Page 1
11
1
11
© 2002 Hunter Fan Company 41803-01 11/14/2002
Page 2
22
2
22
®
Your new Hunter® ceiling fan is an addition to your home or office
that will provide comfort and performance for many years. This
installation and operation manual gives you complete instructions
for installing and operating your fan.
We are proud of our work. We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.
Before installing your fan, record the following information for your
records and warranty assistance. Please refer to the carton and the
Hunter nameplate label (located on the top of the fan motor housing) for the proper information.
Model Name: __________________________
Catalog/Model No.: ______________
Serial No.: _____________________
Date Purchased: ___ / ___ / ______
Where Purchased: _______________________________
Please also attach your receipt or a copy of your receipt for reference.
Easy LockTM Blade System
Your new Hunter ceiling fan includes our exclusive Easy LockTM blade
assembly which locks the blades in place without tools and eliminates up to 40 parts. It also allows easy removal of the blades for
cleaning.
getting ready
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician.
gathering the tools
You will need the following tools for installing the fan:
• Electric drill with 9/64" bit
• Standard screwdriver
• Phillips-head screwdriver
• Wrench or pliers
considering optional accessories
Consider using Hunter’s optional accessories, including a wallmounted or remote speed control. To install and use the accessories, follow the instructions included with each product. For quiet
and optimum performance of your Hunter fan, use only Hunter
speed controls.
checking your fan parts
cautions and warnings
••
RR
ee
aa
d ed e
nn
tt
irir
e be b
oo
oo
kk
ll
ee
hh
h
hh
hh
h
hh
hh
h
hh
ee
e
ee
cc
c
cc
rr
s ts t
r
s t
rr
s ts t
ii
i
ii
ff
f
ff
ii
i
ii
cc
c
cc
ii
i
ii
inin
in
inin
hh
h
hh
e oe o
e o
e oe o
d.d.
d.
d.d.
ss
s
ss
oo
o
oo
f pf p
f p
f pf p
cc
c
cc
aa
a
aa
tt
t
tt
e re r
e r
e re r
hh
h
hh
e re r
e r
e re r
o
oo
hh
h
hh
tt
t
tt
e re r
e r
e re r
e se s
e s
e se s
ee
e
ee
sibsib
sib
sibsib
oo
o
oo
nn
n
nn
ee
e
ee
ss
s
ss
l cl c
l c
l cl c
h wh w
h w
h wh w
e fe f
e f
e fe f
g fg f
g f
g fg f
oo
o
oo
o
oo
ee
e
ee
ee
e
ee
ss
s
ss
nnnn
nn
nnnn
o to t
o t
o to t
, s
t bt b
t b
t bt b
ii
i
ii
ee
e
ee
t ut u
t u
t ut u
nlnl
nl
nlnl
k
kk
ss
s
ss
r rr r
r r
r rr r
ii
ss
i
s
ii
ss
upup
up
upup
e ine in
e in
e ine in
ll
l
ll
. I. I
. I
. I. I
oo
o
oo
, s, s
, s, s
o
ss
k ok o
s
k o
ss
k ok o
nn
n
nn
aa
a
aa
ii
ss
i
s
ii
ss
t ct c
l
e
t c
ll
ee
t ct c
e ine in
e in
e ine in
ee
pp
e
p
ee
pp
k ok o
k o
k ok o
e ee e
e e
e ee e
ee
cc
e
c
ee
cc
hh
h
hh
f yf y
f y
f yf y
sisi
tt
si
t
sisi
tt
uu
cc
u
c
uu
cc
e in ae in a
e in a
e in ae in a
oo
dd
d
oo
dd
irir
inin
ir
in
irir
inin
t st s
t s
t st s
aa
nn
a
n
aa
nn
n bn b
n b
n bn b
k ok o
k o
k ok o
ss
s
e a s
ss
y Hy H
y H
y Hy H
•
R
e
a
d e
n
t
ir
••
RR
ee
aa
ll
aa
tt
ii
l
a
t
i
ll
aa
tt
ii
••
UsUs
e oe o
•
Us
e o
••
UsUs
e oe o
••
TT
o ro r
•
T
o r
••
TT
o ro r
dirdir
ee
dir
e
dirdir
ee
cc
oo
rr
c
o
r
cc
oo
rr
ww
aa
rr
w
a
r
ww
aa
rr
••
TT
o ao a
•
T
o a
••
TT
o ao a
yy
oo
ur fur f
y
o
ur f
yy
oo
ur fur f
cc
uiui
c
ui
cc
uiui
ss
ww
ii
s
w
i
ss
ww
ii
ee
rr
s in ts in t
e
r
s in t
ee
rr
s in ts in t
ww
aa
rr
w
a
r
ww
aa
rr
••
AA
ll wll w
•
A
ll w
••
AA
ll wll w
ll
oo
cc
l
o
c
ll
oo
cc
unun
ff
un
f
unun
ff
tt
rr
ii
cc
t
r
i
c
tt
rr
ii
cc
••
TT
o ro r
•
T
o r
••
TT
o ro r
bb
ll
aa
b
l
a
bb
ll
aa
oo
r cr c
o
r c
oo
r cr c
tt
ww
ee
t
w
e
tt
ww
ee
••
TT
o ro r
•
T
o r
••
TT
o ro r
dd
aa
mm
d
a
m
dd
aa
mm
tt
hh
ii
s fs f
t
h
i
s f
tt
hh
ii
s fs f
d ed e
oo
o
oo
ee
e
ee
cc
c
cc
dindin
din
dindin
e se s
e s
e se s
t bt b
t b
t bt b
tt
cc
t
c
tt
cc
nn
n
nn
aa
l el e
a
l e
aa
l el e
aa
a
aa
ii
aa
i
a
ii
aa
ee
e
ee
dd
d
e a
dd
ll
l
ll
ee
e
ee
ee
e
ee
nn
n
nn
dudu
du
dudu
tt
t
tt
vv
v
vv
h lh l
h l
h lh l
inin
in
inin
irir
ir
irir
mm
m
mm
nn
n
nn
dudu
du
dudu
e ae a
e ae a
ee
e
ee
n rn r
n r
n rn r
dudu
du
dudu
aa
a
aa
aa
a
aa
. S. S
. S
. S. S
nlnl
nl
nlnl
ll
l
ll
oo
o
oo
aa
a
aa
r
aa
a
aa
gg
g
gg
nn
n
nn
nn
y Hy H
y H
y Hy H
y ty t
y t
y ty t
g tg t
g t
g tg t
upup
up
upup
ii
d pd p
i
d p
ii
d pd p
nn
n
nn
rr
ee
e
rr
ee
o
hh
h
hh
g dg d
g d
g dg d
inin
in
inin
ll
ee
l
e
ll
ee
iliili
ili
iliili
..
.
..
cc
c
cc
tt
t
tt
nn
n
nn
oo
o
oo
ee
e
ee
. Us. Us
. Us
. Us. Us
tt
irir
aa
vv
a
v
aa
vv
cc
e te t
c
e t
cc
e te t
o to t
o t
o to t
o to t
o t
o to t
pp
p
pp
, di, di
, di
, di, di
aa
kk
a
k
aa
kk
oo
cc
c
oo
cc
e oe o
e o
e oe o
e
g mug mu
g mu
g mug mu
cc
tt
c
t
cc
tt
aa
r wr w
a
r w
aa
r wr w
e te t
e t
e te t
tt
aa
t
a
c
tt
aa
inin
g tg t
in
g t
inin
g tg t
tt
aa
t
a
tt
aa
cc
e te t
c
e t
cc
e te t
, d, d
, d
, d, d
e b
e be b
e te t
e t
e te t
unun
un
unun
lili
li
lili
oo
o
oo
ss
s
ss
ee
e
ee
aa
tt
a
t
aa
tt
ee
vv
v
ee
vv
rr
ii
r
i
rr
ii
hh
h
hh
cc
hmhm
hm
cc
hmhm
tt
t
tt
o no n
o n
o no n
aa
a
aa
ss
tt
s
t
ss
tt
ll
aa
l
a
ll
aa
f pf p
f p
f pf p
pp
oo
p
o
pp
oo
ss
tt
rr
s
t
r
ss
tt
rr
ll
ee
l
e
ll
ee
t tt t
t t
t tt t
e oe o
e o
e oe o
oo
u cu c
o
u c
oo
u cu c
ii
oo
nn
i
o
n
ii
oo
nn
h ah a
h a
h ah a
ee
s as a
e
s a
ee
s as a
gg
g
gg
f pf p
f p
f pf p
yy
ss
tt
y
s
t
yy
ss
tt
. N. N
. N
. N. N
ll
aa
l
a
ll
aa
f ff f
f f
f ff f
e a se a s
e a se a s
unun
un
unun
rr
r
rr
rr
uu
r
u
rr
uu
cc
ee
c
e
cc
ee
rr
t st s
r
t s
rr
t st s
uu
cc
u
c
uu
cc
cc
tt
c
t
cc
tt
hh
e pe p
h
e p
hh
e pe p
uu
u
uu
, s, s
, s
, s, s
s a ts a t
s a t
s a ts a t
n
, y, y
, y
, y, y
ee
e
ee
ee
e
ee
ee
e
ee
dd
d
dd
irir
ir
irir
tt
t
tt
ee
ff
ullull
e
f
ull
ee
ff
ullull
cc
tt
c
t
cc
tt
mm
m
mm
ee
rr
ss
e
r
s
ee
rr
ss
tt
t
tt
tt
ii
oo
t
i
o
tt
ii
oo
rr
ii
cc
r
i
c
rr
ii
cc
tt
ll
ee
t
l
e
tt
ll
ee
aa
nnnn
a
nn
aa
nnnn
ee
e
ee
cc
cc
c
c
cc
cc
nn
d Ad A
d A
nn
d Ad A
oo
u su s
o
u s
oo
u su s
rr
ss
oo
r
s
o
rr
ss
oo
m wm w
m w
m wm w
vv
ee
v
e
vv
ee
ee
ss
e
s
.
ee
ss
ee
, e, e
e
, e
ee
, e, e
oo
lili
o
li
oo
lili
ee
r sr s
e
r s
ee
r sr s
ii
oo
i
o
ii
oo
ee
e
ee
oo
o
oo
rr
uu
r
u
rr
uu
nn
n
nn
aa
a
aa
oo
o
oo
t bt b
t b
t bt b
cc
c
cc
aa
a
aa
oo
o
oo
nn
n
nn
r inr in
r in
r inr in
..
..
d-d-
d-
d-d-
pp
p
pp
y by b
y b
y by b
nn
n
nn
nn
n
nn
l sl s
l s
l sl s
ww
w
ww
urur
ur
urur
gg
g
gg
rr
r
rr
hh
h
hh
aa
a
aa
ll
l
ll
dd
d
dd
NN
N
NN
hh
h
hh
ss
s
ss
nn
n
nn
t pt p
t p
t pt p
cc
c
cc
ss
s
ss
oo
o
oo
ee
e
ee
ee
e
ee
ss
s
ss
aa
l inl in
a
l in
aa
l inl in
tt
urur
t
ur
tt
urur
, a, a
, a
, a, a
hh
h
hh
ee
e
ee
oo
o
oo
t lt l
t l
t lt l
ee
e
ee
, t, t
, t
, t, t
aa
a
aa
SS
S
SS
oo
o
oo
l inl in
l in
l inl in
ee
e
ee
ss
s
ss
cc
c
cc
tt
aa
t
a
tt
aa
ee
e
ee
ee
ff
e
f
ee
ff
..
.
..
aa
a
aa
nn
n
nn
oo
o
oo
r br b
r b
r br b
x ax a
x a
x ax a
oo
o
oo
ll
y fy f
l
y f
ll
y fy f
o to t
o t
o to t
nn
cc
n
c
nn
cc
I/NI/N
I/N
I/NI/N
ulul
d ud u
ul
d u
ulul
d ud u
jurjur
jur
jurjur
n inn in
n in
n inn in
ee
rr
e
r
ee
rr
tt
rr
ii
t
r
i
tt
rr
ii
tt
e se s
t
e s
tt
e se s
d cd c
d c
d cd c
oo
rr
o
r
oo
rr
rr
tt
r
t
rr
tt
jurjur
jur
jurjur
e oe o
e o
e oe o
d ud u
d u
d ud u
cc
kk
c
k
cc
kk
y ty t
y t
y ty t
cc
c
cc
hh
h
hh
e we w
e w
e we w
t ft f
t f
t ft f
cc
c
cc
oo
o
oo
e be b
e b
e be b
ss
..
s
.
ss
..
yy
y
yy
f tf t
f t
f tf t
ss
e oe o
s
e o
ss
e oe o
, b, b
, b
, b, b
urur
ur
urur
nn
d ad a
n
d a
nn
d ad a
k tk t
hh
k t
h
k tk t
hh
aa
ss
tt
ee
a
s
t
e
aa
ss
tt
ee
e se s
e s
e se s
ii
i
ii
FF
PP
A 70. IA 70. I
F
P
A 70. I
FF
PP
A 70. IA 70. I
ss
e a qe a q
s
e a q
ss
e a qe a q
yy
, d, d
y
, d
yy
, d, d
ss
tt
aa
s
t
a
ss
tt
aa
oo
rr
ee
o
r
e
oo
rr
ee
aa
l sl s
a
l s
aa
l sl s
pp
ee
p
e
pp
ee
nn
tt
rr
n
t
r
nn
tt
rr
ee
gg
inninn
e
g
inn
ee
gg
inninn
, a, a
tt
, a
t
, a, a
tt
hh
e be b
h
e b
hh
e be b
nlnl
nl
nlnl
ee
ff
oo
e
f
o
ee
ff
oo
nn
inin
n
in
nn
inin
ss
ss
s
s
ss
ss
e ce c
e c
e ce c
n a pn a p
n a p
n a pn a p
ee
rr
vv
e
r
v
ee
rr
vv
tt
h nh n
t
h n
tt
h nh n
o no n
o n
o no n
llinllin
llin
llinllin
ii
gg
n on o
i
g
n o
ii
gg
n on o
hh
oo
cc
h
o
c
hh
oo
cc
ee
d cd c
e
d c
ee
d cd c
oo
ll
ss
o
l
s
oo
ll
ss
tt
t
tt
rr
r
rr
g og o
g o
g og o
oo
o
oo
irir
ir
irir
ii
i
ii
uu
u
uu
gg
g
gg
kk
k
kk
..
.
..
inin
in
inin
aa
cc
a
c
aa
cc
uiluil
uil
uiluil
y ty t
y t
y ty t
e ine in
e in
e ine in
cc
ii
c
i
cc
ii
cc
c
ui
cc
cc
e pe p
c
e p
cc
e pe p
aa
tt
a
t
aa
tt
aa
lili
a
li
aa
lili
oo
t bt b
o
t b
oo
t bt b
, b, b
, b
, b, b
bb
b
bb
, o, o
, o
, o, o
oo
nn
o
n
oo
nn
h th t
h t
h th t
ff
f
ff
aa
a
aa
uiui
uiui
rr
r
rr
ii
i
o
ii
f yf y
f y
f yf y
a
hh
h
hh
f tf t
f t
f tf t
tt
t
tt
oo
o
oo
oo
oo
ff
f
ff
aa
aa
jj
j
jj
tt
t
tt
g ing in
g in
g ing in
hh
h
hh
dindin
din
dindin
e he h
e h
e he h
ss
tt
s
t
ss
tt
hh
h
hh
ee
d wd w
e
d w
ee
d wd w
t bt b
t b
t bt b
mm
m
mm
aa
nn
a
n
aa
nn
nn
aa
n
a
nn
aa
oo
o
oo
ii
ee
d ed e
i
e
d e
ii
ee
d ed e
ee
nn
e
n
ee
nn
ll
aa
l
a
ll
aa
ee
cc
e
c
ee
cc
r mr m
r m
r mr m
rr
oo
r
o
rr
oo
aa
a
aa
inin
in
inin
l al a
l a
l al a
u au a
u a
u au a
d td t
d t
d td t
nn
n
nn
tt
t
tt
l wl w
l w
l wl w
ss
s
ss
e fe f
e f
e fe f
g ag a
g a
g ag a
llinllin
llin
llinllin
e ce c
e c
e ce c
rr
r
e
rr
ee
e
ee
cc
c
cc
s bs b
s b
s bs b
oo
o
oo
Carefully unpack your fan to avoid damage to the fan parts. Check
tt
aa
l-l-
t
a
l-
tt
aa
l-l-
aa
nn
a
n
aa
nn
cc
--
c
-
cc
--
aa
rr
d-d-
a
r
d-
aa
rr
d-d-
gg
g
gg
irir
--
ir
-
irir
--
aa
llll
a
ll
aa
llll
ee
aa
kk
--
a
k
-
ee
aa
kk
--
ee
nn
tt
e
n
t
ee
nn
tt
l.l.
l.
l.l.
nn
dd
n
d
nn
dd
rr
ee
r
e
rr
ee
ll
ee
cc
--
l
e
c
-
ll
ee
cc
--
hh
ee
h
e
hh
ee
inin
gg
,,
in
g
,
inin
gg
,,
e-e-
e-
e-e-
tt
oo
rr
t
o
r
tt
oo
rr
ii
tt
hh
i
t
h
ii
tt
hh
for any shipping damage to the motor or fan blades. If one of the
fan blades was damaged in shipment, return all the blades for replacement.
NOTE: If you are installing more than one fan, keep the fan blades
in sets, as they were shipped.
If any parts are missing or damaged, contact your Hunter dealer or
call Hunter Parts Department at 888-830-1326.
understanding Installer’s Choice
ss
h mh m
s
h m
ss
h mh m
®
10”
oo
unun
tt
inin
gg
o
un
t
in
g
oo
unun
tt
inin
gg
This patented 3-position mounting system provides you maximum
installation flexibility and ease. You can install your Hunter fan in
one of three ways. The steps in this manual include specific instructions for the fan mounting method of your choice. For a ceiling 8
feet or higher, standard mounting is recommended.
FF
lulu
ss
h Mh M
oo
unun
tt
inin
F
lu
s
h M
FF
lulu
ss
h Mh M
less than 8 feet high.
gg
o
un
t
in
g (Figure 1) fits close to the ceiling, for low ceilings
oo
unun
tt
inin
gg
FF
ii
gg
urur
e 1 - Fe 1 - F
e 1 - F
e 1 - Fe 1 - F
lulu
lu
lulu
F
i
g
ur
FF
ii
gg
urur
41803-01 11/14/2002 © 2002 Hunter Fan Company
Page 3
SS
tt
aa
nn
dd
aa
rr
d Md M
oo
unun
tt
inin
S
t
a
n
d
a
r
SS
d M
tt
aa
nn
dd
aa
rr
d Md M
gg
o
un
t
in
g (Figure 2) hangs from the ceiling by a downrod
oo
unun
tt
inin
gg
(included), for ceilings 8 feet or higher. For ceilings higher than 8
feet, you can purchase Hunter extension downrods. All Hunter
fans use sturdy 3/4" diameter pipe to assure stability and wobblefree performance.
8’ Minimum
Ceiling Height
30” From
Wall or
Nearest
Obstruction
33
3
33
12”
FF
ii
gg
urur
e 2 - Se 2 - S
tt
aa
nn
dd
aa
rr
d md m
oo
unun
tt
inin
F
i
g
ur
e 2 - S
t
a
n
d
a
r
FF
ii
gg
urur
e 2 - Se 2 - S
AA
nn
gg
ll
e Me M
oo
unun
tt
inin
A
n
g
l
e M
AA
nn
gg
ll
e Me M
gg
o
un
t
in
g (Figure 3) hangs from a vaulted or angled ceiling.
oo
unun
tt
inin
gg
FF
ii
gg
urur
e 3 - Ae 3 - A
F
i
g
ur
e 3 - A
FF
ii
gg
urur
e 3 - Ae 3 - A
d m
tt
aa
nn
dd
aa
rr
d md m
nn
gg
ll
e me m
n
g
l
e m
o
nn
gg
ll
e me m
o
oo
oo
unun
un
oo
unun
un
t
in
unun
tt
inin
34º Max
Pitch
12
tt
inin
gg
t
in
g
tt
inin
gg
gg
g
gg
8
preparing the fan site
These guidelines are designed to help you select the best location
for your fan and to prepare the site prior to installing the fan. Proper
ceiling fan location and attachment to the building structure are
essential for safety, reliable operation, maximum efficiency, and energy savings.
choosing the fan site
Within the room where you want to install the fan, choose a fan
site where:
• No object can come in contact with the rotating fan blades
during normal operation.
• The fan blades are at least 7 feet above the floor and the
ceiling is at least 8 feet high.
• The fan blades have no obstructions to air flow, such as
walls or posts, within 30 inches of the fan blade tips.
• The fan is directly below a joist or support brace that will
hold the outlet box and the full weight of the fan.
See Figure 4 for the minimum mounting distances.
7’ Minimum
to Floor
FF
ii
gg
urur
e 4 - Me 4 - M
inin
F
i
g
ur
e 4 - M
FF
ii
gg
urur
e 4 - Me 4 - M
imum mimum m
in
imum m
inin
imum mimum m
oo
unun
tt
inin
g dig di
ss
tt
aa
nn
cc
ee
o
un
t
in
g di
oo
unun
tt
inin
g dig di
ss
s
t
a
n
c
e
s
ss
tt
aa
nn
cc
ee
ss
using an existing fan site
pp
rr
ee
pp
aa
rr
inin
g a ng a n
ee
w fw f
n sin si
n si
n sin si
e
w f
ee
w fw f
tt
ee
t
e sec-
tt
ee
aa
a
aa
If you are preparing a new fan site, go to the
sisi
tt
ee
si
t
e section.
sisi
tt
ee
p
r
e
p
a
r
in
pp
g a n
rr
ee
pp
aa
rr
inin
g a ng a n
If you plan to use an existing fan site, complete the following checklist for the support brace, ceiling hole, outlet box, and wiring. If you
pp
rr
ee
pp
aa
rr
inin
g a ng a n
ee
w fw f
cannot check off every item, see the
p
r
e
p
a
r
in
pp
g a n
rr
ee
pp
aa
rr
inin
g a ng a n
e
ee
w f
w fw f
aa
a
aa
tion for instructions on properly preparing the site for your new
fan.
fan support system
• Fan must attach directly to building structure.
• Fan support system must hold full weight of fan and light
kit.
ceiling hole
• Outlet box clearance hole directly below the joist or support brace.
outlet box
• UL-approved octagonal 4" x 1-1/2" outlet box (or as specified by the support brace manufacturer).
• Outlet box secured to joist or support brace by wood
screws and washers through inner holes of outlet box.
• Outer holes of outlet box aligned with joist or support
brace.
• Bottom of outlet box recessed a minimum of 1/16" into
ceiling.
nn
n
nn
© 2002 Hunter Fan Company 41803-01 11/14/2002
Page 4
44
4
44
wiring
• Electrical cable secured to outlet box by approved connector.
• Six inches of lead wires extend from outlet box.
See Figure 5 for an adequate existing fan site.
Support Brace
Washer
Wood Screw
FF
ii
gg
urur
e 5 - Ae 5 - A
dd
e 5 - A
e 5 - Ae 5 - A
ee
d
e
dd
ee
F
i
g
ur
FF
ii
gg
urur
If your existing fan site is suitable, go to the
pp
ll
aa
tt
ee
p
l
a
t
e section and begin installing your new Hunter fan.
pp
ll
aa
tt
ee
Approved
Connector
qq
uu
aa
q
u
a
qq
uu
aa
Ceiling Joist
tt
e exe ex
t
e ex
tt
e exe ex
Outlet Box
ii
ss
tt
inin
g fg f
i
s
t
in
g f
ii
ss
tt
inin
g fg f
aa
a
aa
inin
in
inin
Ceiling
n sin si
n si
n sin si
ss
s
ss
tt
ee
t
e
tt
ee
tt
aa
llinllin
g tg t
t
a
llin
g t
tt
aa
llinllin
g tg t
preparing a new fan site
1. Attach a 2" x 4" support brace between two joists. The support brace must allow the bottom of the outlet box to be recessed a minimum of 1/16" into the ceiling. See Figure 7.
2. Check the support brace to ensure it will support the full weight
of the fan and light kit.
installing the outlet box
1. Obtain a UL-approved octagonal 4" x 1-1/2" outlet box, plus
two #8 x 1-1/2" wood screws and washers, available from any
hardware store or electrical supply house.
2. Orient the outlet box so that both the inner and outer holes in
the box align with the joist or support brace.
3. Drill pilot holes no larger than the minor diameter of the wood
screws (5/64") through the inner holes of the outlet box.
4. Attach the outlet box directly to the support brace or joist
with two #8 x 1-1/2" wood screws and washers. The bottom of
the outlet box must be recessed a minimum of 1/16" into the
ceiling as shown in Figure 7.
Support Brace
hh
e ce c
ee
ilinilin
e c
e ce c
e
ee
ilin
ilinilin
gg
g
gg
h
hh
To prepare the fan site follow four steps:
• Cutting the Ceiling Hole
• Installing the Support Brace (if necessary)
• Installing the Outlet Box
• Preparing the Wiring
cutting the ceiling hole
1. Locate the site for the hole directly below the joist or support
brace that will hold the outlet box and fan.
2. Cut a 4" diameter hole through the drywall or plaster of the
ceiling as shown in Figure 6. You will use the hole to install the
support brace and outlet box.
Support Brace
Ceiling Joist
4”
Diameter
Ceiling
Hole
Ceiling
Washer
Wood Screw
FF
ii
gg
urur
e 7 - Ie 7 - I
F
i
g
ur
e 7 - I
FF
ii
gg
urur
e 7 - Ie 7 - I
nn
ss
tt
aa
llinllin
n
s
t
a
llin
nn
ss
tt
aa
llinllin
g tg t
g t
g tg t
hh
h
hh
Outlet Box
1/16” Recess
e oe o
uu
tt
ll
ee
t bt b
e o
u
t
l
e
t b
e oe o
uu
tt
ll
ee
t bt b
oo
xx
o
x
oo
xx
preparing the wiring
CC
AA
UU
TT
II
OO
N: AN: A
ll wll w
irir
inin
g mug mu
ss
t bt b
e in ae in a
cc
cc
oo
rr
dd
aa
nn
cc
e we w
ii
tt
C
A
U
T
I
O
N: A
ll w
ir
in
g mu
s
t b
e in a
c
c
o
r
d
a
n
cc
cc
oo
rr
dd
aa
nn
NN
SS
I/NI/N
FF
PP
N
S
I/N
F
P
NN
SS
I/NI/N
FF
PP
ss
e a qe a q
s
e a q
u
ss
e a qe a q
tt
t
tt
aa
a
aa
tt
t
tt
CC
ii
oo
i
o
ii
oo
rr
e une un
r
e un
rr
e une un
rr
ii
cc
r
i
c
rr
ii
cc
AA
UU
TT
II
OO
N: AN: A
ll wll w
irir
inin
g mug mu
ss
t bt b
e in ae in a
nn
aa
l al a
nn
d ld l
oo
cc
aa
l el e
ll
ee
cc
tt
rr
ii
cc
aa
l cl c
oo
dd
ee
s as a
nn
n
a
l a
n
d l
o
c
a
l e
l
e
c
t
r
i
c
a
l c
nn
aa
l al a
nn
d ld l
oo
cc
aa
l el e
ll
ee
cc
ff
aa
mm
iliili
aa
r wr w
ii
tt
a
aa
r w
r wr w
i
ii
t
tt
h wh w
h w
h wh w
f
a
m
ili
ff
aa
mm
iliili
ii
aa
nn
..
i
a
n
.
ii
aa
nn
..
o
tt
rr
ii
cc
aa
l cl c
oo
irir
inin
gg
, y, y
ir
in
g
, y
irir
inin
gg
, y, y
d Ad A
d
e
s a
n
d A
dd
ee
s as a
nn
d Ad A
oo
u su s
hh
oo
ulul
u s
u su s
d ud u
h
o
ul
d u
hh
oo
ulul
d ud u
o
oo
1. Make sure the circuit breakers to the fan supply line leads and
associated wall switch location are turned off. If you cannot
lock the circuit breakers in the off position, securely fasten a
prominent warning device, such as a tag, to the service panel.
2. Thread the fan supply line through the outlet box so that the
fan supply line extends at least 6" beyond the box as shown in
Figure 8.
3. Attach the fan supply line to the outlet box with an approved
connector, available at any hardware store or electrical supply
house. Refer to Figure 8.
4. Make certain the wiring meets all national and local standards
and ANSI/NFPA 70.
c
e w
cc
e we w
A 70. IA 70. I
A 70. I
A 70. IA 70. I
uu
aa
lili
a
li
uu
aa
lili
h nh n
i
t
h n
ii
tt
h nh n
f yf y
oo
f y
o
f yf y
oo
ff
ii
ee
d ed e
ll
ee
f
i
e
d e
l
e
ff
ii
ee
d ed e
ll
ee
a-a-
a-
a-a-
c
uu
u
uu
cc
--
-
cc
--
FF
ii
gg
urur
e 6 - Ce 6 - C
uu
tt
tt
inin
g tg t
hh
e ce c
ee
ilinilin
g hg h
oo
ll
F
i
g
ur
e 6 - C
u
t
t
in
g t
h
e c
FF
ii
gg
urur
e 6 - Ce 6 - C
uu
tt
tt
inin
g tg t
e
hh
e ce c
ee
ilin
ilinilin
g h
g hg h
ee
o
l
e
oo
ll
ee
installing the support brace
If there is a ceiling joist directly above the hole which will allow the
outlet box to be recessed a minimum of 1/16" in the ceiling, go to
inin
ss
tt
aa
llinllin
g tg t
hh
e oe o
uu
tt
ll
ee
t bt b
oo
in
s
t
a
llin
g t
h
e o
inin
ss
tt
aa
llinllin
g tg t
u
hh
e oe o
uu
If there is not an adequate ceiling joist available, do the following:
41803-01 11/14/2002 © 2002 Hunter Fan Company
t
tt
l
e
ll
ee
t b
t bt b
xx
o
x section.
oo
xx
Page 5
55
5
55
Approved
Connector
Wire Leads
FF
ii
gg
urur
e 8 - Pre 8 - Pr
ee
pp
aa
rr
inin
g tg t
hh
e we w
irir
inin
F
i
g
ur
e 8 - Pr
e
p
a
r
in
FF
ii
gg
urur
e 8 - Pre 8 - Pr
g t
ee
pp
aa
rr
inin
g tg t
h
hh
e w
e we w
gg
ir
in
g
irir
inin
gg
You have now successfully prepared your ceiling fan site. For instructions on how to install your ceiling fan, continue with the
ss
tt
aa
llinllin
g tg t
hh
e ce c
ee
ilinilin
g pg p
ll
aa
tt
s
t
a
llin
g t
h
e c
e
ss
tt
aa
llinllin
g tg t
ilin
hh
e ce c
ee
ilinilin
g p
g pg p
ee
l
a
t
e section.
ll
aa
tt
ee
in-in-
in-
in-in-
installing the ceiling plate
1. Drill two pilot holes into the wood support structure through
the outermost holes on the outlet box. The pilot holes should
be 9/64" in diameter.
2. Thread the lead wires from the outlet box through the hole in
the middle of the ceiling plate.
3. Your fan comes with four neoprene noise isolators. Position
the isolators between the ceiling plate and ceiling by inserting
the raised areas on each isolator into the holes in the ceiling
plate. Refer to Figure 9.
Isolators
6. Tighten the screws into the 9/64" pilot holes; do not use lubricants on the screws. Do not overtighten.
Ceiling Joist
2 x 4 Brace
Ceiling Plate
Flat Washer
FF
ii
gg
urur
e 11 - Ie 11 - I
F
i
g
ur
e 11 - I
FF
ii
gg
urur
e 11 - Ie 11 - I
nn
ss
tt
aa
llinllin
g tg t
hh
llin
llinllin
g t
g tg t
e ce c
h
e c
hh
e ce c
n
s
t
a
nn
ss
tt
aa
Ceiling
Outlet Box
3” Wood Screw
ee
ilinilin
g pg p
ll
aa
ilin
ilinilin
g p
g pg p
tt
l
a
t
ll
aa
tt
e
ee
ee
e
ee
assembling the fan
assembling the fan for a standard or angled ceiling
1. Insert the downrod through the canopy and canopy trim ring
as shown in Figure 12. Feed wires from the fan through the
downrod.
2. Screw the downrod into the fan assembly until tight. IMPORTANT! Tighten downrod set screw as shown in Figure 12.
CC
AA
UU
TT
II
OO
N: TN: T
hh
e de d
oo
ww
nrnr
oo
d hd h
aa
s a ss a s
pp
ee
cc
ii
aa
l cl c
oo
aa
tt
inin
g og o
n tn t
C
A
U
T
I
O
CC
tt
hrhr
ee
t
hr
e
tt
hrhr
ee
tt
hh
e de d
t
h
e d
tt
hh
e de d
rr
ee
mm
r
e
m
rr
ee
mm
N: T
AA
UU
TT
II
OO
N: TN: T
aa
dd
ss
. D. D
o no n
a
d
s
. D
o n
aa
dd
ss
. D. D
o no n
oo
ww
nrnr
oo
d fd f
o
w
nr
o
d f
oo
ww
nrnr
oo
d fd f
oo
vv
e te t
hh
e de d
e t
e te t
oo
h
e d
o
hh
e de d
oo
o
v
oo
vv
3. Continue to the
oo
o
oo
w
t rt r
t r
t rt r
rr
r
rr
ww
ww
h
oo
o
oo
hh
h
hh
e d
hh
e de d
ee
mm
e
m
ee
mm
m unm un
m un
m unm un
nrnr
oo
nr
o
nrnr
oo
aa
nn
a
n
aa
nn
o
w
nr
o
d h
a
s a s
p
e
c
i
a
l c
o
a
t
oo
ww
nrnr
oo
d hd h
aa
s a ss a s
pp
ee
cc
ii
oo
vv
e te t
hh
ii
s cs c
oo
aa
tt
inin
g; tg; t
hh
o
v
e t
h
i
s c
o
hh
rr
ee
r
e
rr
ee
hh
h
hh
ww
w
ww
e fe f
e f
e fe f
ii
s cs c
inin
in
inin
oo
aa
a
aa
a
aa
gg
. O. O
g
. O
gg
. O. O
nn
n section.
nn
oo
vv
e te t
ss
cc
s
c
ss
cc
d.d.
d.
d.d.
gg
inin
g tg t
g
in
g t
gg
inin
g tg t
e ce c
t
in
g; t
h
e c
tt
inin
g; tg; t
hh
e ce c
nn
cc
e ae a
n
c
e a
nn
cc
e ae a
in
aa
l cl c
oo
aa
tt
inin
oo
aa
tt
inin
g pg p
o
a
t
in
g p
oo
aa
tt
inin
g pg p
ss
ss
ee
mbmb
ll
ee
s
s
e
mb
l
e
ss
ss
ee
mbmb
ll
ee
g o
g og o
r
d, dd, d
d, d
d, dd, d
hh
n t
h
n tn t
hh
rr
ee
vv
ee
nn
e
v
e
n
rr
ee
vv
ee
nn
o no n
oo
o n
o
o no n
oo
ee
e
ee
tt
ss
t
s
tt
ss
tt
t
tt
Ceiling Plate
FF
ii
gg
urur
e 9 - Ie 9 - I
nn
ss
ee
rr
tt
inin
g tg t
hh
e ie i
ss
oo
ll
aa
tt
oo
rr
s ins in
tt
o to t
hh
e ce c
ee
ilinilin
g pg p
ll
aa
tt
F
i
g
ur
e 9 - I
n
s
e
r
t
in
g t
h
e i
s
o
l
a
t
o
r
s in
t
o t
h
e c
e
FF
ii
gg
urur
e 9 - Ie 9 - I
nn
ss
ee
rr
tt
inin
g tg t
hh
e ie i
ss
oo
ll
aa
tt
oo
rr
s ins in
tt
o to t
ilin
hh
e ce c
ee
ilinilin
g p
g pg p
ee
l
a
t
e
ll
aa
tt
ee
4. Align the slotted holes (refer to Figure 10) in the ceiling plate
with the pilot holes in the wood support structure. Note: The
isolation pads should be flush against the ceiling.
For Angled Ceilings: Be sure to orient the ceiling plate so that
the arrows on the ceiling plate are pointing towards the ceiling
peak. Refer to Figure 10.
Slots
Arrows for Orienting
on Angled Ceiling
FF
ii
gg
urur
e 10 - Le 10 - L
oo
cc
aa
tt
inin
g tg t
hh
e se s
ll
oo
tt
tt
ee
d hd h
oo
ll
ee
s ts t
o uo u
ss
F
FF
i
g
ii
gg
ur
e 10 - L
urur
e 10 - Le 10 - L
o
c
a
t
in
g t
h
e s
l
o
t
t
e
d h
o
oo
cc
aa
tt
inin
g tg t
hh
e se s
ll
oo
l
tt
tt
ee
d hd h
oo
ll
ee
e
s t
o u
s
e
ee
s ts t
o uo u
ss
ee
5. Place a flat washer on each of the two 3" screws and pass the
screws through the slotted holes in the ceiling plate as shown
in Figure 11.
FF
F
FF
ii
gg
i
g
ii
gg
urur
e 12 - Ae 12 - A
ur
e 12 - A
urur
e 12 - Ae 12 - A
Hanger Ball/
Downrod Assembly
Canopy
Canopy Trim Ring
Set Screw
ss
ss
ee
mbmb
linlin
g tg t
hh
e de d
oo
ww
nrnr
oo
s
s
e
mb
lin
g t
h
linlin
g tg t
e d
hh
e de d
ss
ss
ee
mbmb
dd
o
w
nr
o
d
oo
ww
nrnr
oo
dd
© 2002 Hunter Fan Company 41803-01 11/14/2002
Page 6
66
6
66
assembling the fan for a low ceiling
1. Remove the screw on the hanger ball to disassemble it from
the downrod as shown in Figure 13.
Screw on the Hanger Ball
Hanger Ball/
Downrod
Assembly
FF
ii
gg
urur
e 13 - Re 13 - R
ee
mm
oo
vv
inin
g tg t
hh
e se s
cc
rr
ee
w fw f
rr
oo
m tm t
hh
e he h
aa
nn
gg
ee
r br b
aa
F
i
g
ur
e 13 - R
e
m
o
v
in
g t
h
e s
c
r
e
w f
r
o
m t
h
e h
FF
ii
gg
urur
e 13 - Re 13 - R
ee
mm
oo
vv
inin
g tg t
hh
e se s
cc
rr
ee
w fw f
rr
oo
m tm t
a
hh
e he h
aa
2. Remove the hook from the assembly.
3. Completely remove the set screw (identified in Figure 12) from
the fan adapter.
4. Put the set screw, previously removed, through the two black
neoprene washers and the hook as shown in Figure 14. Hook
must be installed in same orientation as shown in Figure 14.
Black Neoprene
Washer
Hook
Set Screw
llll
n
g
e
r b
a
ll
nn
gg
ee
r br b
aa
llll
8. Rotate the canopy until the arrow on the low profile washer
aligns with the tab hole on the canopy as shown in Figure 15.
9. Align the holes in the low profile washer with the holes in the
adapter and assemble securely with the three #8-32 x 1” screws.
installing the blade irons
1. Turn the fan upside down. Use the ceiling fan package to support the fan while assembling the blade irons.
2. Slide the blade iron under the switch housing plate aligning
the two notches with the two metal clips as shown in Figure
16. It may help to press down on the opposite side of the motor housing while installing.
3. Pull the blade iron forward over the metal clips to fully engage
the blade iron.
NOTE: If you have difficulty installing the blade iron, you can
loosen the screws and then tighten after installing.
Notch and Metal Clip
Blade Iron
FF
ii
gg
urur
e 14 - Ae 14 - A
ss
ss
ee
mbmb
linlin
g tg t
hh
e se s
ee
t st s
cc
rr
ee
w fw f
oo
r lr l
oo
w pw p
rr
oo
ff
ilil
F
FF
i
g
ii
gg
ur
e 14 - A
urur
e 14 - Ae 14 - A
s
s
e
mb
lin
g t
h
e s
e
t s
c
r
e
w f
o
r l
ss
ss
ee
mbmb
linlin
g tg t
hh
e se s
ee
t st s
cc
rr
aa
ss
ss
ee
mbmb
ll
yy
a
s
s
e
mb
l
y
aa
ss
ss
ee
mbmb
ll
yy
o
ee
w fw f
oo
r lr l
oo
w p
w pw p
ee
r
o
f
il
e
rr
oo
ff
ilil
ee
5. Reassemble the set screw to the adapter as shown in Figure 14.
NOTE: The rubber washers should be tight enough to keep
the hook standing straight up, but the set screw should not be
completely tighten as to keep the hook from being able to
swing.
6. Place the canopy trim ring then the canopy over the adapter
as shown in Figure 15.
7. Place the low profile washer (lip up) into the canopy as shown
in Figure 15 fitting the notch in the low profile washer over the
adapter set screw and hook.
Tab H ole
FF
ii
gg
urur
F
i
g
ur
FF
ii
gg
urur
e 15 - Ae 15 - A
e 15 - A
e 15 - Ae 15 - A
ss
ss
ee
mbmb
linlin
s
ss
g cg c
s
e
mb
lin
g c
ss
ee
mbmb
linlin
g cg c
Low Profile Washer
aa
nn
oo
pp
y fy f
a
n
o
p
y f
aa
nn
oo
pp
y fy f
oo
r lr l
oo
w pw p
o
r l
o
w p
oo
r lr l
oo
w pw p
Canopy
Canopy Trim Ring
Arrow on the
Low Profile
Wash er
rr
oo
ff
ilil
e me m
oo
r
o
f
il
e m
o
rr
oo
ff
ilil
e me m
oo
unun
un
unun
tt
inin
gg
t
in
g
tt
inin
gg
FF
ii
gg
urur
e 16 - Ae 16 - A
ss
ss
ee
mbmb
linlin
g tg t
hh
e be b
ll
aa
dd
e ire ir
oo
F
FF
i
g
ur
ii
gg
urur
e 16 - A
e 16 - Ae 16 - A
s
s
e
mb
lin
g t
h
linlin
g tg t
e b
hh
e be b
ss
ss
ee
mbmb
nn
l
a
d
e ir
o
n
ll
aa
dd
e ire ir
oo
nn
hanging the fan
1. Raise the fan and place the hook through the loop on the ceiling plate as shown in Figure 17. Use the note and arrow engraved in the ceiling plate to assist in determining the direction to assemble.
WW
AA
RR
NN
II
NN
G: FG: F
aa
n mn m
aa
y fy f
aa
ll ill i
f nf n
oo
t at a
ss
ss
ee
mbmb
ll
ee
d ad a
s dirs dir
ee
cc
tt
ee
W
A
R
N
I
N
G: F
a
n m
a
y f
a
ll i
f n
o
t a
s
s
e
mb
l
e
d a
WW
AA
RR
NN
II
NN
G: FG: F
aa
n mn m
aa
y fy f
aa
ll ill i
f nf n
oo
t at a
ss
ss
ee
mbmb
tt
hh
ee
ss
e ine in
ss
tt
aa
llll
aa
tt
ii
oo
n inn in
ss
tt
rr
uu
cc
tt
ii
oo
nn
ss
t
h
e
s
e in
s
t
a
ll
a
t
i
o
n in
s
t
r
tt
hh
ee
ss
e ine in
ss
tt
aa
llll
aa
tt
ii
oo
FF
F
FF
n inn in
Hook
ii
gg
urur
i
g
ur
ii
gg
urur
u
ss
tt
rr
uu
e 17 - Hae 17 - Ha
e 17 - Ha
e 17 - Hae 17 - Ha
..
c
t
i
o
n
s
.
cc
tt
ii
oo
nn
ss
..
Loop
nn
gg
inin
g tg t
hh
e fe f
aa
g t
g tg t
nn
h
e f
a
n
hh
e fe f
aa
nn
n
g
in
nn
gg
inin
s dir
ll
ee
d ad a
s dirs dir
d ind in
e
c
t
e
d in
ee
cc
tt
ee
d ind in
41803-01 11/14/2002 © 2002 Hunter Fan Company
Page 7
77
7
77
wiring the fan
1. Disconnect the power by turning off the circuit breakers to
the outlet box and associated wall switch location.
2. You can use either one or two wall switches to control the fan
and/or lights separately. Use connection 1, as described in Figure 18, to
• control the light with a wall switch and the fan with a pull
chain (one wall switch required),
• control the light with a pull chain and the fan with a wall
switch (one wall switch required), or
• control the light with one wall switch and the fan with
another (two wall switches required).
Use connection 2, as described in Figure 18, if there is no separate wall switch power wire for the light fixture.
NOTE: Wall switches not included.
3. Connect the wires as shown in Figure 18. To connect the wires,
twist the bare metal leads together. Place a wire nut over the
intertwined length of wire and twist clockwise until tight as.
CC
AA
UU
TT
II
OO
N: BN: B
e se s
urur
e ne n
o bo b
aa
rr
e we w
irir
e oe o
r wr w
irir
e se s
tt
rr
aa
nn
dd
s as a
rr
e ve v
nn
n
nn
s a
s as a
nn
n
nn
ii
r
e v
i
rr
e ve v
ii
d ld l
oo
cc
d l
o
c
d ld l
oo
cc
ff
aa
mm
iliili
aa
f
a
m
ili
a
ff
aa
mm
iliili
aa
..
.
..
C
CC
ibib
ll
e ae a
ib
l
e a
ibib
ll
e ae a
AA
ll wll w
A
ll w
AA
ll wll w
ee
ll
ee
cc
e
l
e
c
ee
ll
ee
cc
ww
ii
tt
h wh w
w
i
t
h w
ww
ii
tt
h wh w
2 x 4 Brace
A
U
T
I
O
N: B
AA
UU
TT
ff
tt
ee
r mr m
f
t
e
r m
ff
tt
ee
r mr m
irir
inin
ir
in
irir
inin
tt
rr
ii
cc
aa
t
r
i
c
a
tt
rr
ii
cc
aa
irir
ir
irir
Power
Wires
in
Ceiling
e s
II
OO
N: BN: B
e se s
aa
kk
inin
g cg c
a
k
in
g c
aa
kk
inin
g cg c
g mug mu
ss
t bt b
g mu
g mug mu
l cl c
l c
l cl c
inin
in
inin
e in ae in a
s
t b
e in a
ss
t bt b
e in ae in a
oo
dd
ee
s as a
nn
o
d
e
s a
n
oo
dd
ee
s as a
nn
gg
, y, y
oo
u su s
hh
g
, y
o
u s
h
gg
, y, y
oo
u su s
hh
Wall Switch Wire for Separate
Control of Light Fixture
Black
White
Bare or Green
ur
urur
oo
o
oo
d Ad A
d A
d Ad A
e n
o b
a
r
e w
ir
e o
r w
ir
e s
t
r
a
n
aa
a
aa
ll
l
ll
e se s
tt
t
tt
u au a
u a
u au a
ee
e
ee
d
tt
rr
aa
nn
dd
ii
oo
nn
aa
l al a
i
o
n
a
l a
ii
oo
nn
aa
l al a
rr
e une un
r
e un
rr
e une un
cc
tt
rr
ii
cc
ii
aa
c
t
r
i
c
i
a
cc
tt
rr
ii
cc
ii
aa
e ne n
o bo b
aa
rr
e we w
irir
e oe o
r wr w
irir
nnnn
ee
cc
tt
ii
oo
nn
ss
e
ee
cc
c
cc
NN
N
NN
d ud u
d ud u
c
cc
t
tt
cc
c
cc
SS
S
SS
i
o
ii
oo
oo
rr
o
r
oo
rr
I/NI/N
I/N
I/NI/N
ss
e a qe a q
s
e a q
ss
e a qe a q
n
s
nn
ss
dd
aa
d
a
dd
aa
FF
F
FF
..
.
..
nn
cc
e we w
n
c
e w
nn
cc
e we w
PP
A 70. IA 70. I
P
A 70. I
PP
A 70. IA 70. I
uu
aa
lili
u
a
li
uu
aa
lili
(Note: Wall
switch must be
acceptable as a
general-use
switch.)
ii
tt
h nh n
i
t
h n
ii
tt
h nh n
f yf y
f y
f yf y
ff
ii
ee
d ed e
f
i
e
d e
ff
ii
ee
d ed e
Outlet Box
oo
o
oo
nn
nnnn
oo
ulul
o
ul
d u
oo
ulul
installing the canopy
1. Rotate the fan 180º clockwise from the initial position when
hanging the fan. The arrows on the hanger ball and on the
ceiling plate should be pointing in the same direction and
should be pointing towards the tab hole on the canopy. Refer
to Figure 19.
FF
ii
gg
urur
e 19 - Re 19 - R
oo
tt
aa
tt
inin
g tg t
hh
e fe f
aa
F
i
g
ur
e 19 - R
o
t
a
t
FF
ii
gg
urur
e 19 - Re 19 - R
ss
--
s
-
ss
--
aa
ll
a
l
aa
ll
rr
r
rr
For Flush Mounting: The arrows on the low profile washer and
on the ceiling plate should be pointing in the same direction
and should be pointing towards the tab hole on the canopy.
2. Hook the tab hole over the tab on the ceiling plate as shown in
Figure 20.
in
oo
tt
aa
tt
inin
3. Raise the canopy, be sure the holes in the canopy and the ceiling plate are aligned, and loosely assemble the canopy screws
one at a time. When all three screws are assembled, securely
tighten all three canopy screws. Refer to Figure 20.
Tab Hole
and Tab
Canopy
Screw
g t
g tg t
nn
h
e f
a
n
hh
e fe f
aa
nn
Approved
Connectors
Green Ground Wire from
Hanger Pipe (not present
with flush mounting
option)
FF
ii
gg
F
i
g
FF
ii
gg
© 2002 Hunter Fan Company 41803-01 11/14/2002
urur
e 18 - We 18 - W
ur
e 18 - W
urur
e 18 - We 18 - W
White
2
Black
irir
inin
ir
in
irir
inin
1
Blk/Wht
3 Wires
from Fan
g tg t
hh
e fe f
g t
h
e f
g tg t
hh
e fe f
Ceiling Plate
Connections:
1. Connect Blk/Wht
wire from the fan to the
wall switch for separate
control of the light
fixture, or
2. Connect Blk/Wht
wire from the fan to the
ceiling black wire if there
is no separate wall
switch wire for the light
fixture.
aa
nn
a
n
aa
nn
FF
ii
gg
urur
e 20 - Ie 20 - I
nn
ss
tt
aa
llinllin
g tg t
hh
e ce c
aa
nn
oo
pp
F
i
g
ur
e 20 - I
n
s
t
a
llin
g t
FF
ii
gg
urur
e 20 - Ie 20 - I
nn
ss
h
tt
aa
llinllin
g tg t
hh
e c
e ce c
yy
a
n
o
p
y
aa
nn
oo
pp
yy
installing the canopy trim ring
1. To easily install the canopy trim ring, locate the two tabs on
the canopy trim ring. See Figure 21.
Canopy
Press Here when
Removing
Canopy
Trim Ring
FF
F
FF
ii
gg
i
g
ii
gg
urur
e 21 - Ce 21 - C
ur
e 21 - C
urur
e 21 - Ce 21 - C
aa
nn
oo
pp
y ty t
a
n
o
p
y t
aa
nn
oo
pp
y ty t
rr
im rim r
r
im r
rr
im rim r
Tab
Press Here when
Removing
inin
gg
in
g
inin
gg
Page 8
88
8
88
2. Take both hands and push the canopy trim ring up to the top
of the canopy. See Figure 21.
3. The canopy trim ring will snap and lock into place on the
canopy.
removing the canopy trim ring
1. Locate the tab indicators, small bumps on top of tabs. Refer to
Figure 22.
2. To remove the canopy trim ring, press firmly on opposite sides
of the ring towards the canopy as shown in Figure 22. The tabs
will flex out releasing the trim ring from the canopy.
FF
ii
gg
urur
F
i
g
ur
FF
ii
gg
urur
Tab Indica tor
e 22 - Re 22 - R
e 22 - R
e 22 - Re 22 - R
ee
mm
e
m
ee
mm
Canopy
oo
vv
inin
o
v
in
oo
vv
inin
Canopy Trim Ring
g tg t
hh
e ce c
aa
nn
oo
pp
e c
e ce c
y ty t
a
n
o
p
y t
aa
nn
oo
pp
y ty t
g t
g tg t
h
hh
rr
im rim r
r
im r
rr
im rim r
inin
gg
in
g
inin
gg
installing the blades
1. Open the locking mechanism as shown in Figure 23.
Locking Mechanism
Closed
FF
ii
gg
urur
e 24 - Ie 24 - I
nn
ss
tt
aa
llinllin
g tg t
hh
e be b
ll
aa
dd
F
i
g
ur
e 24 - I
n
s
t
a
llin
FF
ii
gg
urur
e 24 - Ie 24 - I
g t
nn
ss
tt
aa
llinllin
g tg t
ee
h
e b
l
a
d
e
hh
e be b
ll
aa
dd
ee
installing the light fixture
You can install with or without the light fixture. If you want to
inin
ss
tt
aa
llinllin
g wg w
ii
tt
hh
oo
uu
t tt t
install without the light fixture, skip to the
lili
gg
hh
t ft f
ii
xx
tt
urur
t f
t ft f
WW
W
WW
mm
m
mm
i
x
t
ii
xx
tt
AA
RR
A
R
AA
RR
oo
dd
o
d
oo
dd
ee
ur
e section.
urur
ee
NN
II
NN
N
I
N
NN
II
NN
ee
l.l.
e
l.
ee
l.l.
G: UsG: Us
G: Us
G: UsG: Us
e oe o
e o
e oe o
nlnl
nl
nlnl
y ty t
y t
y ty t
hh
e se s
upup
h
e s
up
hh
e se s
upup
li
g
h
lili
gg
hh
in
s
t
a
llin
g w
llinllin
ii
xx
i
x
ii
xx
i
g wg w
ii
tt
urur
e fe f
oo
t
ur
e f
o
tt
urur
e fe f
oo
inin
ss
tt
aa
pp
lili
ee
d lid li
gg
hh
e
ee
d li
d lid li
t ft f
g
h
t f
gg
hh
t ft f
p
li
pp
lili
attaching the upper switch housing
1. Partially install two #6-32 x 3/8" housing assembly screws into
the switch housing mounting plate as shown in Figure 25.
2. Feed the upper plug connector through the center opening of
the upper switch housing. See Figure 25.
hh
t
h
o
u
t t
h
tt
hh
oo
uu
t tt t
hh
r tr t
hh
ii
s fs f
aa
r t
h
i
s f
a
r tr t
hh
ii
s fs f
aa
ee
e
ee
nn
n
nn
Locking
Mechanism
FF
ii
gg
urur
e 23 - Oe 23 - O
pp
ee
nn
inin
g bg b
ll
aa
dd
e ire ir
oo
n ln l
oo
cc
kk
inin
g mg m
ee
cc
hh
aa
nn
ii
ss
F
FF
i
g
ur
ii
gg
urur
e 23 - O
e 23 - Oe 23 - O
p
e
n
in
g b
l
a
d
e ir
o
n l
o
c
k
in
pp
ee
nn
inin
g bg b
ll
aa
dd
e ire ir
oo
n ln l
g m
oo
cc
kk
inin
g mg m
mm
e
c
h
a
n
i
s
m
ee
cc
hh
aa
nn
ii
ss
mm
2. Align the holes in the blade with the blade iron as shown in
Figure 24.
3. Close the locking mechanism securely feeling it lock into place.
Switch Housing
Mounting Plate
FF
ii
gg
urur
e 25 - Ae 25 - A
F
i
g
ur
e 25 - A
FF
ii
gg
urur
e 25 - Ae 25 - A
Upper Switch
Housing
tt
tt
aa
cc
hh
inin
t
t
a
c
h
in
tt
tt
aa
cc
hh
inin
mm
m
mm
g tg t
g t
g tg t
hh
e upe up
pp
ee
r sr s
h
e up
p
e
r s
hh
e upe up
pp
ee
r sr s
oo
unun
tt
inin
g pg p
ll
o
un
oo
unun
aa
t
in
g p
l
a
tt
inin
g pg p
ll
aa
Housing
Assembly
Screw
Upper Plug
Connector
ww
ii
tt
cc
h hh h
oo
uu
sinsin
g tg t
o to t
hh
w
i
t
c
h h
o
u
ww
ii
tt
ee
t
e
tt
ee
sin
tt
cc
h hh h
oo
uu
sinsin
g t
g tg t
o t
o to t
ee
h
e
hh
ee
3. Align the keyhole slots in the upper switch housing with the
housing assembly screws installed previously.
4. Turn the upper switch housing counterclockwise until the
housing assembly screws are firmly situated in the narrow end
of the keyhole slots as shown in Figure 26. Install the one remaining #6-32 x 3/8" housing assembly screw into the third
hole in the upper switch housing. Tighten all three screws firmly.
41803-01 11/14/2002 © 2002 Hunter Fan Company
Page 9
FF
ii
gg
urur
cc
c
cc
urur
ur
urur
ss
s
ss
ff
f
ff
ee
e
ee
ii
i
ii
urur
ur
urur
xx
x
xx
CC
C
CC
ee
e
ee
e te t
e t
e te t
mbmb
mb
mbmb
tt
urur
t
ur
tt
urur
AA
A
AA
F
FF
ll
y ay a
l
y a
ll
y ay a
o po p
o p
o po p
UU
U
UU
ll
l
y s
ll
e fe f
e f
e fe f
i
ii
y sy s
y sy s
g
ur
gg
urur
TT
II
OO
T
I
O
TT
II
OO
tt
tt
t
t
tt
tt
rr
r
rr
cc
c
cc
aa
llinllin
a
llin
aa
llinllin
e 26 - Me 26 - M
e 26 - M
e 26 - Me 26 - M
aa
a
aa
oo
o
oo
rr
r
rr
N: MN: M
N: M
N: MN: M
cc
hh
ee
c
h
e
cc
hh
ee
pp
ee
rr
p
e
r
pp
ee
rr
ee
ww
s cs c
e
w
s c
ee
ww
s cs c
gg
..
g
.
gg
..
d td t
d t
d td t
ll
y ay a
l
y a
ll
y ay a
oo
unun
tt
inin
g tg t
hh
e upe up
pp
ee
r sr s
ww
ii
tt
cc
h hh h
oo
uu
sinsin
tt
t
tt
cc
c
cc
unun
un
unun
hrhr
hr
hrhr
o
oo
h hh h
h h
h hh h
e
oo
uu
o
u
oo
uu
u
uu
tt
t
tt
ee
ee
sin
sinsin
oo
o
oo
inin
in
inin
e he h
e h
e he h
sinsin
sin
sinsin
g
uu
u
uu
g pg p
g p
g pg p
gg
gg
sinsin
sin
sinsin
oo
o
oo
g ag a
g a
g ag a
g ig i
s ss s
g i
s s
g ig i
s ss s
ll
aa
tt
ee
. F. F
aa
il-il-
l
a
t
e
. F
a
il-
ll
aa
tt
ee
. F. F
aa
il-il-
uu
sinsin
g ag a
u
sin
g a
uu
sinsin
g ag a
nn
d lid li
gg
hh
n
d li
g
h
nn
d lid li
gg
hh
o
un
t
in
g t
h
e up
p
e
r s
w
i
t
c
oo
unun
tt
inin
g tg t
hh
e upe up
pp
aa
kk
e se s
urur
e te t
hh
cc
c
cc
ur
urur
ww
w
ww
h ah a
h a
h ah a
ee
ss
e
s
ee
ss
e t
e te t
ii
i
ii
ulul
ul
ulul
h
hh
tt
cc
t
c
h h
tt
cc
nn
d td t
n
d t
nn
d td t
t in tt in t
t in t
t in tt in t
e upe up
e up
e upe up
h hh h
h hh h
oo
uu
o
u
oo
uu
ii
gg
hh
i
g
h
ii
gg
hh
hh
h
hh
a
k
e s
aa
kk
e se s
o to t
hh
e se s
o t
h
e s
o to t
hh
e se s
tt
tt
aa
t
t
a
tt
tt
aa
oo
ulul
d rd r
o
ul
d r
oo
ulul
d rd r
ee
e se s
e s
e se s
r sr s
pp
p
pp
sinsin
sin
sinsin
tt
t
tt
ee
e
ee
ee
e
ee
ww
w
ww
ww
r sr s
r s
r sr s
g mg m
g m
g mg m
n an a
n a
n an a
h h
ii
tt
cc
h hh h
ww
ii
w
i
ww
ii
oo
o
oo
ll tll t
ll t
ll tll t
ii
tt
cc
h hh h
i
t
c
h h
ii
tt
cc
h hh h
attaching the lower switch housing
1. Connect the upper plug connector from the motor to the lower
plug connector in the lower switch housing assembly. See Figure 27.
NOTE: Both plug connectors are polarized and will only fit together one way. Make sure that both connectors are properly
aligned before connecting them together. Incorrect connection could cause improper operation and damage to the product.
e-e-
e-
e-e-
s
99
9
99
6. Thread the fan pull chain and light pull chain through the appropriate holes.
7. Thread the light pull chain through the finial and screw the
finial onto the threaded rod end until tight.
Lower Switch
Metal Disk
Finial
hh
e ge g
h
e g
hh
e ge g
ll
l
ll
Housing
Threaded Rod
Light Pull Chain
Cover Plate
aa
ss
s bs b
oo
ww
ll
a
s
s b
o
w
l
aa
ss
s bs b
oo
ww
ll
Fan Pull Chain
ss
--
-
ss
-tt
t
tt
Glass Bowl
FF
ii
gg
urur
e 28 - Ie 28 - I
F
i
g
ur
e 28 - I
FF
ii
gg
urur
e 28 - Ie 28 - I
nn
ss
tt
aa
llinllin
g tg t
n
s
t
a
llin
g t
nn
ss
tt
aa
llinllin
g tg t
Upper Switch
Housing
Housing
Assembly
Screw
FF
ii
gg
urur
F
i
g
ur
FF
ii
gg
urur
Lower Plug
Connector
e 27 - Ce 27 - C
e 27 - C
e 27 - Ce 27 - C
oo
nnnn
ee
cc
tt
inin
nn
nnnn
g tg t
e
c
t
in
g t
ee
cc
tt
inin
g tg t
o
oo
hh
h
hh
e pe p
e p
e pe p
Upper Plug
Connector
lulu
g cg c
oo
lu
g c
o
lulu
g cg c
oo
nnnn
nn
nnnn
Lower
Switch
Housing
ee
cc
tt
oo
e
c
t
o
ee
cc
tt
oo
rr
ss
r
s
rr
ss
2. Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower
switch housings. Attach the lower switch housing to the upper switch housing with three #6-32 x 3/8" housing assembly
screws. See Figure 27.
installing the glass bowl
Refer to Figure 28.
1. Install two max 60 Watt medium base incandescent bulbs.
2. Attach the extra pull chain (included in the sack parts) to the
fan pull chain using the plastic breakaway connector.
3. Thread the fan pull chain through the hole in the metal disk.
Then, thread the fan pull chain through the small hole beside
the hole in the center of the glass bowl.
4. Thread the light pull chain through the hole in the center of
the glass bowl.
5. Place the cover plate up against the glass bowl. Align the holes
in the cover plate and glass bowl.
installing without the light fixture
Your Hunter fan comes with an integrated light fixture assembly
and an optional switch housing cap and finial. This feature gives
you the option of installing the fan with or without the included
light fixture.
If you decide to install the fan without the integrated light fixture
please complete the following instructions to install the optional
switch housing cap and finial.
attaching the upper switch housing
1. Partially install two #6-32 x 3/8" housing assembly screws into
the switch housing mounting plate as shown in Figure 25.
2. Feed the upper plug connector through the center opening of
the upper switch housing. See Figure 25.
3. Align the keyhole slots in the upper switch housing with the
housing assembly screws installed previously.
4. Turn the upper switch housing counterclockwise until the
housing assembly screws are firmly situated in the narrow end
of the keyhole slots as shown in Figure 26. Install the one remaining #6-32 x 3/8" housing assembly screw into the third
hole in the upper switch housing. Tighten all three screws firmly.
CC
AA
UU
TT
II
OO
N: MN: M
aa
kk
e se s
urur
e te t
hh
e upe up
pp
ee
r sr s
ww
ii
tt
cc
h hh h
oo
uu
sinsin
g ig i
u
uu
g pg p
g p
g pg p
sin
sinsin
oo
o
oo
g ag a
g a
g ag a
s ss s
g i
s s
g ig i
s ss s
ll
aa
tt
ee
. F. F
aa
il-il-
l
a
t
e
. F
a
il-
ll
aa
tt
ee
. F. F
aa
il-il-
uu
sinsin
g ag a
u
sin
g a
uu
sinsin
g ag a
nn
d lid li
gg
hh
n
d li
g
h
nn
d lid li
gg
hh
cc
c
cc
urur
ur
urur
ss
s
ss
ff
f
ff
i
ur
ee
e
ee
ii
ii
urur
urur
xx
x
xx
C
CC
ee
e
ee
e te t
e t
e te t
mbmb
mb
mbmb
tt
urur
t
ur
tt
urur
A
AA
ll
y ay a
l
y a
ll
y ay a
o po p
o p
o po p
U
UU
ll
l
ll
e fe f
e f
e fe f
y sy s
y s
y sy s
T
TT
I
II
tt
tt
t
t
tt
tt
aa
a
aa
O
OO
rr
r
rr
cc
c
cc
llinllin
llin
llinllin
aa
a
aa
oo
o
oo
rr
r
rr
N: M
N: MN: M
cc
hh
ee
d td t
c
h
e
d t
cc
hh
ee
d td t
pp
ee
rr
p
e
r
pp
ee
rr
ee
ww
s cs c
e
w
s c
ee
ww
s cs c
gg
..
g
.
gg
..
ll
y ay a
l
y a
ll
y ay a
a
k
e s
ur
e t
h
e up
p
e
r s
w
i
t
c
h h
ll tll t
ll t
ll tll t
h hh h
h h
h hh h
o
ii
tt
cc
h hh h
oo
oo
unun
tt
inin
o
un
t
in
oo
unun
tt
inin
hrhr
ee
e he h
hr
e
e h
hrhr
ee
e he h
oo
uu
sinsin
o
u
sin
oo
uu
sinsin
aa
kk
e se s
urur
e te t
hh
e upe up
pp
ee
r sr s
ww
o to t
hh
e se s
ww
ii
tt
cc
h hh h
oo
uu
sinsin
o t
h
e s
w
i
t
c
e se s
cc
c
cc
ww
h ah a
h a
h ah a
ee
ss
e
s
ee
ss
ulul
ul
ulul
ii
tt
cc
nn
d td t
n
d t
nn
d td t
t in tt in t
t in t
t in tt in t
h h
h hh h
o to t
hh
tt
tt
aa
t
t
a
tt
tt
aa
oo
ulul
d rd r
o
ul
d r
oo
ulul
d rd r
g mg m
o
u
sin
g m
oo
uu
sinsin
g mg m
ii
gg
hh
tt
ee
n an a
i
g
h
t
e
n a
ii
gg
hh
tt
ee
n an a
hh
e se s
ww
ii
tt
cc
h
e s
w
i
t
c
hh
e se s
ww
ii
tt
cc
e-e-
e-
e-e-
s
ss
--
-
ss
-tt
t
tt
© 2002 Hunter Fan Company 41803-01 11/14/2002
Page 10
1010
10
1010
attaching the lower switch housing
uninstalling the light fixture
Refer to Figure 29.
1. Disconnect the plug connectors between the black wire and
the black/white wire.
2. Disconnect the plug connectors between the two white wires.
3. Uninstall the nut and washer from the end of the light fixture
inside of the lower switch housing.
4. Unscrew the threaded rod of the light fixture from the lower
switch housing.
5. Remove the light fixture from the lower switch housing pulling disconnected wires through the hole in the center of the
lower switch housing.
NOTE: When removing the wires, pull the thin plug connector (male) through first, and then pull the other plug connector (female) through the hole.
6. Install the dummy terminals (included in the sack parts) on
the two disconnected wires in the lower switch housing.
Lower Switch
Housing
installing the lower switch housing
1. Connect the upper plug connector from the motor to the lower
plug connector in the lower switch housing assembly. See Figure 27.
NOTE: Both plug connectors are polarized and will only fit together one way. Make sure that both connectors are properly
aligned before connecting them together. Incorrect connection could cause improper operation and damage to the product.
2. Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower
switch housings. Attach the lower switch housing to the upper switch housing with three #6-32 x 3/8" housing assembly
screws. See Figure 27.
Threaded Rod
FF
ii
gg
urur
e 29 - Re 29 - R
ee
mm
oo
vv
inin
g tg t
hh
e lie li
gg
hh
t ft f
ii
xx
tt
urur
F
FF
i
g
ii
gg
ur
e 29 - R
urur
e 29 - Re 29 - R
e
m
o
v
in
g t
h
e li
g tg t
g
hh
e lie li
gg
ee
mm
oo
vv
inin
ee
h
t f
i
x
t
ur
e
hh
t ft f
ii
xx
tt
urur
ee
installing the switch housing cap and plug button
Install the switch housing cap and plug button to the lower switch
housing as shown in Figure 30.
Lower Switch
Housing
Cap
Plug Button
FF
ii
gg
urur
e 30 - Ie 30 - I
nn
ss
tt
aa
llinllin
g tg t
hh
e se s
ww
ii
tt
cc
h hh h
oo
uu
sinsin
g cg c
aa
p ap a
nn
d pd p
lulu
F
i
g
ur
e 30 - I
n
s
t
a
llin
g t
h
e s
w
i
t
c
h h
o
u
sin
g c
a
FF
ii
gg
urur
e 30 - Ie 30 - I
nn
ss
tt
aa
llinllin
g tg t
hh
e se s
ww
ii
tt
cc
h hh h
oo
bb
uu
tt
tt
oo
nn
b
u
t
t
o
n
bb
uu
tt
tt
oo
nn
p a
uu
sinsin
g cg c
aa
p ap a
gg
n
d p
lu
g
nn
d pd p
lulu
gg
41803-01 11/14/2002 © 2002 Hunter Fan Company
Page 11
1111
11
1111
operating your ceiling fan
1. Turn on electrical power to the fan.
2. The fan pull chain controls power to the fan. The pull chain
has four settings in sequence: High, Medium, Low and Off.
• Pull the chain slowly to change settings.
• Release slowly to prevent the chain from recoiling into the
blades.
• The chain uses a breakaway connector that separates if
the chain is jerked. If this happens, simply reinsert the chain
into the connector.
3. The light pull chain controls power to the light. The pull chain
has two settings: On and Off.
4. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in warm weather to cool the room with a
direct breeze. In winter, having the fan draw air upward (clockwise blade rotation) will distribute the warmer air trapped at
the ceiling around the room without causing a draft. Refer to
Figure 31.
FF
ii
gg
urur
e 31 - Ae 31 - A
ir fir f
ll
oo
w pw p
aa
tt
tt
ee
rr
nn
ee
e
ee
a
t
aa
tt
vv
ee
v
e
vv
ee
ss
t
e
r
n
s
tt
ee
rr
nn
ss
Reversing
Switch
rr
sinsin
g sg s
r
sin
g s
rr
sinsin
g sg s
ww
ii
tt
cc
hh
w
i
t
c
h
ww
ii
tt
cc
hh
F
i
g
ur
e 31 - A
ir f
l
o
FF
ii
gg
urur
e 31 - Ae 31 - A
ir fir f
w p
ll
oo
w pw p
To change the direction of air flow, turn the fan off and let it
come to a complete stop. Slide the reversing switch on the fan
to the opposite position as shown in Figure 32. Restart fan.
Fan Pull
Chain
FF
ii
gg
urur
e 32 - Pe 32 - P
ull cull c
hh
aa
in ain a
nn
F
FF
i
g
ii
gg
ur
e 32 - P
urur
e 32 - Pe 32 - P
ull c
ull cull c
d rd r
h
a
in a
n
d r
hh
aa
in ain a
nn
d rd r
cleaning your ceiling fan
caring for finishes
For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt
and dust can easily be removed by using a mild detergent and a
slightly dampened cloth. An artistic agent may be used, but never
use abrasive cleaning agents as they will damage the finish.
caring for blades
Wood finish blades should be cleaned with a furniture polishing
cloth. Occasionally, a light coat of furniture polish may be applied
for added protection and beauty. Painted and high-gloss blades
may be cleaned in the same manner as the fan finish.
troubleshooting
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the
ww
irir
inin
g tg t
hh
e fe f
aa
w
ir
in
g t
ww
irir
inin
g tg t
3. Check the plug connection in the switch housing.
4. Push motor reversing switch firmly up or down to ensure
that the switch is engaged.
5. Pull the pull chain to ensure it is on.
6. Remove the shipping bumpers.
Problem: Noisy operation.
1. Check to see if the blade bracket is secure.
2. Check to see if the blade is secure.
3. Check to see if the blade is cracked. If so, replace all the
blades.
4. Change to an approved speed control.
5. Be sure that the glass is secure.
6. Check and tighten the screws in the switch housing
mounting plate and in the upper and lower switch housing.
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan.
2. Turn power off, support fan very carefully, and check that
the hanger ball is properly seated.
If you need parts or service assistance, please call 888-830-1326 or
visit us at our WEB site at http://www.hunterfan.com.
h
e f
hh
e fe f
nn
a
n section.
aa
nn
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
© 2002 Hunter Fan Company 41803-01 11/14/2002
Loading...