Page 1
Low Prole Integrated KitLow Prole Integrated Kit
Installation Manual
Models: 99153, 99154, 99155
Compatible with:
2xxxx Types A - Z
51000-58999 fan series
59500-59999 fan series
Select Casablanca Fans
MA021-01 • 03/06/14
Page 2
1.888.830.1326
BEFORE YOU BEGIN
Read entire installation instructions carefully before
beginning installation and save these instructions.
Switch
Housing
Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s
switch housing. Begin on page 3 where you will choose the type of switch housing that
most closely resembles the one on your fan. From there, you will be directed to the set of
assembly instructions that are appropriate for installing the light kit to your fan.
READ AND SAVE THESE INSTRUCTIONS
This product conforms to UL Standard 507.
WARNINGS
w.1 - To reduce the risk of re, electrical shock, or personal injury,
mount fan directly from building structure and/or an outlet box marked
acceptable for fan support of 70 lbs. (31.8 kg) and use the mounting screws
provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet
box and associated wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent warning device,
such as a tag, to the service panel.
CAUTIONS
c.1 - All wiring must be in accordance with national and local electrical codes
ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.
2
MA021-01 • 03/06/14
Turn Power
OFF
Page 3
1.888.830.1326
WHICH ASSEMBLY METHOD WILL I USE?
Choose one of the four images below that most closely resembles the switch
housing on your fan; then follow the instructions under the image.
Switch
Cap
Screw
If your fan’s switch housing cap
resembles this one, remove the cap
screws with a Phillips head screwdriver.
Then follow the TYPE-A ASSEMBLY
INSTRUCTIONS on pages 4-5.
Switch
Housing
Screw
Housing
Cap
Plug
Button
Switch
Housing
Screw
If your fan’s switch housing cap resembles
this one, remove the whole switch
housing by removing the switch housing
screws with a Phillips head screwdriver.
Remove the two cap screws from the
inside of the switch housing. Reinstall
the switch housing. Tighten the switch
housing screws. Then follow the TYPE-A
ASSEMBLY INSTRUCTIONS on pages 4-5.
Plug
Button
Switch
Housing
Cap
Switch
Housing
Screw
If your fan’s switch housing cap
resembles this one, remove the whole
switch housing by removing the switch
housing screws with a Phillips head
screwdriver. Remove the plug button.
Then follow the TYPE-B ASSEMBLY
INSTRUCTIONS on pages 6-7.
MA021-01 • 03/06/14
If your fan’s switch housing cap resembles
this one, remove the whole switch
housing by removing the switch housing
screws with a Phillips head screwdriver.
Remove the plug button using a standard
screwdriver. Then follow the TYPE-C
ASSEMBLY INSTRUCTIONS on pages 8-9.
3
Page 4
TYPE-A ASSEMBLY INSTRUCTIONS
1.888.830.1326
1
Partially install the two mounting
screws into the bottom of the
lower switch housing.
3
Mounting
Screw
2
Switch
Housing
If your fan does not have pin connectors
on the wires coming from the switch
housing, install the wiring harness
provided. Using the provided wire
connectors connect the white wire from
the fan to the white wire from the wire
harness and connect the black or blue
wire from the fan to the black wire from
the wire harness.
Wire
Connector
4
Using the single pin connectors, connect
the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire
from the light kit.
MA021-01 • 03/06/14
4
Mounting
Screw
Lift the light kit up to meet the
lower switch housing. Wrap keyhole
slots around the screws and twist
counterclockwise. Tighten screws.
Do not allow the light kit to hang
only by the wire connections!
Keyhole
Slots
Page 5
TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED)
1.888.830.1326
5
Bulb
Socket
Installing the bulbs - Install a bulb into each
of the sockets. When necessary, replace with
bulbs of same type and wattage.
7
6
Tab
Indentation
Installing the globe- Position the
indentations in the outer rim of the globe
so that they line up with the tabs on the
inside surface of the light xture rim.
Carefully lift the globe up inside the light
xture as far as it will go. Rotate the globe in
a clockwise direction until it is held tightly
in place by the four tabs.
8
Installing the pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
MA021-01 • 03/06/14
Turn Power
ON
Turn power on. Your installation
is complete!
5
Page 6
TYPE-B ASSEMBLY INSTRUCTIONS
1.888.830.1326
1
Switch
Housing
If your fan does not have pin connectors on
the wires coming from the switch housing,
install the wiring harness provided. Using
the provided wire connectors connect the
white wire from the fan to the white wire
from the wire harness and connect the
black or blue wire from the fan to the black
wire from the wire harness.
Wire
Connector
3
2
Feed the wires through the center hole in
the switch housing, the washer, and the
nut. Install the switch housing by twisting
clockwise onto the threaded rod. Install
the washer and nut onto threaded rod and
tighten securely.
4
Using the single pin connectors, connect
the black or blue wire from the fan to
the black wire from the light kit. Connect
the white wire from the fan to the white
wire from the light kit.
MA021-01 • 03/06/14
6
Switch
Housing
Screw
Lift the light kit assembly up so that the
screw holes in the lower switch housing
line up with the holes in the upper switch
housing. Install the switch housing
screws and tighten securely.
Do not allow the light kit to hang
only by the wire connections!
Page 7
TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED)
1.888.830.1326
5
Bulb
Socket
Installing the bulbs - Install a bulb into each
of the sockets. When necessary, replace with
bulbs of same type and wattage.
7
6
Tab
Indentation
Installing the globe- Position the
indentations in the outer rim of the globe
so that they line up with the tabs on the
inside surface of the light xture rim.
Carefully lift the globe up inside the light
xture as far as it will go. Rotate the globe in
a clockwise direction until it is held tightly
in place by the four tabs.
8
Installing the pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
MA021-01 • 03/06/14
Turn Power
ON
Turn power on. Your installation
is complete!
7
Page 8
TYPE-C ASSEMBLY INSTRUCTIONS
1.888.830.1326
1
Switch
Housing
If your fan does not have pin connectors on
the wires coming from the switch housing,
install the wiring harness provided. Using
the provided wire connectors connect the
white wire from the fan to the white wire
from the wire harness and connect the
black or blue wire from the fan to the black
wire from the wire harness.
Wire
Connector
3
Lower
Switch
Housing
Switch
Housing
Screw
2
Feed the wires through the center hole in
the switch housing. Then using the single
pin connectors, connect the black or blue
wire from the fan to the black wire from
the light kit. Connect the white wire from
the fan to the white wire from the light kit.
4
Upper
Switch
Housing
Threaded
Rod
Lift the lower switch housing up so that the
screw holes line up with the holes in the
upper switch housing. Install the switch
housing screws and tighten securely.
MA021-01 • 03/06/14
8
Lift the light kit up, tucking the wires into
the hole in the switch housing. Install the
center stem of the light kit into the lower
switch housing by turning the threaded
rod clockwise into the threaded hole.
Continue turning until tight.
Do not allow the light kit to hang
only by the wire connections!
Page 9
TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED)
1.888.830.1326
5
Bulb
Socket
Installing the bulbs - Install a bulb into each
of the sockets. When necessary, replace with
bulbs of same type and wattage.
7
6
Tab
Indentation
Installing the globe- Position the
indentations in the outer rim of the globe
so that they line up with the tabs on the
inside surface of the light xture rim.
Carefully lift the globe up inside the light
xture as far as it will go. Rotate the globe in
a clockwise direction until it is held tightly
in place by the four tabs.
8
Installing the pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
MA021-01 • 03/06/14
Turn Power
ON
Turn power on. Your installation
is complete!
9
Page 10
TROUBLESHOOTING
Lights don’t come on.
• Make sure that the bulbs are properly installed.
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Check the circuit breaker to ensure the power is turned on.
• Check the pin connections in the light kit.
• Refer to the fan manual for locating the fan’s wiring. Verify that the light and power
wires are correctly connected to the ceiling and the light kit.
ONE YEAR WARRANTY
1.888.830.1326
This product is warranted to the original purchaser by Casablanca Fan Company/
Hunter Fan Company against defects in material and workmanship for one (1)
year from date of purchase. During the warranty period, we will repair or, at our
option, replace a defective product at no charge. For information on how to obtain
service, contact the Casablanca/Hunter Service Department by calling our toll-
free number at 888-830-1326. Damage to the product caused by mishandling,
improper installation or modication is not covered by this warranty. This warranty
is given in lieu of all other warranties expressed or implied. Some states do not allow
limitations of time on an implied warranty, therefore the above limitations may not
apply in every case. This warranty states specic legal rights which may vary from
state to state.
If you have problems installing or operating your light kit, do not return this product
to the dealer. Call our Consumer Affairs Hotline.
888-830-1326
10
MA021-01 • 03/06/14
Loading...