HUIZHOU GAOSHENGDA TECHNOLOGY W2N User Manual

Hui Zhou Gaoshengda Technology Co., LTD W2NM2510

p

WIFI Module
IEEE 802.11 b/g/n 2T/2R
Model Number: W2NM2510

Product Descrition

The W2NM2510 is a 2.4GHz 2×2 MIMO WIFI module. This module provides a high level of integration with a dual-stream IEEE

802.11n MAC/ base band /radio.The WLAN operation supports 20MHz,40MHz channels for data rates up to 300Mbps. It fully
complies with IEEE 802.11 b/g/n feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput
from an extended distance.

Product Features

◆ Complies with IEEE 802.11b/g/n for 2.4GHz Wireless LAN.

◆Two transmit and Two receive path(2T2R)

◆ Works with all existing network nfrastructure.

◆Capable of up to 128-Bit WEP Encryption.

◆Freedom to roam while staying connected.

◆ UP to 300 Mbps High-Speed Transfer Rate in 802.11n mode of operation.

◆ Operating Systems：Linux,Win7, Win8, Win10, XP

◆ Low power consumption.

Easy to install and configure.◆

◆High speed USB 2.0 interface

ROHS com

Product Specification

Model WIF Module

liant◆

Product Name W2NM2510
Standard 802.11 b/g/n
Interface USB
Data Transfer Rate 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90 and maximum of 300Mbps
Modulation Method DQPSK,DBPSK,CCK(802.11b)

Frequency Band 2400~2483.5 MHz
Frequency Range: 2412~2472 MHz
Antenna Type: PIFA Antenna
Antenna Gain:

Operation Mode Infrastructure
Security WEP, TKIP, AES, WPA, WPA2
Operating Voltage 3.3V±10%
Current Consumption
Antenna Type PIFA
Operating Temperature 0 ~ 60°C ambient temperature

Storage Temperature -40 ~ 80°C ambient temperature
Humidity 5 to 95 % maximum (non-condensing)

QPSK,BPSK,16QAM,64QAM with OFDM (802.11g)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n-HT20)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n-HT40)

Chain 0
Chain 1

＜1000mA

2dBi
2dBi

PAGE 1 OF 3

Version 1.0

Hui Zhou Gaoshengda Technology Co., LTD W2NM2510

NOTICE:

◆ please keep this product and accessories attached to the places which children can't touch;

◆ do not splash water or other liquid onto this product, otherwise it may cause damage;

◆ do not put this product near the heat source or direct sunlight, otherwise it may cause deformation

◆ or malfunction;

◆ please keep this product away from flammable or naked flame;

◆ please do not repair this product by yourself. Only qualified personnel can be repaired.

FCC Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipme nt.

Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authorit y to

operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

If power exceeds the limit and the distance（Over 20cm distance in actual use between the device and user） is compliant with the

requirement

FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Notice to OEM integrator
The end user manual shall include all required regulatory information/warning as show in this manual.
The OEM integrator is responsible for testing their end-product for any additional compliance
requirements required with this module installed.
If the FCC ID is not visible when the module is installed inside another device, then the outside of the
device into which the module is installed must also display a label referring to the enclosed module.
The end product shall haves the words “Contains Transmitter Module FCC ID: 2AC23-W2N”.

The device must be professionally installed
The intended use is generally not for the general public.It is generally for industry/commercial use.

The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally

required. the user has no access to the connector.

Installation must be controlled. Installation requires special training

Canada Statement:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical specifications were met.

This product meets the applicable Industry Canada technical specifications.
Le présent appareil est conforme aux CNR d'Industrie Canada applicable aux a ppareils ra dio exempts de licence. L'exploitation est

autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement

PAGE 2 OF 3

Version 1.0