Hubsung Plastics HUSKY24G Users Manual

Order Number : GETEC-C1-10-196 FCC Part 15 subpart C
Test Report Number : GETEC-E3-10-126 Page 1 / 1

APPENDIX H

: USER’S MANUAL

EUT Type: 2.4 GHz FHSS Transmitter

FCC ID.: RE6HUSKY24G

hook

Approval

- FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device

may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that

may cause undesired operation.

Any changes or modifications not expressly approved by the party responsiblefor compliance could void the

authority to operate equipment.

The antenna(s) used for thistransmitter must not be co-located or operating inconjunction with any otherantenna or
transmitter.

- Federal Communication Commission (FCC) Radiation Exposure Statement
For Husky 2.4G, transmitter : FCC ID RE6HUSKY24G
The remote device is approved as hand-held and hand-operation only portable (relative to hand)
device which is normally operated at 5 cm from a person's body
For Cube 3, receiver : FCC ID RE6CUBE24G3
The device and the antenna for this device must be installed to ensure a minimum separation
distance of 20 cm or more from a person's body. Other operating configurations should be avoided.

- CE
Hereby, Hubsung Plastics Ltd. declares that this 2.4 GHz radio control system is in comd and
compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

The R&TTE (Radio Equipment & Telecommunications Terminal Equipment) directive is the new
European directive relating to radio equipment and telecommunications transmission equipment. It
also covers the collective recognition of the conformity of such equipment. One part of the R&TTE
directive regulates the introduction and operation of radio systems in the European Community. An
important change is the abolition of approval. The manufacturer or importer must subject radio
equipment to a conformity appraisal process before that equipment is introduced. The CE symbol is
attached to the device to indicate that it conforms with the valid European norms.

An exclamation mark is also to be attached to radio transmitting equipment, to indicate that the
permissible frequencies are not yet uniform throughout Europe. This requirement applies to all the
countries included in the list attached. It is essential to note that these radio control systems may
only be operated on the approved frequencies, as listed in the table.

Please note that the user bears the responsibility for compliance with this requirement, and for
ensuring that the radio system complies with the directives. In Germany the requirement to purchase
a license for the operation of 2.4 GHz systems remains in effect; please refer to the operating
instructions, or the separate sheet included with them.

Proton Radio Control, Inc.

PO Box 957681 Duluth GA USA 30096

Charging takes approximately 2 hours.

power LED

charger into the charging port on the side.
the battery installed in HUSKY 2.4G, plug the
Use the charger included in this product. With

- Charging

3. Close the cover.

USB port
battery pack is tightly sit.
b

ottom and slide towards the front so that the

2. Place the Li-ion battery pack (NB-2LH) in the

open the cover.

1. Lightly press the hook and pull up the tap to

Li-ion Battery Installation and Charging

Battery box

.

2. Power the Cube receiver and press the bind button (red LED above the slots) until the

C

o

charging port

AUX & Power slot

power switch

Throttle servo slot

Steering servo slot

Rear View

Bind button

wheel to left or right.

o reactivate the touch sensor buttons, simply rotate the steering

inactivity. T
automatically deactivated and go into hold mode after 10 seconds of

avoid an unintended operation, touch sensor buttons are

Important Note: To
require a light finger touch to operate.
* Touch button : The control buttons are touch sensors and they only

C

o

720mAh)

LED changes to blue. 3. Confirm the link establishment by watching for servo movement when steering or triggering.
Linking procedure: 1. From the transmitter's [BIND] menu, choose ID LINK and press Enter
Once the link is made, the ID code is stored in the receiver and no further linking is necessary unless the receiver needs to be used with another transmitter.
Each transmitter has an individually assigned unique ID code. In order to start operation, the receiver must be linked with the ID code of the transmitter to which it is being paired.

How to establish link between the transmitter and the receiver

Operating temperature : 0 ~ 40
Power requirements : DC 3.5 ~ 10.0 V
We

ight : 14.80 g (0.52 oz)

Size : 38 X 30.5 X 16.5 mm (1.5" X 1.2" X 0.65")
Modulation : 2.4 GHz, FHSS

Specification of Cube 3, receiver

Cube 3, Antenna-less Receiver

Operating temperature : 0 ~ 40
(DC 7.4 V,
Power requirements : Li-ion battery pack
We

ight : 482 g (17 oz)

(7.28" X 4.72" X 10.63")
Size : 185 X 120 X 270 mm
Modulation : 2.4 GHz, FHSS

Specification of Husky 2.4G, transmitter

4. Reinstall the 4 screws.

connectors inside.

Body

body. Be carefully not to bend the pin
carefully reinsert the control panel into the

degrees and

o

3. Rotate the control panel 180

slowly pulling apart.

2.4G

HUSKY

2. Separate the control panel and the body by

1

Trigger

button
Stopwatch

control panel.

1. Remove the 4 screws from the bottom of

tap

2

Loading battery pack

Steering wheel

Panel

Control

and/or loss of signal.
damage the connections, causing reduced range
and reinstall can loosen the antenna base and
installed, leave it installed. Repeated removal
Caution: Do not over tighten the antenna. Once

Touch buttons*

LCD

Antenna

User's Guide

+, - / dual rate

up / start

down / idle

M

enter / stopwatch

mode

steering trim

Antenna Installation

trim
throttle

Top View

Adaptation for Left-hander