HUIZHOU GAOSHENGDA TECHNOLOGY W7BM1100 User Manual

Hui Zhou Gaoshengda Technology Co., LTD W7BM1100

Version 1.0

Product Name

WIFI Module

Model

W7BM1100

Standard

802.11 b/g/n

Interface

USB

Data Transfer Rate

1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90 and maximum of 300Mbps

Modulation Method

DQPSK,DBPSK,CCK(802.11b)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11g)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n)

Frequency Band

2412~2462 MHz

Operation Mode

Infrastructure

Security

WEP, TKIP, AES, WPA, WPA2

Operating Voltage

3.3V±10%

Current Consumption

＜1000mA

Antenna Type

PIFA

Operating
Temperature

0 ~ 60°C ambient temperature
Storage Temperature

-40 ~ 80°C ambient temperature

Humidity

5 to 95 % maximum (non-condensing)

Product Features

Product Description

◆ Complies with IEEE 802.11b/g/n for 2.4GHz Wireless LAN.

◆One transmit and One receive path(1T1R)

◆ Works with all existing network nfrastructure.

◆Capable of up to 128-Bit WEP Encryption.

◆Freedom to roam while staying connected.

◆ UP to 150Mbps High-Speed Transfer Rate in 802.11n mode of operation.

◆ Operating Systems：Android,Linux,Win7,XP

◆ Low power consumption.

◆ Easy to install and configure.

◆ High speed USB 2.0 interface

◆ ROHS compliant

Product Specification

WIFI Module
IEEE 802.11 b/g/n

Model Number:

W7BM1100

1T/1R

The W7BM1100 is a 2.4GHz WIFI 1×1 module. The WLAN operation supports 20MHz,40MHz channels for data
rates up to 150Mbps. It fully complies with IEEE 802.11 b/g/n feature rich wireless connectivity at high
standards,delivers reliable,cost-effective, throughput from an extended distance.

PAGE 1 OF 2

Hui Zhou Gaoshengda Technology Co., LTD W7BM1100

Version 1.0

FCC Statement

List of applicable FCC rules

This device complies with FCC part 15C : 15.247.

Specific operational use conditions

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. And the module should be installed at a minimum
distance of 20 cm away from person nearby. The host product manufacturer should state this information to the host instruction manual.

Limited module procedures： Not applicable.
Trace antenna designs：Not applicable.
FCC Radiation Exposure Statement

This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

Antenna Information

Antenna Type: PIFA Antenna
Antenna Gain: 3.52 dBi
The antenna is permanently attached and not consideration of replacement.

Label and compliance information

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also
display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID:2AC23-W7BM1100 Or
Contains FCC ID:2AC23-W7BM1100”.

Information on test modes and additional testing requirements

Any final host product with the modular transmitter installed should be under test according to guidance given in KDB 996369 D04. To enter test mode for module, a QA
TOOL software is necessary. When something wrong happens in configuring test modes for host product with module, host product manufacturer should coordinate with
module manufacturer for technical support. It is recommended that some investigative measurements should be taken to confirm that host product with module installed does
not exceed the spurious emissions limits or band edge limits.

Part 15 Subpart B disclaimer

The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) list on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed when contains digital circuity.

Canada Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :

1)L'appareil ne doit pas produire de brouillage;

2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC:12290A-W7BM1100” any
similar wording that expresses the same meaning may be used.

l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précédé des mots « Contient un module d'émission », du mot «
IC:12290A-W7BM1100 » ou d'une formulation similaire exprimant le même sens, comme suit

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and
compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir

PAGE 2 OF 2