Hudson Valley 5219 User Manual

5216 & 5219

Hudson Valley Lighting, Inc.

P.O. Box 7459
106 Pierces Road
Newburgh, NY 12550
[phone]
www.hudsonvalleylighting.com

GENERAL

1. To ensure the success of the fixture installation, the following
instructions and diagram(s) should be read and understood.

2. All electrical connections must be made in accordance with the
National Electric code and local codes and ordinances. If you are
uncertain of the methods of installing electrical wiring and lighting
fixtures secure the services of a qualified licensed electrician.

3. TOOLS NEEDED: Blade screwdriver, phillips screwdriver,
slip joint pliers or small adjustable wrench, wire cutter/stripper,
electrical current tester, stepladder and electrical tape. NOTE: The
important safeguards and instructions outlined on this sheet are
not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care
are factors that cannot be built into any product. Caution and care
must be supplied by the person(s) installing, operating and
maintaining this lighting fixture.

INSTALLATION PREPARATION

1. TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH
THE LIGHTING FIXTURE IS TO BE ATTACHED. Move the

appropriate circuit breaker to the “off position or completely remove
the fuse controlling the circuit.

2. If an existing fixture is being replaced, remove it and note to
which of the wires in the outlet box the fixture was attached. DO

NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE
BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING. In regular

circumstances the BLACK wire will be the “Hot” lead and the
WHITE wire will be the “Neutral” or “Common” lead. A GREEN or
BARE COPPER wire is the “Ground”. In older buildings it is always
good practice to reconfirm the polarity of the wiring.

3. This fixture is designed to be mounted on a standard round or
octagon box. The box must be securely mounted to the structure
of the building.

FIXTURE PREPARATION

1. Remove the fixture, shades and parts bag(s) from the carton.
Before discarding the carton, double check packing to make
certain that all parts are found.

2. Assemble the stem, scroll and loop assembly to the fixture body.

FIXTURE INSTALLATION

1. Attach the crossbar to the outlet box. (The green screw should
face the floor)

2. Remove the threaded ring from the screwcollar loop. Fully
thread the loop onto the nipple. Thread the hex nut onto the
nipple and the nipple into the crossbar. Place the canopy over the
screwcollar loop and against the ceiling. Adjust the nipple so that
¼” of threads on the screwcollar loop extend beyond the canopy.
Tighten the hex nut against the crossbar.

3. Open end links of chain to the screwcollar loop. Close the top
link of chain. Hang the fixture on the chain at the desired height.
Remove the excess chain. Close the bottom link of chain.

Outlet box

Green screw

Crossbar

Nipple

Canopy

Screwcollar loop

ring

Chain

Approved fastener
(Wire nut)

Electrical tape

5206

5209

Hudson Valley Lighting, Inc.

P.O. Box 7459
106 Pierces Road
Newburgh, NY 12550
[phone]
www.hudsonvalleylighting.com

5216 & 5219
(Continued)

4. Unscrew the ring from the screwcollar loop. Let the ring and
canopy slide down the chain to the top of the fixture. Thread the
lead wires and ground wire (first) through the ring and then the
canopy. Thread the wires up through alternating links of the chain to the outlet
box.

5. Measure 6” of lead wire beyond the end of the chain. Cut off
excess wire. Strip the insulation off the ends of the leads exposing
approx. ½” of wire. Twist the strands of wire together. Push the
leads and ground wire up through the screwcollar loop and nippke and into the
outlet box.

6. Fasten the green fixture wire to the green or bare copper wire
in the box or fasten it to the mounting plate with green screw
provided. NEVER FASTEN THE GROUND WIRE TO THE

BLACK OR “HOT” WIRE! FAILURE TO FOLLOW THIS
INSTRUCTION COULD RESULT IN SERIOUS INJURY OR
DEATH!

7. Fasten the white fixture wire to the white wire in the outlet box.
Fasten the wires to together with an approved fastener (wire nut).
Starting about 1” below the fastener, tightly wrap connection with
electrical tape so that the tape seals the end of the fastener.
Make sure that there is no exposed wire or strands that could cause a
dangerous short circuit !

8. Connect the smooth fixture wires to the black wire in the outlet
box. Fasten the joined wires as in step 7.

9. Slide the canopy and screwcollar ring up the chain and secure
the canopy to the ceiling.

10.Thread the fixture loop onto the fixture.

11.Twist the fixture body onto the nipple on the wire box.

12. Place the shades into the socket sleeves.
.

13. Install the lamp(s).
NOTE: This fixture is rated for 60 watt type B, BA, C or CA lamp(s).

DO NOT EXCEED RECOMMENDED WATTAGE !

14. Restore power to circuit at breaker or fuse box.

Fixture loop

Fixture body

Fixture loop

Fixture body