HM-1100A_MAN_0712
product manual
HM-1100A
Dead-Weight
Consolidation
Load Frame
Setup and Operating Instructions
INSPECT THE CONTENTS OF THE CARTON (S) TO MAKE SURE
ALL O OF THE COMPONENTS HAVE BEEN RECEIVED. THE
SHOULD INCLUDE:
Load Frame with lever loading arm
Adjustable counter balance weight with threaded rod and two (2) nuts
Dial indicator support rod— 3/4” dia. x 12” long
Dial Indicator adjusting bracket
Weight hanger with connecting pin
Load holding screw with adjusting knob
(2) 3/8-16 x 6” anchor bolts with (4) nuts and (4) washers
Optional Accessories
Slotted weights (as ordered)
H-4471CC optional Dial Indicator 0.5” x .0001” counterclockwise
HM-1100.1 Optional Stand
HM-1220.25.4 Optional Calibration Disk for 2.5” dia.
HM-1220.25 Optional Fixed-Ring Consolidation Cell 2.5” dia.
NOTE: THE TABLE TOP THAT THE LOAD FRAME IS RESTING ON
SHOULD BE OF HEAVY-DUTY CONSTRUCTION TO SUPPORT THE
WEIGHTS REQUIRED FOR THE TEST.
1. Place the load frame on a lab bench or other suitable mounting
location and inset the load holding screw into the block at the
channel end from the bottom, so that the ball end of the screw will
make contact with the bottom of the lever arm when changing to the
next higher load. Attach the weight hanger with the pin provided.
There are three (3) ratio positions for this hanger (9:1, 10:1 and 11:1).
The chart that follows on the next page is set up for the 10:1 ratio
with a 2.5” diameter sample. Be sure you have sufficient clearance
for the weight hanger with weights before securing the base to the
tabletop using the (2) anchor bolts supplied.
2. Attach the dial indicator support rod to the right of the base. Next,
attach the dial indicator holder to the support rod. Finally, attach the
dial indicator to the holder.
3. Screw the counter weight threaded rod into the rear of the lever arm,
about 1” and tighten the jam nut. Adjust the counter-weight until the
lever balances at a level position with the top loading arm vertical
and tighten the nut. You might want to consider adjusting the weight
until there is a seating load on the sample (ASTM D2435 for details)
4. Place the consolidometer with smaple on the load platform and ad-
just the top cross arm adjusting screw until it makes contact with the
load pad in the consolidometer. Position the dial indicator over the
cross arm screw until it makes contact with the load pad in the consolidometer. Position the dial indicator over the cross arm screw and
adjust the indicaotrl to the desired setting. the seating load can now
be applied by backing off on the load holding screw, making sure
there is sufficient clearance between the screw and the lever arm.
5. Refer to ASTM D2435, D4546, AASHTO T216 OR BS 1377:PART
5:1990 for additional information on specific test procedures.
6. ASTM D-2435 requires that corrections for vertical deformations in
the frame must be made by sing a steel calibration disc the same
height as the sample and 0.04” smaller in diameter.
Dead Weight Consolidation Load Chart
2.5” Dia. Sample, Area = 4.9087 in
2
Weights Added 10:1 Beam = Sample Load
Quantity Lb Wt. Total lbs TSF
1 .852 8.52 1/8
1 .852 17.04 1/4
1 1.704 34.09 1/2
1 3.409 68.18 1
1 6.818 136.35 2
1 13.635 272.7 4
1 27.27 545.4 8
2 27.27 1090.8 16
4 27.27 2181.6 32
Weights Sets
Kg Weight Set 1Kg 4 Kg 8Kg
HM-1122 4 3 2
HM-1123 4 5 5
16 tsf Weight Set 1/8 tsf 1/4 tsf 1/2 tsf 1/8 tsf 2 tsf 4 tsf
HM-1120 2 1 21 1 1 1
32 tsf Weight Set
HM-1121 Add (4) 4 tsf weights to the 16 tsf set listed above
Consolidation (Dead Weight)
Part # Qty Description
Dead Weight Consolidation
HM-1100A
HM-1120*
HM-1220.XX
H-4471CC
Dead Weight Consolidation w/ Analog Data Acquisition
HM-1100A
HM-1120*
HM-1220.XX
HM-2310.04
HM-2310BR
HM-2325A.3F
HM-1100SW
Dead Weight Consolidation w/ Digital Data Acquisition
HM-1100A
HM-1120*
HM-1220.XX
HM-4469.10
HM-4469C
HM-2330D.3F
HM-1100SW
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Typical Setups:
Dead Weight Consol Frame-Front Load
Weight Set, 16 TSF
Fixed Ring Consolidation Cell
Dial Gauge, 0.5" X .0001" CC
Dead Weight Consol Frame-Front Load
Weight Set, 16 TSF
Fixed Ring Consolidation Cell
Strain Transducer 0.4" (10mm)
Strain Transducer Bracket
MiniLogger 4 CH Analog Data Acquisition
HMTS Consolidation Reporting Software
Dead Weight Consol Frame-Front Load
Weight Set, 16 TSF
Fixed Ring Consolidation Cell
Digital Indicator 1" x .0001"
(25 x 0.002 mm)
Data Cable for Indicator
MiniLogger 4 CH Digital Data Acquisition
HMTS Consolidation Reporting Software
Consolidation testing to
ASTM D2435, D4546;
AASHTO T216 and BS
1377 part 5 can be
carried out using our
manual loading frame,
the HM-1100A or one of
the pneumatic loading
machines, the HM-2432
or HM-2470A.
Specifications
Load Capacity 48 tsf (4,597 kPa)
Beam Ratios 9:1, 10:1 and 11:1
Heavy-duty aluminum
Frame Construction
Cell Platform
Dimension
(W x D x H)
Weight 47 lbs. (21kg)
Shipping Weight 62 lbs (28kg)
frame with stainless steel
vertical, horizontal and
beam support rods
Anodized aluminum with
locating pins for centering
cells.
7-3/4" x 32" x 19-1/2"
(197 x 812 x 495 mm)
Part Numbers ending in .XX
require a size code to be
entered referring to the sample size
to be tested.
For Consolidation samples, sizes
are: .20 = 2.0"; .242 = 2.42";
.25 = 2.5"; .30 = 3.0"; .40 = 4.0";
.50 = 50mm; .70 = 70mm;
.75 = 75mm, and .100 = 100mm.
*For Metric applications, use HM-
1122, Weight Set, 32kg.
Single-Station Frame Stand— HM-1100.1
Triple-Station Frame Stand— HM-1100.3
Butcher Block Table-top with heavy-duty, steel
frame designed to provide stable mounting
platform for HM-1100A Consolidation frames.
Consolidation frames can be bolted to table
too and table can be bolted to floor for
increased stability.
Single: Shipping wt. 50 lbs. (23kg)
Triple: Shipping wt. 75 lbs. (34kg)
Humboldt Mfg. Co.
875 Tollgate Road
Elgin, Illinois 60123 U.S.A.
U.S.A. Toll Free: 1.800.544.7220
Voice: 1.708.456.6300
Fax: 1.708.456.0137
Email: hmc@humboldtmfg.com
Loading...