Hunter 99023 User Manual

CFL Bowl FitterCFL Bowl Fitter

Installation Manual

Compatible with:
2xxxx Types A - Z
51000-58999 fan series
59500-59999 fan series
Select Casablanca Fans

MA003-01 • 07/24/13

Model 99023

1.888.830.1326

BEFORE YOU BEGIN

Read entire installation instructions carefully before

beginning installation and save these instructions.

Switch
Housing

Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s
switch housing. Begin on page 3 where you will choose the type of switch housing that
most closely resembles the one on your fan. From there, you will be directed to the set of
assembly instructions that are appropriate for installing the light kit to your fan.

READ AND SAVE THESE INSTRUCTIONS

This product conforms to UL Standard 507.

WARNINGS

w.1 - To reduce the risk of re, electrical shock, or personal injury,
mount fan directly from building structure and/or an outlet box marked
acceptable for fan support of 70 lbs. (31.8 kg) and use the mounting screws

provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet

box and associated wall switch location. If you cannot lock the circuit

breakers in the off position, securely fasten a prominent warning device,
such as a tag, to the service panel.

CAUTIONS

c.1 - All wiring must be in accordance with national and local electrical codes

ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.

2

MA003-01 • 07/24/13

Turn Power

OFF

1.888.830.1326

WHICH ASSEMBLY METHOD WILL I USE?

Choose one of the four images below that most closely resembles the switch
housing on your fan; then follow the instructions under the image.

Cap
Screw

If your fan’s switch housing cap

resembles this one, remove the cap

screws with a Phillips head screwdriver.

Then follow the TYPE-A ASSEMBLY

INSTRUCTIONS on pages 4-5.

Switch
Housing
Screw

Switch

Housing

Cap

Plug

Button

Switch
Housing
Screw

If your fan’s switch housing cap resembles

this one, remove the whole switch

housing by removing the switch housing

screws with a Phillips head screwdriver.

Remove the two cap screws from the

inside of the switch housing. Reinstall

the switch housing. Tighten the switch

housing screws. Then follow the TYPE-A

ASSEMBLY INSTRUCTIONS on pages 4-5.

Plug
Button

Switch

Housing

Cap

Switch

Housing

Screw

If your fan’s switch housing cap

resembles this one, remove the whole

switch housing by removing the switch

housing screws with a Phillips head

screwdriver. Remove the plug button.

Then follow the TYPE-B ASSEMBLY

INSTRUCTIONS on pages 6-7.

MA003-01 • 07/24/13

If your fan’s switch housing cap resembles

this one, remove the whole switch

housing by removing the switch housing

screws with a Phillips head screwdriver.

Remove the plug button using a standard

screwdriver. Then follow the TYPE-C

ASSEMBLY INSTRUCTIONS on pages 8-9.

3

TYPE-A ASSEMBLY INSTRUCTIONS

1 2

1.888.830.1326

Switch
Housing

If your fan does not have pin connectors on

the wires coming from the switch housing,

install the wiring harness provided. Using

the provided wire connectors connect the

white wire from the fan to the white wire

from the wire harness and connect the

black or blue wire from the fan to the black

wire from the wire harness.

Wire

Connector

3 4

Light Kit
Screw

Using the single pin connectors, connect

the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire

from the light kit.

Fan Pull

Chain

Grommeted

Hole

Lift the light kit up to meet the lower

switch housing. Install the two light kit

screws. Tighten screws.

MA003-01 • 07/24/13

4

Light Pull
Chain

If necessary, attach the extension chain

provided to the fan pull chain coming
from the switch housing. Then feed the
end of the extension chain through the

grommeted hole in the light kit.

Do not allow the light kit to hang
only by the wire connections!

TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED)

65

Globe

1.888.830.1326

Socket

Installing the bulb - Install a bulb into each

socket. When necessary, replace bulbs with

bulbs of same type and wattage.

7

Globe
Keeper

Finial Cap

Finial

Installing the globe - Press the globe

and globe keeper ush against the metal

plate. Thread the light pull chain through

the hole in the center of the nial cap

and thread the fan pull chain through

the hole in the side of the cap. Finally,

thread only the light pull chain through

the hole in the nial and screw the nial

onto the threaded rod.

Installing the Pull chain pendant -

Attach the pull chain pendants to the
end of the short chains coming from the
switch housing and the light kit. Turn on

power. Your installation is complete!

MA003-01 • 07/24/13

5

TYPE-B ASSEMBLY INSTRUCTIONS

1 2

Switch
Housing

Wire

Connector

1.888.830.1326

Switch

Housing

Light Kit

Screw

If your fan does not have pin connectors on

the wires coming from the switch housing,

install the wiring harness provided. Using

the provided wire connectors connect the

white wire from the fan to the white wire

from the wire harness and connect the

black or blue wire from the fan to the black

wire from the wire harness.

3 4

Using the single pin connectors, connect

the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire

from the light kit.

line up with the holes in the upper switch

Feed the light kit wires through the

center hole in the switch housing. Then

attach the switch housing to the light kit

by installing the light kit screws into the

bottom of the switch housing.

Switch
Housing
Screw

Lift the light kit assembly up so that the

screw holes in the lower switch housing

housing. Install the switch housing

screws and tighten securely.

6

MA003-01 • 07/24/13

Do not allow the light kit to hang
only by the wire connections!

TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED)

65

Fan Pull

Chain

1.888.830.1326

Grommeted

Hole

Light Pull
Chain

If necessary, attach the extension chain

provided to the fan pull chain coming
from the switch housing. Then feed the
end of the extension chain through the

grommeted hole in the light kit.

7 8

Globe

Globe
Keeper

Finial Cap

Socket

Installing the bulb - Install a bulb

into each socket. When necessary,

replace bulbs with bulbs of same

type and wattage.

Finial

Installing the globe - Press the globe and

globe keeper ush against the metal plate.

Thread the light pull chain through the hole

in the center of the nial cap and thread

the fan pull chain through the hole in the

side of the cap. Finally, thread only the light
pull chain through the hole in the nial and

screw the nial onto the threaded rod.

MA003-01 • 07/24/13

Installing the pull chain pendant -

Attach the pull chain pendants to the

end of the short chains coming from the

switch housing and the light kit. Turn

power on. Your installation is complete.

7

TYPE-C ASSEMBLY INSTRUCTIONS

1 2

1.888.830.1326

Washer
and Nut

Threaded

Rod

Switch

Housing

If your fan does not have pin connectors on

the wires coming from the switch housing,

install the wiring harness provided. Using

the provided wire connectors connect the

white wire from the fan to the white wire

from the wire harness and connect the

black or blue wire from the fan to the black

wire from the wire harness.

Wire

Connector

3 4

Feed the wires through the switch

housing cap, washer, and nut. Then

install the switch housing cap by twisting

clockwise onto the threaded rod. Install

the washer and nut onto threaded rod

and tighten securely.

Upper
Switch
Housing

Using the single pin connectors, connect

the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire

from the light kit.

MA003-01 • 07/24/13

8

Lift the light kit assembly up so that the
screw holes in the lower switch housing

line up with the holes in the upper switch

housing. Install the switch housing

screws and tighten securely.

Do not allow the light kit to hang
only by the wire connections!

TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED)

65

Fan Pull

Chain

1.888.830.1326

Grommeted

Hole

Light Pull

Chain

If necessary, attach the extension chain

provided to the fan pull chain coming
from the switch housing. Then feed the
end of the extension chain through the

grommeted hole in the light kit.

7 8

Globe

Globe
Keeper

Finial Cap

Socket

Installing the bulb - Install a bulb

into each socket. When necessary,

replace bulbs with bulbs of same

type and wattage.

Finial

Installing the globe - Press the globe and

globe keeper ush against the metal plate.

Thread the light pull chain through the hole

in the center of the nial cap and thread

the fan pull chain through the hole in the

side of the cap. Finally, thread only the light
pull chain through the hole in the nial and

screw the nial onto the threaded rod.

MA003-01 • 07/24/13

Installing the pull chain pendant -

Attach the pull chain pendants to the

end of the short chains coming from the

switch housing and the light kit. Turn

power on. Your installation is complete.

9

TROUBLESHOOTING

Lights don’t come on.

• Make sure that the bulbs are properly installed.

• Make sure power switch is on.

• Pull the pull chain to make sure it is on.

• Check the circuit breaker to ensure the power is turned on.

• Check the pin connections in the light kit.

• Refer to the fan manual for locating the fan’s wiring. Verify that the light and power

wires are correctly connected to the ceiling and the light kit.

ONE YEAR WARRANTY

1.888.830.1326

This product is warranted to the original purchaser by Casablanca Fan Company/
Hunter Fan Company against defects in material and workmanship for one (1)
year from date of purchase. During the warranty period, we will repair or, at our
option, replace a defective product at no charge. For information on how to obtain
service, contact the Casablanca/Hunter Service Department by calling our toll-
free number at 888-830-1326. Damage to the product caused by mishandling,
improper installation or modication is not covered by this warranty. This warranty

is given in lieu of all other warranties expressed or implied. Some states do not allow

limitations of time on an implied warranty, therefore the above limitations may not
apply in every case. This warranty states specic legal rights which may vary from

state to state.

If you have problems installing or operating your light kit, do not return this product

to the dealer. Call our Consumer Affairs Hotline.

888-830-1326

Monday through Friday

8:00 am to 4:30 pm Central

10

MA003-01 • 07/24/13