HumidiCup S1, M1 User Manual

HumidiCup ®

Electronic Cigar Humidifier S1 & M1 User Manual

 Electronic humidification system for Humidors or

cigar cabinets

 Precise humidity measurement and control

 Audio & display alarms for fan error or lack of

water

 Low power consumption（1 Watts max.）

 Easy-to-Use

Control Unit

Water Cartridge

Ribbon cable

AC/DC Adaptor

CAUTION

 To prevent accidents arising from the misuse of this

humidifier, read this manual thoroughly and be sure
you understand it before attempting to use the
humidifier and use the humidifier according to the
information provided.

 Avoid water to get into the control unit. The product

may operate in an unexpected manner, resulting in
damage to the product or resulting in accidents with
water get into the control unit.

 Dry the control unit if there is any water get into the

control unit.

1. Installations

Step #1, The Cigar Humidifier S1 or M1 you received is assembled

product. You need remove all plastic packaging. Hold the gray water
cartridge by one hand and sliding pull back white control unit
slightly toward LED by another hand and take it off from the water
cartridge
Step #2, Fill water cartridge with distilled water slowly until floral
foam inside cartridge is fully saturated. Pour out any excess water
from cartridge and wipe dry the outsides of the cartridge.
Step #3, Locate control unit to water cartridge. Hold water cartridge
by a hand and sliding push control unit slightly toward logo on
control unit to lock it with water cartridge. There is an align mark on
control unit and water cartridge. Make sure the marks are aligned.
Step #4, Power cord connection. The humidifier works with 5VDC
voltage supply. An AC/DC adaptor and an USB cable has been
provided to convert 100~240VAC into 5VDC for the humidifier.
Connect USB port of USB cable to the AC/DC adaptor and connect
the DC connector of USB cable to “5VDC in” power port on
control unit directly or through the ribbon cable that is for limited
spacing for cable passing through.

Step #5, Plug the adaptor to power supply socket to run the
humidifier.
 You may use a 5V battery as the power supply of the humidifier.

The battery should not be with the function that shut down
without current.

 External fan is available as optional part that is for cigar cabinet

with large size to improve air circulation in the storage
environment. There is an “External fan/5VDC out” port on the
side of control unit. This port can be connected to an external fan
as the power supply of external fan and also can be used as
electronically parallel connection with another S1 or M1
humidifier.

2. Setting

There are three rubber keys for setting on top of the control unit.
The humidifier is factory set at 70%RH and can be adjusted by user
to any value from 60%RH to 80%RH. Key “▲” is to increase the
humidity setting value. Key “▼” is to decrease humidity setting
value. The LED displayed humidity value is the humidity value
measured by the sensor inside adding with calibration value. The
fan will run to blow the moist airflow to humidor or cigar cabinet
when the LED displayed humidity value is lower than humidity
setting value. The fan will stop when the LED displayed humidity
value is equal or higher than humidity setting value. Key “C” is for
Calibration. You may adjust calibration value if you are sure the
LED displayed humidity value is not accurate as another humidity
meter on your hand. The factory default calibration value is zero
You may click key “C”, and you will see the calibration value
displayed from LED, within approx. 3 seconds, to press Key “▲”
or “▼” to increase or decrease the calibration value by 0.1 step in a
range of -5.0 to +5.0. For example, if you are sure the displayed
humidity value from the humidifier is 2%RH higher than the
humidity value measured by a high accurate humidity meter, you
may set calibration data as -2.0 , and then the displayed humidity

value on the humidifier will be measured humidity value plus with
the calibration data -2.0. The setting value will not be lost even the
humidifier be power off or re-power on.

3. Alarms

There are two alarms for internal fan error and lack of water. LED
will display “ ” and buzzer will alarm to indicate “Fan error”
issue in case of internal fan is failed. LED will display “ ” and
buzzer will alarm to indicate “Lack of water” issue in case of the
measured humidity value is 10%RH at least lower than humidity
setting value for one hour at least that mostly is caused by lack of
water. Alarm “Lack of water” could be happened in case of the size
of your humidor or cigar cabinet exceeds the capability of the
humidifier or the humidor/cigar cabinet is not sealed well.

4. Location

You may put the humidifier in your humidor or cigar cabinet after
the humidifier has been installed and set. Make sure the air paths of
the humidifier have not been blocked. Keep at least 1 inches (2.5cm)
clearance from the vent of humidifier to cigars or lid. Cigars should
not be stacked upon the humidifier.

5. Warranty

Smart-lion Tech. Ltd. Co. warrants goods of its manufacture as
being free of defective materials and faulty workmanship. If the
warranted goods are returned to Smart-lion during the
warranty period of one year after date purchase, we will repair
or replace the electronic parts without charge those items it
finds defective. The warranty only applies to original purchaser
at retailed and may not be transferred.

00001-EN REVA May. 2015
Copyright ©2015 Smart-Lion Tech. Co., Ltd.

www.humidicup.com