Hubsung Plastics CUBE24G3 Users Manual

Order Number : GETEC-C1-10-197 FCC Part 15 subpart C
Test Report Number : GETEC-E3-10-127 Page 1 / 1

APPENDIX H

: USER’S MANUAL

EUT Type: 2.4 GHz FHSS Transmitter

FCC ID.: RE6CUBE24G3

Cube 3

3 Channel 2.4 GHz Transceiver

User's Guide

Cube 3 (Transceiver, Antenna-less design)

Cube 3 is the first-ever, revolutionary micro receiver with the antenna-less design. Cube 3 is a 3-channel, 2.4GHz receiver, utilizing
FHSS (Frequency Hopping Spread Spectrum) technology, which allows accurate and detailed controls, without the trouble of
interferences.

ntenna-less design

- A
Cube 3 is the first-ever R/C receiver product that does not have an external wire antenna. Because of its antenna-less design,
Cube 3 allows for an extremely flexible and simple installation, without having to hassle with wire antenna, tubes, eta.

- Bidirectional Communication
Cube 3 is capable of transmitting data back to the transmitter.
transmitter to avoid battery troubles.
Notice : Cube 3 is designed for use on surface models only.

Specification

Modulation : 2.4 GHz, FHSS
Size : 38 X 30.5 X 16.5 mm (1.5" X 1.2" X 0.65")

ight : 14.80 g (0.52 oz)

We
Power requirements : DC 3.5 ~ 10.0 V
Operating temperature : 0 ~ 40oC

Cube 3 sends its battery voltage information in real-time to the

Bind button

Steering servo slot

Throttle servo slot

AUX & Power slot

Installation

1. Clean surface on the model where Cube 3 is to be mounted. 2. Mount Cube 3 with Velcro tape (included).

3. Put servo plugs into slots 1 & 2, power plug into slot B. (Ken receiver accepts Futaba, JR, Hitec, new KO and Sanwa Z connectors)

How to establish link between the transmitter and the receiver

Each transmitter has an individually assigned unique ID code. In order to start operation, the receiver must be linked with the ID
code of the transmitter to which it is being paired. Once the link is made, the ID code is stored in the receiver and no further linking
is necessary unless the receiver needs to be used with another transmitter.
Linking procedure: 1. From the transmitter's [BIND] menu, choose ID LINK and press Enter.
the bind button (red LED above the slots) until the LED changes to blue. 3. Confirm the link establishment by watching for servo
movement when steering or triggering.

Approval

FCC, ID : RE6CUBE24G3

-

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:(1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interferencethat may cause undesired operation.
Any changes or modifications not expressly approved by the party responsiblefor compliance could void the authority to operate equipment.The antenna(s) used for this
transmitter must not be co-located or operating inconjunction with any otherantenna or transmitter.The antenna(s) used for this transmitter must not be co-located or operating
inconjunction with any otherantenna or transmitter.

- Federal Communication Commission (FCC) Radiation Exposure Statement
The device and the antenna for this device must be installed to ensure a minimum separation distance of 20 cm or more from a person's body. Other
operating configurations should be avoided.

- CE
Hereby, Hubsung Plastics Ltd. declares that this 2.4 GHz radio control system is in comd and compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
The R&TTE (Radio Equipment & Telecommunications Terminal Equipment) directive is the new European directive relating to radio equipment and
telecommunications transmission equipment. It also covers the collective recognition of the conformity of such equipment. One part of the R&TTE
directive regulates the introduction and operation of radio systems in the European Community. An important change is the abolition of approval. The
manufacturer or importer must subject radio equipment to a conformity appraisal process before that equipment is introduced. The CE symbol is
attached to the device to indicate that it conforms with the valid European norms.

2. Power the Cube receiver and press

An exclamation mark is also to be attached to radio transmitting equipment, to indicate that the permissible frequencies are not yet uniform
throughout Europe. This requirement applies to all the countries included in the list attached. It is essential to note that these radio control systems
may only be operated on the approved frequencies, as listed in the table.

Please note that the user bears the responsibility for compliance with this requirement, and for ensuring that the radio system complies with the
directives. In Germany the requirement to purchase a license for the operation of 2.4 GHz systems remains in effect; please refer to the operating
instructions, or the separate sheet included with them.

Proton Radio Control, Inc.

PO Box 957681 Duluth GA USA 30096