HunterDouglas Powerview, Powerview App2 Version Quick Start Manual

This guide will help getting you started with your Powerview® purchase.

supply).

colours. Please locate them all before you start.

seamless installation of the PowerView® system.

Note

If you only have one remote, please proceed to

step 4

.

MANUAL

Powerview® Quick Start Guide Gen 1

Step 1. Install your shades

Make sure you have properly installed your shades and that they are connected to a power source (battery ack or power

Step 2. Your Powerview® components

Packed with your purchased product you will nd one or more remotes, repeaters and a Hub (which is optional and only
required when you want to control your shades using a tablet or smartphone). Remotes come in different shapes and

Wall Surface

Pebble

Step 3. Pairing remotes

Repeater

Hub (optional), required
for controlling your
shades with a tablet or
smartphone.

By pairing PowerView® remotes you make all your remotes part of the same PowerView® Network. This is important for

Page 1 of 14 version: 1.0

MANUAL

This instruction will make use of the following button
on the remote:

3.1 Take all remotes.

Name one remote "SOURCE"

Name the rest of the remotes "TARGET"

Repeat the following steps until all "TARGET"
remotes have been set.

3.2 "TARGET REMOTE" : Remove back cover.

Keep the batteries in place

Page 2 of 14 version: 1.0

MANUAL

3.3 "TARGET REMOTE" : Press the reset button

for six seconds.

The group buttons will ash on the press of
the Reset button, then again at six seconds.

3.4 "TARGET REMOTE" : Close the cover.

3.5

3.6

3.7

3.8

"SOURCE REMOTE" : Press  stop for 6

seconds.

Keep pressing until the remote lights start
blinking.

"TARGET REMOTE" : Press  stop and hold

"SOURCE REMOTE" : Press  stop and

release

"TARGET REMOTE" : Release  stop

As conrmation "TARGET REMOTE" will ash
the group buttons.

3.9 "SOURCE REMOTE" : If the buttons are still

ashing Press  stop for 6 seconds.

Keep pressing until the ashing stops.

Page 3 of 14 version: 1.0

A Remote can control 6 groups of shades (which are the buttons 1 to 6). The instructions below assign a shade to group

MANUAL

Step 4. Adding a shade to a remote

1. Depending on your preference you can choose your own group.

This instruction will make use of the following buttons on the
Remote:

Find the Shade button on your shade.

Different shade types have different shade buttons.

Consult the shade documentation for the exact location of the
shade button.

4.1

4.2

Press  stop for 6 seconds.

Keep pressing until the remote lights start blinking.

Press  group1 .

This will activate the group 1 on the remote.

4.3 Press and hold the Shade button .

4.4

Page 4 of 14 version: 1.0

Press the  open button

You will see the shade move up and down shortly.

MANUAL

4.5 Release the Shade button .

4.6 If your remote is still ashing Press stop for 6

seconds.

Keep pressing until the ashing stops.

Step 5. Install repeaters

Installation of a repeater is necessary when your shade is not responding to a command from your remote control.
Preferably put the repeater halfway between the unresponsive shade and the remote control location.

This instruction will make use of the  stop button on your
remote

and the Repeater button on the repeater.

5.1 Place the repater in the USB charger and plug it in an

outlet

The

repeater light

illuminates green.

Page 5 of 14 version: 1.0

Step 6. Connect and setup the Hub.

MANUAL

5.2

5.3 Hold the remote within 20cm. from the repeater.

5.4

Press  stop for 6 seconds.

(Keep pressing until the remote lights start blinking.)

Press  stop .

(The

repeater light

now part of your personal Powerview® Network.)

will turn off. The repeater is

If you have not purchased a Hub please proceed to Additional actions to proceed with your installation.

6.1 Connect the Hub to your home network router

6.2 Connect the Hub to your power outlet

Page 6 of 14 version: 1.0

Step 7. Connect the Powerview® app to the Hub.

Take your remote control.

MANUAL

6.3 Check the range of the Hub

Your Hub should be able to reach each shade in the
house.

Use your remote from the same location as your Hub
to operate your shades. If some shades do not
respond, add or relocate a repeater and check again.

6.4 Wait approximately 2 minutes and observe the Hub

light.

• Blue/Red blinking : All ok. Proceed with the
installation.

• Red blinking : Hub is downloading updates.
Please wait. (approx. 5 mins.)

• Continuous blue : Hub is already connected to a
network. If you have previously setup your hub
you can continue. If not you can clear the data on
the hub. Goto Erase hub data in the Additional
actions chapter.

7.1 Download the Powerview® app from the app store or
play store.

7.2 Start the app.

(The app will start looking for an available Hub.)

7.3 Wait for the rst screen to appear and click Connect

to a hub

Page 7 of 14 version: 1.0

Additional actions.

Your Powerview Network is now setup and ready to be further adjusted to your preferences. Follow the steps in this

chapter or go to

For further instructions please go to

www.luxaex.co.uk/powerview-installation

.

MANUAL

7.4 Follow the instructions until you get to this screen

7.5 Choose 1 remote

7.6 Follow the onscreen instructions to add the hub to
your existing Powerview® network

7.7 You can now start with the app.

www.luxaex.co.uk/powerview-installation for more information.

Operate a shade

This instruction will make use of the following buttons
on the remote:

Page 8 of 14 version: 1.0

Set a favorite position

MANUAL

1. Press group 1

(Group 1 will light up.)

2.

3.

2.

Press  open

(Shades assigned to group 1 will open)

Press  stop

(Shades assigned to group 1 will stop)

Press  close

(Shades assigned to group 1 will close)

Pressing all instead of group 1 will move all shades from all 6 groups on the remote.

This instruction will make use of the following buttons
on the remote:

Find the shade button on your shade.

(Different shade types have different shade buttons.
Consult the shade documentation for the exact
location of the

Page 9 of 14 version: 1.0

shade button

)

MANUAL

1. Move your shade to the desired favorite position

(Use your open, close and stop buttons to move the shade.)

2.

3. Press and hold the shade button .

4.

Press  stop for 6 seconds.

(Keep pressing until the remote lights start blinking.)

Press the  favorite button

(You will see the shade move up and down briey.)

5. Release the shade button .

6. If your remote is still ashing Press stop for 6 seconds.

(Keep pressing until the ashing stops.)

Move a shade to a favorite position

This instruction will make use of the following buttons
on the Remote:

1. Move shades assigned to group 1 to their favorite position.

1. Press group 1

Page 10 of 14 version: 1.0

(Group 1 will light up.)

This will remove a shade from a group on your remote control. It will not remove the shade from the Powerview®

MANUAL

2. Press favorite

(Shades assigned to group 1 will move to their favorite position.)

Pressing all instead of group 1 will move all shades from all 6 groups to their favorite position.

Remove a shade from a group

network.

This instruction will make use of the following buttons
on the Remote:

Find the shade button on your shade.

(Different shade types have different shade buttons.
Consult the shade documentation for the exact
location of the

Follow the below instructions for each Powerview® shade. Depending on your preference choose a group on one of your
remotes. (In this example group 1 is used.)

1.

2.

shade button

Press  stop for 6 seconds.

(Keep pressing until the remote lights start blinking.)

Press  group1 .

)

(This will activate the group 1 on the remote.)

3. Press and hold the shade button .

Page 11 of 14 version: 1.0

A Scene Controller works in combination with the Powerview® App. It can activate scenes which are created in the App.

MANUAL

4.

5. Release the shade button .

6. If your remote is still ashing Press stop for 6 seconds.

Press the  close button

(You will see the shade move up and down shortly.)

(Keep pressing until the ashing stops.)

Install a Scene Controller

1. Start the App and open the side menu.

2. Select Scene Controllers and follow the App
instructions.

Page 12 of 14 version: 1.0

MANUAL

Erase hub data

Find the following button on the back of the Hub.

1. Press hub erase for 6 seconds

2. Wait for the hub to start ashing red and blue.

All data on the hub is now cleared.

Page 13 of 14 version: 1.0

its products and services, and to discontinue any product or service. Buyers should obtain the latest relevant information before placing orders and

should verify that such information is current and complete. All products (also referred to herein as "components") are sold subject to Hunter Douglas’

terms and conditions of sale supplied at the time of order acknowledgment. Hunter Douglas warrants performance of its components to the

specications applicable at the time of sale, in accordance with its standard warranty terms. Testing and other quality control techniques are used to the

extent Hunter Douglas deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each

component is not necessarily performed. Hunter Douglas assumes no liability for applications assistance or the design of Buyers' products. Buyers are

responsible for their products, applications and interfaces using Hunter Douglas components. To minimize the risks associated with Buyers' products

and applications, Buyers should provide adequate design and operating safeguards. Hunter Douglas does not warrant or represent that any license,

either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination,

machine, or process in which Hunter Douglas components or services are used. Information published by Hunter Douglas regarding third-party products

or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a

license from a third party under the patents or other intellectual property of the third party, or a license from Hunter Douglas under the patents or other

intellectual property of Hunter Douglas. Reproduction of Hunter Douglas information in Hunter Douglas data sheets is permissible only if reproduction is

without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Hunter Douglas is not responsible or liable for

any altered documentation. Information of third parties may be subject to additional restrictions. Resale of Hunter Douglas components or services with

statements different from or beyond the parameters stated by Hunter Douglas for that component or service voids all express and any implied

warranties for the associated Hunter Douglas component or service and is an unfair and deceptive business practice. Hunter Douglas is not responsible

or liable for any such statements. Buyers acknowledge and agree that they are solely responsible for compliance with all legal, regulatory and safety-

related requirements concerning its products, and any use of Hunter Douglas components in its applications, notwithstanding any applications-related

information or support that may be provided by Hunter Douglas. Buyers represent and agree that they have all the necessary expertise to create and

implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures

that might cause harm and take appropriate remedial actions. Buyers fully indemnify Hunter Douglas and its representatives against any damages

arising out of the use of any Hunter Douglas components in safety-critical applications.

MANUAL

Important notice

Page 14 of 14 version: 1.0