
36395

10 41481-01 10-5-2001

30907

ELECTRICAL CORD STORAGE

Models 36114, 36115, 36144, 36145:

For your convenience, this air purifier has cord wrap posts for easy storage
of the electrical cord. The cord wrap posts are located on the back of the
air purifier in the bottom corners.

When received, the cord wrap posts will be in the collapsed position. To
extend the cord wrap posts, simply twist approximately 1/8 of a rotation
and gently pull outward. The post will extend approximately 0.5 inches
(refer to Figure 4). Once extended, wrap the cord around the two posts
until the desired length is obtained.

Figure 4 - Extended Cord Wrap Posts

®

English

41481-01 10-5-2001 11

Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
United States of America
http://www.hunterfan.com

© 2001 Hunter Fan Company 41481 10-5-2001