Huffy 2002 User Manual

1
08/02 P/N 211981
Customer Service Center
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A Huffy Company
MODEL:___________________
Internet Address: http://www.huffysports.com
In U.S. and Canada only: IMPORTANT! Don’t go back to the store!
We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. We regret that although great care and effort have been taken, occasionally problems may occur. To ensure prompt and correct handling of any problems, or to answer any questions, please contact our Toll-Free Customer Service Number listed below. Service will be quicker if
you have your Model Number (found on carton) and assembly instructions ready when calling. PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE.
REQUIRED TOOLS AND
MATERIALS:
• Step Ladder 8 ft. (2.4m)
• Adjustable Wrench
• Wrenches: (One) 3/4” (Two) 1/2”
• Phillips Screwdriver
Composite Framed Acrylic Backboard
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these
rules for safe operation of the unit.
To ensure safety, do not attempt to assemble this system without fol­lowing the instructions carefully. Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document. Proper and complete assembly, use and supervi­sion is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly.
• Read and understand the warning label enclosed with hardware. It is the responsibility of the customer to mount this label. It should be affixed to the pole, wall, or door near playing area, at a height between 4­6 feet above ground level and in a location visible to all players.
• During assembly, if using a ladder use extreme caution. Two people are recommended for this operation.
• If technical assistance is required, contact Huffy Sports.
• Serious injury could occur if teeth/face come in contact with backboard, net or rim.
• Minimum operational height is 6’ 6” to the bottom of backboard.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
WARNING
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT
IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Owner must ensure that all players know and
follow these rules for safe operation of the unit.
In the U.S.: 1-800-558-5234 and Canada Only: 1-800-284-8339
In Australia: 1-800-632-792
206118 5/97
See instruction manual for proper installation and maintenance. Use caution when performing dunk type activities on this unit. Do not hang from any part of unit, including backboard, support braces, rim or net. Check unit before each use for loose hardware, excessive wear and signs of corrosion and repair before using. During play, use extreme caution to keep player's face away from the backboard, rim or net. Serious injury could occur if teeth/face come in contact with backboard, rim or net. During play, do not wear jewelry (rings, watches, necklaces, etc.) Objects may entangle in net.
·
·
·
·
·
·
© COPYRIGHT 2002 by HUFFY SPORTS
2
P/N 211981 08/02
PARTS LIST - See Hardware Identifier
Item #2 (4)
Item #3 (4)
Item #5 (6)*
Item #7 (12)*
Item #4 (4)
Item #10 (4)
Item Qty.
Part No. Description
1 1 206118 Warning Label 2 4 201611 Hex Flange Bolt 5/16-18 x 3 Long 3 4 203104 Hex Flange Bolt 5/16-18 x 2 Long 4 4 203309 Washer, 1 O.D. 5 6* 203100 Hex Flange Nut, 5/16 x 18 61 Rim 7 12 201219 Clips, Net Holder Smart Clips 8 1 204281 Net 9 2 200533 Spacer, Board Mount
10 4 205528 Bolt, Hex Head, 5/16-18 x 1
* You may have extra parts with this model.
ASSEMBLY INSTRUCTIONS
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL
WARNING: TWO PEOPLE ARE NECESSARY TO MOUNT THE BACKBOARD ASSEMBLY TO SUPPORT STRUCTURE. ONE PERSON SHOULD NOT ATTEMPT TO DO THIS ALONE.
WARNING: MOUNTING THE BACKBOARD ASSEMBLY TO THE SUPPORT STRUCTURE IS PERFORMED AT AN ELEVATED HEIGHT. USE PROPER PRECAUTION.
WARNING: IT IS RECOMMENDED TO MOUNT BACKBOARD TO A SOLID (STEEL) SUPPORT.
1. Attach Backboard and rim using one of the options as shown.
WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT
PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY.
2. Install net clips as shown (See Illustration).
3. Install net as shown (See Illustration).
4. Place warning label (1) in location clearly visible within playing area.
1. Mounting Options “A, B or C”
HARDWARE IDENTIFIER
Loading...
+ 4 hidden pages