Hubsan NANO Q4 SE, H001 User Manual

HUBSAN NANO Q4 SE

ITEM NO: H001

www.echothree.co.uk

INTRODUCTION

Thank you for buying this Hubsan product. This specific model is a user friendly multi-functional

RC quadcopter, with full 4-channel control capable of acrobatic manoeuvres. Please read the manual carefully and follow all the instructions. Be sure to keep the manual for future reference.

1. Safety Notes

1.1 Important Notes

This multi-functional RC quadcopter is not a toy.

To prevent injury from improper operation please read these instructions carefully. Be aware of your personal safety, safety of others and your surrounding environment. It is recommended that beginners should learn to fly the quadcopter under the guidance of a more

experienced

user.

1.2 Caution

Propellers work at high speed which may cause injury with improper use. The user is responsible for any damage caused by improper use. Do not operate the quadcopter in crowds, buildings, airports or near any high voltage cables.

1.3 Li-Po battery safety notes

The quadcopter is powered by a

Lithium-Polymer

battery. If you plan to not use the quadcopter for a prolonged period of time then store with the battery at approximately 50% charge to maintain battery life and performance.

Important

● Risk of explosion if the battery is replaced by an

unauthorized

battery.

● Dispose used batteries according to the local regulation

1.4 Prevent moisture

The quadcopter contains many precision electrical components. Store the product in a dry area at room

temperature.

Exposure to water or moisture

may cause malfunction and result in loss of control.

1.5 Always be aware of the rotating propellers

Be careful to keep yourself away from the rotating propellers. Always fly the quadcopter in sight. To prevent any damage or harm, power off the quadcopter and the remote controller immediately after use.

1.6 Avoid flying alone

Beginners should fly under supervision.

1.7 Changing controller batteries

The remote control requires 2 x AAA batteries (not included)

2. Items in the Box

Check all the items in the box before use.

S/N Part Name Photos Quantity Remarks

1 Quadcopter 1

Equipped

with

1 x Li-Po

Battery

2 Propellers 8

Propeller

A: 4pcs

Propeller

B: 4pcs

3 Remote

Controller

1

Requires

2 x AAA Batteries

(Not

Included)

4

USB Charger 1

For

recharging

the

Li-Po

Battery

5

Manual

1

Quick Guide Instruction

3. Safety check before flying

● Before flight, make sure the batteries of the quadcopter and the controller are fully charged.

● Before powering on the remote controller, make sure the throttle stick is at the lowest position.

● Turn on the

quadcopter

first then power on the transmitter.

● After operating the drone, you must turn off the quadcopter first then the transmitter. The wrong sequence could cause damage to the

quadcopter

and

surroundings

due to lack

of control.

4. Charge the Li-Po Battery

Connect the quadcopter to the Hubsan USB charger, then connect the USB charger to a USB

port, such as a computer or mobile power charger.

It takes approximately 30 minutes to fully charge the battery. The USB LED indicator will stay red whilst the quadcopter is charging and will turn off when it is fully charged. Please unplug the charger and battery when charging is completed. Flight time is around 5 minutes.

The battery should only be charged with the HUBSAN charger to avoid

overcharging

or damage to the battery.

5. Propellers

(1) Attach the

propellers

to the

corresponding

motors that

are

marked

A and B;

A=A B=B

(2)

Tighten

the

propellers

to the motor shaft.

● Make sure that the A and B

propellers

are

installed correctly.

The

quadcopter

will not fly if propellers are improperly installed.

6. Remote Controller

5 LED Indicator

1

Throttle/ Rudder

Stick

2

Elevator/Aileron

Stick

4

Throttle/ Rudder

Trim 3

Elevator/ Aileron

Trim

4 Power Switch

6.1 Input Key Function

S/N

Mode/ Control

Function

1

Throttle/ Rudder Stick

Push the stick

forward

or

backward

and the quadcopter

will

ascend

or

descend;

Push th e stick left or right and the

quadcopter

will rotate left or right.

2

Elevator/ Aileron Stick

Push the stick

forward

or

backward

and the quadcopter

will fly

forward

or

backward; Push

the stick left or right

and the

quadcopter

will fly left or right.

3

Elevator Trim

Adjusts

for

forward

and

backward

drift.

4

Aileron Trim

Adjusts

for left and right drift.

5

LED Indicator

Flashing red before binding; Constant red LED

after binding.

6

Power Switch

Turn on/off the

remote

controller.

● Do not mix old and new batteries ● Do not mix different types of batteries

● Do not charge

non-rechargeable

battery.

6.2

Quadcopter

calibration

Quadcopter calibration

is

required

when the

quadcopter

drifts during flight.

Land the

quadcopter

and place it on a

horizontal/flat surface

for calibration.

Calibrating

procedures:

Push the left stick to the bottom right

corner,

and move the right stick from left to right

quickly and repeat until the 4 LED

indicators

on

quadcopter

flash alternately.

Calibration

is

completed

when the

indicators

stop flashing.

7. Start to Fly

7.1 Power-On

The quadcopter is designed with a Power-On safety system, it ensures the motors will not start unless safety signals are detected.

7.1.1 First power on the quadcopter, then pull the throttle stick to the lowest position and power on the

transmitter.

Before the

quadcopter

and the

transmitter

are

successfully

bound together, do not move the joysticks or press any of the buttons, otherwise the quadcopter could be unstable.

7.2 Basic Flight

Transmitter

Quadcopter

Operation

Up

The throttle stick controls the ascent and descent of the Q4. Push the stick up to ascend the Q4. Pull the stick down to descend the Q4. Move the throttle stick above center position to take off. Move the stick gradually to prevent the Q4from

ascending

too

quickly.

Right Rotation

Left Rotation

The rudder stick controls the rotation of the Q4. Push the stick to the left and the Q4 will rotate counterclockwise. Push the stick to the right and the Q4 will rotate clockwise. Pushing harder will cause the Q4 to rotate faster in the corresponding

direction.

Forward

Backward

The

Elevator

stick

moves

the Q4 forward and backward. Push the stick up the and the Q4 will fly forward. Pull the stick down and the Q4 will fly backward. The angle of stick

movement corresponds to the angle of tilt and flight speed.

Right

Left

The

Aileron

stick

controls

left and right flight. Push the stick to the left and the Q4 will fly to the left. Push the stick to the right and the Q4 will fly to the right. The angle of stick

movement

corresponds

to the

angle of

tilt and flight

speed.

7.3

Headless

mode

Headless mode means the Q4 will set the current direction as the default direction. When you choose a default headless mode, your Q4 will always move to the left of that default direction when you pull your aileron stick to the left and move to right when you pull the aileron stick to the right

regardless

of where the drone is pointing at. In headless mode, the 2 LED in the front will blink simultaneously. Short press the Throttle stick for to enter/exit headless mode.

Short press the Throttle stick to enter into the headless mode, indicated by two beeps. Short press the Throttle stick again to exit the headless mode, indicated by one beep.

8. Advanced performance setup

Normal Mode/ Expert

Mode

The default setting is Normal Mode, and the Expert mode can be

activated

to increase the

sensitivity

of the

remote control

sticks.

Aerial Flip Mode

Long press the throttle stick to enter Flip Mode, indicated by a beep sound. The beep sound will last for 2 seconds. Within this 2 second period, push the elevator stick to perform a flip.

8.1 Forward flip

Push the elevator stick forward quickly then release the stick.

8.2 Backward flip

Push the elevator stick backward quickly then release the stick.

8.3 Left flip

Push the elevator stick left quickly then release the stick.

8.4 Right flip

Push the elevator stick right quickly then release the stick.

Flip

Mode

is not

available when battery

is low.

S/N

Part Name

Qty

07

Li-Po

Battery

1

08

Lower Body

Shell

1

09

Screw

PA1.0*4

4

3. Exploded View

1

2

3

5

4

5

6

7

8

9

S/N

Part Name

Qty

01

Propeller

A

2

02

Propeller

B

2 03

Upper Body

Shell

1 04

Motor

A

2

05

Motor

B

2

06

PCBA

1

H001

TROUBLESHOOTING

1.

Transmitter

and

Quadcopter cannot

pair

Throttle stick needs to be at the lowest position. Please do not move or press the sticks and trims during the initial

power-on

binding.

2.

Gyroscope

not working.

a) Battery voltage

is too low. b) Re-bind. c) Land

the

quadcopter

on the

ground

with the throttle stick at the lowest

position

and wait for

3

seconds

then take off.

3.

Unable

to flip

Battery voltage

is too low.

4.

Quadcopter

is

shaking

or

making

noise

during

flight

Check

if the

motors, body shell

and

propellers

are

properly positioned, then check

if the motors

or

propellers

are damaged.

5.

Propellers

work well, but

cannot

take off

a)

Propellers

were not

installed properly.

Make sure that

propeller

A and B are installed accordingly. b) Motors were not

installed properly.

Make sure motor A and B are

installed

accordingly.

6. One or more

motors stopped

working

a) Check if

propellers

were

installed

too tight.

7. The

quadcopter

is drifting

Calibrate

as

instructed

below:

a) Make sure the

propellers, motors

and

quadcopter

are in a good

condition,

the

battery

is fully

charged

and

connected correctly

and the

quadcopter

is bound to the

remote

controller.

b)

Calibrating

procedures: Push the left stick to the bottom right corner, and move the right stick from left to right quickly and repeat until the 4 LED indicators on quadcopter blink alternately. Calibration is

completed

when the

indicators

stop blinking.

All Ri

ghts

Reserved

WWW.HUBSAN.COM

VERSION 1.3

EN