Page 1
Traditional Globe
Traditional Globe
Light Kit
Light Kit
Installation Manual
Compatible with:
2xxxx Types A - Z
51000-58999 fan series
59500-59999 fan series
Select Casablanca Fans
MA022-01 • 03/07/14
Models 99164, 99165, 99166
Page 2
1.888.830.1326
BEFORE YOU BEGIN
Read entire installation instructions carefully before
beginning installation and save these instructions.
Switch
Housing
Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s
switch housing. Begin on page 3 where you will choose the type of switch housing that
most closely resembles the one on your fan. From there, you will be directed to the set
of assembly instructions that are appropriate for installing the light kit to your fan.
READ AND SAVE THESE INSTRUCTIONS
This product conforms to UL Standard 507.
WARNINGS
w.1 - To reduce the risk of re, electrical shock, or personal injury,
mount fan directly from building structure and/or an outlet box marked
acceptable for fan support of 70 lbs. (31.8 kg) and use the mounting screws
provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet
box and associated wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent warning device,
such as a tag, to the service panel.
CAUTIONS
c.1 - All wiring must be in accordance with national and local electrical codes
ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.
2
MA022-01 • 03/07/14
Turn Power
OFF
Page 3
1.888.830.1326
WHICH ASSEMBLY METHOD WILL I USE?
Choose one of the four images below that most closely resembles the switch
housing on your fan; then follow the instructions under the image.
Switch
Housing
Cap
Cap
Screw
If you are installing this light kit onto
a Hunter Original, remove the cap
screws with a Phillips head screwdriver.
Keep the screws Remove the cap.
Then follow the TYPE-A ASSEMBLY
INSTRUCTIONS on pages 4-5.
Switch
Housing
Screw
Switch
Housing
Cap
If your fan’s switch housing cap
resembles this one, remove
the whole switch housing by
removing the switch housing
screws with a Phillips head
screwdriver. Remove the two
cap screws from the inside of
the switch housing. Reinstall
the switch housing. Tighten the
switch housing screws. Then
follow the TYPE-B ASSEMBLY
INSTRUCTIONS on pages 6-7.
Cap
Screw
If your fan’s switch housing cap
resembles this one, remove the cap
screws with a Phillips head screwdriver.
Then follow the TYPE-B ASSEMBLY
INSTRUCTIONS on pages 6-7.
Switch
Housing
Screw
Plug
Button
If your fan’s switch housing cap
resembles this one, remove
the whole switch housing by
removing the switch housing
screws with a Phillips head
screwdriver. Remove the plug
button. Then follow the TYPE-C
ASSEMBLY INSTRUCTIONS on
pages 8-9.
3
MA022-01 • 03/07/14
Switch
Housing
Cap
Plug
Button
Switch
Housing
Screw
If your fan’s switch housing
cap resembles this one,
remove the whole switch
housing by removing the
switch housing screws with
a Phillips head screwdriver.
Remove the plug button using
a standard screwdriver. Then
follow the TYPE-D ASSEMBLY
INSTRUCTIONS on pages 10-11.
Page 4
TYPE-A ASSEMBLY INSTRUCTIONS
1.888.830.1326
1
Switch
Housing
If your fan does not have pin connectors on
the wires coming from the switch housing,
install the wiring harness provided. Using
the provided wire connectors connect the
white wire from the fan to the white wire
from the wire harness and connect the
black or blue wire from the fan to the black
wire from the wire harness.
Wire
Connector
3
2
Switch
Housing
Screw
Using the switch housing screws that you
removed from the cap, install the adapter.
Adapter
4
Using the single pin connectors,
connect the black or blue wire from the
fan to the black wire from the light kit.
Connect the white wire from the fan to
the white wire from the light kit.
MA022-01 • 03/07/14
Adapter
Mounting
Screw
Lift the light kit up to meet the lower
switch housing. Using the mounting
screws found in the hardware bag,
install the light kit to the adapter.
4
Page 5
TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED)
1.888.830.1326
5
Bulb
Install a bulb into each of the sockets.
When necessary, replace with bulbs of
the same wattage.
7
6
Thumbscrews
Installing the globe - To install the globe,
rst loosen the thumbscrews. Raise the
globe to the light xture. Tighten all
thumbscrews securely.
8
Installing the pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
MA022-01 • 03/07/14
Turn Power
ON
Turn power on. Your
installation is complete!
5
Page 6
TYPE-B ASSEMBLY INSTRUCTIONS
21
1.888.830.1326
Switch
Housing
If your fan does not have pin connectors on
the wires coming from the switch housing,
install the wiring harness provided. Using
the provided wire connectors connect the
white wire from the fan to the white wire
from the wire harness and connect the
black or blue wire from the fan to the black
wire from the wire harness.
Mounting
Screw
Wire
Connector
Using the single pin connectors,
connect the black or blue wire from the
fan to the black wire from the light kit.
Connect the white wire from the fan to
the white wire from the light kit.
43
Lift the light kit up to meet the lower
switch housing. Using the mounting
screws found in the hardware bag,
install the light kit to the adapter.
6
MA022-01 • 03/07/14
Bulb
Install a bulb into each of the sockets.
When necessary, replace with bulbs of
the same wattage.
Do not allow the light kit to hang
only by the wire connections!
Page 7
TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED)
65
Thumbscrews
1.888.830.1326
Installing the globe - To install the globe,
rst loosen the thumbscrews. Raise the
globe to the light xture. Tighten all
thumbscrews securely.
7
Turn Power
ON
Turn power on. Your
installation is complete!
Installing the pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
7
MA022-01 • 03/07/14
Page 8
TYPE-C ASSEMBLY INSTRUCTIONS
1 2
1.888.830.1326
Feed the wires through the center hole in
the switch housing, the washer, and the
nut. Then install the switch housing by
twisting clockwise onto the threaded rod.
Install the washer and nut onto threaded
rod and tighten securely.
3
Switch
Housing
If your fan does not have pin connectors
on the wires coming from the switch
housing, install the wiring harness
provided. Using the provided wire
connectors connect the white wire from
the fan to the white wire from the wire
harness and connect the black or blue
wire from the fan to the black wire from
the wire harness.
Wire
Connector
4
Switch
Housing
Screw
Using the single pin connectors,
connect the black or blue wire from the
fan to the black wire from the light kit.
Connect the white wire from the fan to
the white wire from the light kit.
MA022-01 • 03/07/14
8
Lift the light kit assembly up so that the
screw holes in the lower switch housing
line up with the holes in the upper switch
housing. Install the switch housing
screws and tighten securely.
Do not allow the light kit to hang
only by the wire connections!
Page 9
TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED)
5 6
Thumbscrews
Bulb
1.888.830.1326
Install a bulb into each of the sockets.
When necessary, replace with bulbs of
the same wattage.
7
Installing the pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
Installing the globe - To install the globe,
rst loosen the thumbscrews. Raise the
globe to the light xture. Tighten all
thumbscrews securely.
8
Turn Power
ON
Turn power on. Your
installation is complete!
9
MA022-01 • 03/07/14
Page 10
TYPE-D ASSEMBLY INSTRUCTIONS
1 2
1.888.830.1326
Switch
Housing
If your fan does not have pin connectors on
the wires coming from the switch housing,
install the wiring harness provided. Using
the provided wire connectors connect the
white wire from the fan to the white wire
from the wire harness and connect the
black or blue wire from the fan to the black
wire from the wire harness.
Wire
Connector
3
Lower
Switch
Housing
Switch
Housing
Screw
Feed the wires through the center hole in
the switch housing. Then using the single
pin connectors, connect the black or blue
wire from the fan to the black wire from
the light kit. Connect the white wire from
the fan to the white wire from the light kit.
4
Threaded
Rod
Upper
Switch
Housing
Lift the lower switch housing up so that the
screw holes line up with the holes in the
upper switch housing. Install the switch
housing screws and tighten securely.
MA022-01 • 03/07/14
10
Lift the light kit up, tucking the wires into
the hole in the switch housing. Install the
center stem of the light kit into the lower
switch housing by turning the threaded
rod clockwise into the threaded hole.
Continue turning until tight.
Do not allow the light kit to hang
only by the wire connections!
Page 11
TYPE-D ASSEMBLY INSTRUCTIONS (CONTINUED)
5 6
Thumbscrews
Bulb
1.888.830.1326
Install a bulb into each of the sockets.
When necessary, replace with bulbs of
the same wattage.
7
Installing the pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
Installing the globe - To install the globe,
rst loosen the thumbscrews. Raise the
globe to the light xture. Tighten all
thumbscrews securely.
8
Turn Power
ON
Turn power on. Your
installation is complete!
11
MA022-01 • 03/07/14
Page 12
TROUBLESHOOTING
Lights don’t come on.
• Make sure that the bulbs are properly installed.
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Check the circuit breaker to ensure the power is turned on.
• Check the pin connections in the light kit.
• Refer to the fan manual for locating the fan’s wiring. Verify that the light and power wires are
correctly connected to the ceiling and the light kit.
2-YEAR ENERGY STAR LIGHT KIT WARRANTY
The Hunter Fan Company/Casablanca Fan Company makes the following warranty to
the original user or consumer purchaser of each Hunter/Casablanca Energy Efcient
Light Kit:
If your Hunter/Casablanca Energy Efcient Light Kit fails at any time within two years
after the date of sale due to a defect in material or workmanship, labor to repair the
defect will be provided free of charge at our nearest service center or our service
department in Memphis, TN. You will be responsible for all labor costs after this twoyear period.
This warranty is voided if this product is not purchased in the U.S.A. or Canada.
This warranty excludes and does not cover defects, malfunctions or failures of any
product which were caused by repairs by persons not authorized by us, use of parts or
accessories not authorized by us, mishandling, improper installation, modications or
damage to the light xture while in your possession, or unreasonable use, including
failure to provide reasonable and necessary maintenance. IN NO EVENT SHALL HUNTER
FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
1.888.830.1326
If you have problems installing or operating your light kit, do not return this product
to the dealer. Call our Consumer Affairs Hotline.
888-830-1326
12
MA022-01 • 03/07/14
Loading...