Humboldt H-3625 User Manual

09.09

product manual

H-3620, H-3624, H-3625

Flow Table

with Mold

Introduction

These Flow Tables are constructed in accordance with the current ASTM Specification
C 230, using the inch-pound units for the tables, and for accessory sets of molds and
calipers, both inch-pound and metric (SI) units.

Models Shipping Wt.

H-3624 Flow Table, Motorized, with automatic counter (110V, 60Hz) 108 lbs. (49kg)
H-3624.5F, same H-3624 except (220VAC, 50 Hz, 1 ph) 118 lbs. (53.5kg)
H-3625 Flow Table, Motorized (110V, 60Hz) 100 lbs.(45kg)
H-3625.5F, same as H-3625 except (220 VAC, 50 Hz, 1 ph) 110 lbs. (49.9kg)
H-3620 Flow Table, Hand driven 30 lbs. (13.6kg)

Components and Accessories (ordered separately):
H-3622 Mold (English)

H-3622M Mold (Metric)
H-3621 Caliper (English)
H-3621M Caliper (Metric)
H-3623 Circular shield, for use with molds to protect table top from mortar spills.
H-4144 Straight edge, for cutting off mortar flush with surface of mold.
H-3614 Automatic counter kit

General Information

Inspection:

Your Flow Table was thoroughly inspected before it was shipped and should be ready to
operate after it is properly mounted (see below). Notify Humboldt Mfg. Co. or your local
agent and file claim with any carriers involved if you find any damage to the machine.

Physical Specification:

Shipping weight (see above)
Overall height, table & frame: 9 ¾" (25 cm) approx.
Diameter of table top: 10" (25.4 cm)
Base plate: 10" x 10" x 1" (25.4 x 25.4 x 2.54 cm)

Power Supply:

110 VAC 60 Hz 1 phase (H-3624&H-3625), 200 watts
220 VAC 50 Hz 1 phase (H-3624.5F&H-3625.5F), 200 watts

Initial Installation

Remove the packing list and verify that all parts have been received. Normally you will
receive the product complete in one carton.

It is necessary to mount the base plate to which the flow table is mounted to the top
of a concrete pedestal using ½" (13mm) bolts imbedded at least 6" (150mm) into the
pedestal. The pedestal is to be cast inverted on the base plate such that positive contact
is maintained at all points between the base plate and pedestal (dimensions are as
described in ASTM C230).

The motor mounting and supporting plate is attached to the side of the pedestal
as shown with 5/16" (8.5mm) imbedded studs or anchored bolts. Use the attached
template to mark the hole pattern.

When the concrete is cured insert the proper ½ " (13mm) padding or pads under the
pedestal.

After mounting, tighten all fasteners (20 ft. lb. torque or 27 NM) and check to see the
able top is level along two diameters in both the raised and lowered positions.

Operation

Depending upon the model purchased operation are the following:

1. By hand (cranking clockwise).

2. By actuating the switch (on the motor line-cord) to the desired count or

3. By presetting and actuating the automatic counter. If the latter, see instructions
attached for the H-3614 Automatic Counter Kit.

Prior to an actual test raise and permit the table to drop a dozen times or more just
prior to use if it has not been operated in some time.

Perform a calibration test to check for satisfactory operation of the flow table using a
suitable calibration material.

Refer to the appropriate ASTM or AASHTO specification for conducting tests, e.g., for
testing the Air Content of Hydraulic Cement Mortar follow the procedure outlined in the
current issue of ASTM Specification C185.

CAUTION: Keep hands, clothing and other objects away from moving parts when the
machine is in operation.

Maintenance

The table top and vertical shaft must be kept clean and the vertical shaft lightly
lubricated with a light oil (SAE-10), which must not flow into the mating frame and
table top surfaces.

To facilitate easy starting and reduce wear apply a light film of oil to the crown of
the cam, being careful to keep it off of the mating frame and table top surfaces.

H-3620

H-3624

H-3625

Warranty

Humboldt Mfg. Co. warrants its products to be free from defects in material or
workmanship. The exclusive remedy for this warranty is Humboldt Mfg. Co., factory
replacement of any part or parts of such product, for the warranty of this product please
refer to Humboldt Mfg. Co. catalog on Terms and Conditions of Sale. The purchaser is
responsible for the transportation charges. Humboldt Mfg. Co. shall not be responsible
under this warranty if the goods have been improperly maintained, installed, operated
or the goods have been altered or modified so as to adversely affect the operation, use
performance or durability or so as to change their intended use. The Humboldt Mfg. Co.
liability under the warranty contained in this clause is limited to the repair or replacement
of defective goods and making good, defective workmanship.

Humboldt Mfg. Co.

875 Tollgate Road
Elgin, Illinois 60123 U.S.A.

U.S.A. Toll Free: 1.800.544.7220

Voice: 1.708.456.6300

Fax: [phone]

Email: [e-mail]