◆ Complies with IEEE 802.11g;
802.11b; 802.11n ; 802.11a ;802.11ac
standard for 2.4GHz and5GHz Wireless
LAN.
◆TWO Transmit and TWO Receive
path(2T2R)
◆Supports Ad-Hoc/Infrastructure modes
◆ Works with all existing network
nfrastructure.
◆Capable of up to 128-Bit WEP
Encryption.
◆Freedom to roam while staying
connected.
◆ Compatible with IEEE 802.11ac
standard to provide wireless 866.7Mbps
date rate.
◆ Operating Systems:Windows XP
32/64,2000,Windows 7,Vista
32/64,Linux,Macintosh
◆ Low power consumption.
◆ Easy to install and configure.
1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,9
0,120 and maximum of 300Mbps
QPSK , BPSK , CCK(802.11b)
QPSK , BPSK , 16QAM ,64QAM with OFDM
(802.11g)
BPSK , QPSK , 16QAM ,64QAM with
OFDM(802.11n)
QPSK , BPSK , 16QAM ,64QAM with OFDM
(802.11a)
QPSK , BPSK , 16QAM ,64QAM,256QAM
with OFDM(802.11ac)
2.4GHz: CH 1~CH13 for FCC
5GHz: 5150~5250MHz,
5725~5850MHz
Up to 300 meters in open space
Windows XP 32/64,2000,Windows 7,Vista
32/64,Linux,Macintosh
WEP, TKIP, AES, WPA, WPA2
-10 ~ 70°C ambient temperature
-55 ~ 125°C ambient temperature
PRODUCTS USERMANUAL
WIFI Module
IEEE 802.11b/g/n/a/ac
Model Number:
WC3XM2001
2T/2R
The WC3XM2001 is a high-gain and low power consumption wifi module . It fully complies with
IEEE 802.11n and IEEE 802.11b/g/a/ac feature rich wireless connectivity at high
standards,delivers reliable,cost-effective,throughput from an extended distance.When
3.3V, USB bus and GND were connected,This module is working.
PAGE 1 OF 3
PRODUCTS USERMANUAL
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the
user documentation that comes with the product. Modular could be only used in mobile or fix device, and could not be
used in any portable device.
The module must be installed in TV set.
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another
transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including
the transmitter) and obtaining a separate FCC authorization.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user authority to operate the equipment.
Regulation information
(1) This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
(2) This compliance to FCC radiation exposure limits for an uncontrolled environment, and minimum of 20cm
separation between antenna and body.
(3) The device is going to be operated in 5150~5250MHz frequency range. It is restricted indoor environment only.
(4) Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove
this RF module in the user’s manual of the end product which integrates this module.
(5) The end product must carry a label stating “Contains FCC ID: 2AC23-WC3XM2001” or shall use e-labeling.
PAGE 2 OF 3