HunterDouglas SOLERA Installation Operation And Care
Solera® Soft Shades
PowerView™ Motorization
Installation • Operation • Care
CONTENTS
Questions?
Call the Hunter Douglas Customer Information Center at
1-888-501-8364.
© 2016 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or
their respective owners.
Getting Started:
Product View .................................................................. 1
Tools and Fasteners Needed ............................................ 2
Installation:
Installation Overview ...................................................... 3
STEP 1 — Install the Brackets ......................................... 3
Mount the Installation Brackets — Inside Mount ............... 4
Mount the Installation Brackets — Outside Mount ............ 6
STEP 2 — Install the Shade ............................................ 8
STEP 3 — Connect the Power Source .............................. 9
Operation:
Testing the Shade ......................................................... 13
Using the PowerView
™
Remote ...................................... 13
Resetting the Shade (If Necessary) ................................. 15
Adjustment ................................................................... 16
Troubleshooting ............................................................ 16
Care:
Removing the Shade (If Necessary) ................................ 18
Cleaning Procedures ..................................................... 18
Declarations ................................................................ 19
Warranty .......................................................... Back Cover
GETTING STARTED
1
Product View
Not Shown: Top-
Down/Bottom-Up Shades and spacer blocks for an outside mount with attached battery wand.
Satellite Battery Pack or
DC
Power Supply (Optional)
Attached
Battery Wand
(Standard)
DC Po
wer Supply
Installation
Brackets
Manual
Control
Button
2
GETTING STARTED
Thank you for purchasing Hunter Douglas Solera® Soft Shades with PowerView™ Motorized
Lifting System. With proper installation, operation, and care, your new shades will provide years
of beauty and performance.
Please thoroughly review this instruction booklet and the enclosed packing list before beginning
the installation.
Tools and Fasteners Needed
■ Flat blade and Phillips screwdriver
■ Measuring tape and pencil
■ Level (laser level is recommended)
■ Power drill,
3
∕32" drill bit, and 1∕4" hex driver
In addition, you will need fasteners designed to work with your specific mounting surface(s).
■ #6 x 1½" Hex Head Screws (Provided). Two 1½" screws are provided per installation
bracket.
■ Speed Nuts and Screws (Provided). If ordered, extension brackets come with speed nuts
and screws.
■ Drywall Anchor (Not Provided). Use drywall anchors when mounting into drywall.
■ #6 x 2" Hex Head Screws (Provided). If using spacer blocks, two 2" screws are
provided per installation bracket.
#6 x 1½"
Hex Head Screw
Speed Nut
and Screw
(Provided
With Each
Extension Bracket)
#6 x 2" Hex Head Screw
for Use with Spacer Blocks
INSTALLATION
3
Installation Overview
To install your shade, you will need to perform the following three easy steps:
STEP 1: Install the Brackets
STEP 2: Install the Shade
STEP 3: Connect the Power Source
STEP 1 — Install the Brackets
■ Your order will include installation brackets specific to your
shade. The number of installation brackets required varies
with headrail width, as shown in the table below.
Important: A
5
/8" spacer block (provided) is required
for outside mount shades using the battery wand clip.
Mounting Types and Window Terminology
If the installation brackets are mounted correctly, the rest of the installation process follows very
easily. To prepare for this important first step, review the mounting types and basic window
terminology illustrated below.
■ Refer to the appropriate page below based on your order:
➤ Inside Mount — Page 4
➤ Outside Mount — Page 6
Installation
Bracket
Spacer
Block
Shade
Width
Brackets
Required
15" – 30" 2
30
1
/8" – 54" 3
54
1
/8" – 78" 4
78
1
/8" – 102" 5
102
1
/8" – 126" 6
126
1
/8" – 135" 7
Outside Mount
Shade mounts outside
window opening.
Inside Mount
Shade fits within
window opening.
Collectively, the sill and
jambs are called the
“window casement.”
Molding
Head Jamb
Sill
Jamb Jamb
INSTALLATION
4
Mount the Installation Brackets — Inside Mount
■ Mark 2" in from each jamb.
➤ If more than two installation brackets came with your order, space additional bracket(s)
evenly between the two end brackets and mark their location. Mount into wood
whenever possible.
➤ With shades using a battery wand, there must be a minimum of 15½" between brackets
at the motor end.
➤ With shades using two battery wands, there must be a minimum of 18" between
brackets at the motor end.
■ Center the brackets on your marks, then mark each of the screw holes.
➤ For fully recessed and minimum mounting depth based on your order options, see the
illustration on the next page.
Important: The front edges of the installation brackets must be level and aligned.
2" 2"Space EvenlySpace Evenly
Jamb Jamb
Jamb
Motor
End
Jamb
Space Evenly
2" 2"
Space Evenly
Shades with Attached Battery Wand(s) (Top View)
Min. of 15½" for a Battery Wand or
18" for Two Battery Wands
on the Motor End
Bracket
Window Casement
Window
Battery Wand
Bracket
Window Casement
Window
2½" Minimum Inside Mount 31/8" Fully Recessed Mount
2½
"
Bracket
Battery Wand
Wall
2½" Fully Recessed Mount
Window Casement
Bracket
Window Casement
Window
With Attached Battery Wand
Satellite Battery Pack or DC Power Supply
Window
5
/
8
"
Needed for Rear Clearance
7
/
8
"
Min Inside Mount
3
1
/8"
5
/8"
5
/8"
INSTALLATION
5
Bracket
Window Casement
Window
Battery Wand
Bracket
Window Casement
Window
2½" Minimum Inside Mount 31/8" Fully Recessed Mount
2½
"
Bracket
Battery Wand
Wall
2½" Fully Recessed Mount
Window Casement
Bracket
Window Casement
Window
With Attached Battery Wand
Satellite Battery Pack or DC Power Supply
Window
5
/
8
"
Needed for Rear Clearance
7
/
8
"
Min Inside Mount
3
1
/8"
5
/8"
5
/8"
INSTALLATION
6
■ Drill the screw holes using a 3/32" drill bit.
■ Attach the installation brackets using the screws provided.
➤ Check that the mounting surface is level and the brackets are aligned. If mounting to a
heavily textured surface, shim the brackets, if needed.
Important: Use drywall anchors when mounting into drywall. Drywall anchors are
not provided.
Proceed to “STEP 2 — Install the Shade” on page 8.
Mount the Installation Brackets — Outside Mount
The standard shade has an attached battery wand requiring a spacer block to be used with the
installation bracket, as illustrated on the next page. DC power supply or satellite battery pack will
not require a spacer block.
■ Center the headrail over the window opening at the desired height. Use a pencil to lightly
mark each end of the headrail.
➤ Alternatively, measure the width of the headrail and use that width to mark the headrail
end points over the window opening.
■ Mark 2" in from each end of the headrail.
➤ If more than two installation brackets came with your order, space additional bracket(s)
evenly between the two end brackets and mark their location. Mount into wood
whenever possible.
➤ With shades using a battery wand, there must be a minimum of 15½" between brackets
at the motor end.
➤ With shades using two battery wands, there must be a minimum of 18" between
brackets at the motor end.
Headrail End Marks
Window Opening
2" 2"
Space EvenlySpace Evenly
Min. of 15½" for a Battery Wand or
18" for Two Battery Wands
on the Motor End
Loading...