HUIZHOU GAOSHENGDA TECHNOLOGY W2T User Manual

Hui Zhou Gaoshengda Technology Co., LTD W2TM2510

p

WIFI Module
IEEE 802.11 b/g/n 2T/2R
Model Number: W2TM2510

Product Descrition

The W2TM2510 is a 2.4GHz 2×2 MIMO WIFI module. This module provides a high level of integration with a dual-stream IEEE

802.11n MAC/ base band /radio.The WLAN operation supports 20MHz,40MHz channels for data rates up to 300Mbps. It fully
complies with IEEE 802.11 b/g/n feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput
from an extended distance.

Product Features

◆ Complies with IEEE 802.11b/g/n for 2.4GHz Wireless LAN.

◆Two transmit and Two receive path(2T2R)

◆ Works with all existing network nfrastructure.

◆Capable of up to 128-Bit WEP Encryption.

◆Freedom to roam while staying connected.

◆ UP to 300 Mbps High-Speed Transfer Rate in 802.11n mode of operation.

◆ Operating Systems：Linux,Win7, Win8, Win10,XP

◆ Low power consumption.

Easy to install and configure.◆
High speed USB 2.0 interface◆
ROHS com

liant◆

Product Specification

Model WIFI Module
Product Name W2TM2510

Standard 802.11 b/g/n
Interface USB
Data Transfer Rate 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90 and maximum of 300Mbps
Modulation Method DQPSK,DBPSK,CCK(802.11b)

Frequency Band 2400~2483.5 MHz
Frequency Range:
Antenna Type: PIFA Antenna
Antenna Gain:

Operation Mode Infrastructure
Security WEP, TKIP, AES, WPA, WPA2
Operating Voltage 3.3V±10%
Current Consumption
Antenna Type PIFA
Operating Temperature 0 ~ 60°C ambient temperature

QPSK,BPSK,16QAM,64QAM with OFDM (802.11g)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n-HT20)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n-HT40)

2412~2462 MHz

Chain 0
Chain 1

＜1000mA

2dBi
2dBi

Storage Temperature -40 ~ 80°C ambient temperature
Humidity 5 to 95 % maximum (non-condensing)

FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247

PAGE 1 OF 3

Version 1.0

Hui Zhou Gaoshengda Technology Co., LTD W2TM2510

NOTICE:

◆ please keep this product and accessor ies attached to the places which children can't touch;

◆ do not splash water or other liquid onto this product, otherwise it may cause damage;

◆ do not put this product near the heat source or direct sunlight, otherwise it may cause deformation

◆ or malfunction;

◆ please keep this product away from flammable or naked flame;

◆ please do not repair this product by yourself. Only qualified personnel can be repaired.

FCC Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
We will retain control over the final installation of the modular such that compliance of the end product is assured. In such cases, an operating condition

on the limit modular approval for the module must be only approved for use when installed in devices produced by a specific manufacturer. If any
hardware modify or RF control software modify will be made by host manufacturer,C2PC or new certificate should be apply to get approval,if those
change and modification made by host manufacturer not expressly approved by the party responsible for compliance ,then it is illegal.

The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between
the radiator and user body.

If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter
Module FCC ID:2AC23-W2T Or Contains FCC ID:2AC23-W2T”

When the module is installed inside another device, the user manual of the host must contain below warning
statements;

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with

the product.
Any company of the host device which install this modular with limit modular approval should perform the test of radiated & conducted emission and

spurious emission,etc. according to FCC part 15C : 15.247 and 15.209 & 15.207 ,15B Class B requirement, Only if the test result comply with FCC part
15C : 15.247 and 15.209 & 15.207 ,15B Class B requirement，then the host can be sold legally.

not cause harmful

PAGE 2 OF 3

Version 1.0