Humboldt H-4215 User Manual

05.09
product manual
H-4215
Rapid Soil Processor
Introduction
Compact all-metal soil processor allows customer to produce five-point moisture density relationship test results in about 5 hours. Processor also handles samples for rapid compaction of a family of curves test. Processes
Operation The Rapid Soil Processor was designed and constructed to process Field Sample Moist Soil Only. After the material has been processed, it can be rerun
regardless of moisture content; this is beneficial to reduce drying time or pro­duce smaller particles to absorb moisture. This machine can be used to blend various types of soil regardless of moisture content but attempting to process dry chunks could damage the screen and the machine.
DO NOT ATTEMPT TO TEST LARGER THAN 3/4 INCH AGGREGATE.
The Rapid Soil Processor is designed to process moist soils containing aggre­gates up to 3/4 inch diameter maximum. The machine is constructed to accom­modate 14-gauge screens. This is determined by the type of material and the amount of gravel in the material to be processed.
Safety
1. CAUTION: The machine has 2,325 ft. lbs. of torque on the drum shaft.
2. The Guard over the drum gear and chain should be in a closed position
when the machine is in operation. It is easily raised for cleaning and loading the machine.
3. The machine is equipped with three switches. Switch #1 on the arm of the
pressure plate automatically shuts the switch off before pressure damages the screen or drum. Switch #2 is manually operated to control the machine at any time and position. Switch 3 on the safety guard must be closed for the processor to operate.
4. DRY MATERIAL OR MATERIAL CONTAINING AGGREGATE OVER 3/4
INCH SHOULD NOT BE PROCESSED.
5. The Spring Tension on the Pressure Plate, which releases gravel without
damaging the screen is Pre-Set and should not be changed.
6. The Weight on the Pressure Plate Arm has been pre-determined and should
be sufficient to move material into the screen.
Operating Instructions
1. Be sure that the Automatic Kill Switch (H-4215.50) is properly set
before starting the machine.
2. Detach weight from the Pressure Plate Arm (H-4215.3.4).
3. Release Catch (H-4215.3.12) on the Pressure Plate Guide and open the
material container space.
4. Be sure the Guard, (H-4215.9), is in place.
5. Both Switches (H-4215.50.1), must be correctly set to start the test.
The yellow guard switch has to be closed and the pressure plate switch has to be open.
6. Fill the machine with material to be processed. When full, attach the weight to the pressure plate arm.
7. On some impervious materials, the cut face of the material will appear glazed slowing the cutting process. Stop the machine and break up the material. Resume operation.
8. If gravel accumulates on the face of the material, stop the machine, open the pressure plate, and remove the rock.
Maintenance
1. The Pillow Block Bearings on the drum should be greased once every six months. Be careful not to blow the grease seals on the bearings.
2. Do not oil the chain drive. Check periodically for slack in the chain-keep the chain tight.
3. Check oil level in the gear box every six months.
4. All Bearings are stock items in most localities and can be replaced with a minimum of down time.
5. To change the screen see the ”Screen Replacement Procedure“.
6. Pre-shaped Screens (H-4215.32) may be ordered from Humboldt.
Unit Cleaning
1. Release Pressure Plate (H-4215.3 and H-4215.3.12), and bring to open position; by lifting out the Pressure Plate (H-4215.3.4), the machine will open, exposing the inside of the Pressure Plate, Plate Guide, Screen
and Table Top.
2. The Cleaning Attachment on the back side, will help clean the Screen by letting the machine run a short time while it is empty.
3. Tools used in cleaning the machine are a Wire Brush, Rubber Mallet, Bristle Brush, Spatula and Knife.
4. If the machine is not used constantly, let the material dry on the screen. Then start the machine and tap the screen with the rubber mallet.
5. Wipe all parts which come in contact with the processed material, with a damp cloth containing light oil. This will prevent the material from sticking but will not affect the test results.
Accessory Parts for Screen Replacement
(6) 114-20 Flat head screen-retaining screws and nuts. (4) 1I4" Hex-head screen-retaining strip screws. (1) Screen: H-4215.32
Screen Replacement Procedure
Note: The drum should be aligned with screen towards the front of the
machine. Should it become necessary to rotate the drum during the following procedure, be sure the machine is turned Off and Unplugged prior to continuing
I. Remove retaining strip on top of drum.
2. Remove 114-20 screen-retaining screws (six pieces) and lock washers.
3. Remove the old screen and replace it with new.
4. Replace six 1/4-20 flat head screen retaining screws.
5. Replace retaining strip on top of drum.
H-4215 Parts
H-4215 Additional Parts
Warranty
Humboldt Mfg. Co. warrants its products to be free from defects in material or workmanship. The exclusive remedy for this warranty is Humboldt Mfg. Co., factory replacement of any part or parts of such product, for the warranty of this product please refer to Humboldt Mfg. Co. catalog on Terms and Conditions of Sale. The purchaser is responsible for the transportation charges. Humboldt Mfg. Co. shall not be responsible under this warranty if the goods have been improperly maintained, installed, operated or the goods have been altered or modified so as to adversely affect the operation, use performance or durability or so as to change their intended use. The Humboldt Mfg. Co. liability under the warranty contained in this clause is limited to the repair or replacement of defective goods and making good, defective workmanship.
Humboldt Mfg. Co.
875 Tollgate Road Elgin, Illinois 60123 U.S.A.
Testing Equipment for
HUMBOLDT
www.humboldtmfg.com
U.S.A. Toll Free: 1.800.544.7220
Voice: 1.708.456.6300
Fax: 1.708.456.0137
Email: hmc@humboldtmfg.com
Construction Materials
Loading...