Hudson Valley 4614 User Manual

4610, 4614 & 4620

Mounting Plate

Stem

Canopy

Swivel

Ground Screw

Mounting Screw

Outlet Box

Nut

Stems

Glass

Lamp

Glass Ring

Fitting

Shade

Thumb Screw

GENERAL

1. To ensure the success of the fixture installation, the following instructions and
diagram(s) should be read and understood.

2. All electrical connections must be made in accordance with the National Electric
code and local codes and ordinances. If you are uncertain of the methods of
installing electrical wiring and lighting fixtures secure the services of a qualified
licensed electrician.

3. TOOLS NEEDED: Blade screwdriver, phillips screwdriver, slip joint pliers or
small adjustable wrench, wire cutter/stripper, electrical current tester, stepladder
and electrical tape. NOTE: The important safeguards and instructions outlined on
this sheet are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care are factors that
cannot be built into any product. Caution and care must be supplied by the
person(s) installing, operating and maintaining this lighting fixture.

INSTALLATION PREPARATION

1. TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH THE LIGHTING

FIXTURE IS TO BE ATTACHED. Move the appropriate circuit breaker to the “off

position or completely remove the fuse controlling the circuit.

2. If an existing fixture is being replaced, remove it and note to which of the wires
in the outlet box the fixture was attached. DO NOT SEPARATE ANY OTHER

WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF

OLDER WIRING. In regular circumstances the BLACK wire will be the “Hot” lead

and the WHITE wire will be the “Neutral” or “Common” lead. A GREEN or BARE
COPPER wire is the “Ground”. In older buildings it is always good practice to

reconfirm the polarity of the wiring.

3. This fixture is designed to be mounted on a standard round or octagon box. The
box must be securely mounted to the structure of the building.

4. This fixture is supplied with a 5- piece stem. There is one 3” section, one
6” section, one 12” section and two 18” sections.

FIXTURE INSTALLATION

1. Remove the fixture, shades and parts bag(s) from the carton. Before discarding
the carton, double check packing to make certain that all parts are found.

2. Remove the 2 nuts holding the mounting plate to the fixture. (Starting at back),
thread the 2 longest mounting screws into the mounting plate, (The green screw
is in the front). Attach the mounting plate to the outlet box. (The green screw
should face the floor).

3. Thread the small hex nuts onto the mounting screws. Lock the hex nuts against
the mounting plate.

4. Thread lead ground wire through pipe stem and twist tightly onto body. Keep
adding additional stems required.

5. Thread wire through canopy and carefully slide over stem.

6. Install ball swivel on end of stem.

7. Trim excess wire to min 6” beyond stem, strip 5/8” and twist.

8. Slide the canopy up and be sure to align tab with groove in ball swivel.

9. Fasten the green fixture wire to the green or bare copper wire in the box or
fasten it to the mounting plate with green screw provided.

NEVER FASTEN THE GROUND WIRE TO THE BLACK OR “HOT” WIRE!
FAILURE TO FOLLOW THIS INSTRUCTION COULD RESULT IN SERIOUS

INJURY OR DEATH!

10. Fasten the white fixture wire to the white wire in the outlet box. Fasten the wires
to together with an approved fastener (wire nut).
Starting about 1” below the fastener, tightly wrap connection with electrical tape so
that the tape seals the end of the fastener.
Make sure that there is no exposed wire or strands that could cause a dangerous
short circuit !

11. Connect the black fixture wires to the black wire in the outlet box.
Fasten the joined wires as in step 10.

12. Position and mount canopy to outlet box at ceiling with the nuts.

13. Twist the fitting part onto the end of the stem.

Electrical tape

Approved tape
(Wire nut)

Hudson Valley Lighting, Inc.

P.O. Box 7459
106 Pierces Road
Newburgh, NY 12550
[phone]

www.hudsonvalleylighting.com

14. Install the lamps (light bulbs).
NOTE: 4610 is rated for 100 watt Type A lamps.
4614 is rated for 150 watt Type A lamps.

4620 is rated for 150 watt Type A lamps.

DO NOT EXCEED RECOMMENDED WATTAGE !

15. Place the glass onto glass ring, press the clips to hold the glass, put the glass
ring to the shade and use thumb screw to lock it tight.

16. Put the shade to the fitting, and twist it to the correct position when the tab holds the
shade.

17. Restore power to the circuit at breaker or fuse box.