HUBBELL LIGHTING WP9S II, WP9L II, WP9S III, WP9L III, WP9S IV Installation Instructions Manual

17760 Rowland Street
City of Industry, CA 91748
626/369-2695

WARP9

WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical Code.

!

Failure to do so may result in serious personal injury.

MAINTENANCE: A regularly scheduled maintenance program should be established to retain

!

optimum light output and reduce heat retention. Dusting with a soft, clean, dry cloth is normally

®

- WP9L / WP9S Installation Instructions

WP9LE
WP9LM

WP9SE
WP9SM

sufficient for the reflector. Any accumulation of dust or dirt should be removed regularly from both sides
of the lens during re-lamping (using ammonia water). Do Not use alkaline or acid cleaners on reflector
surfaces.

Kim Lighting recommends mounting WARP9 luminaires on round poles to further improve aerodynamics
and lend to the fixture’s camouflaged appearance. Round poles have less visual signature than
square poles.

NOTE: All wiring must be done by a qualified electrician.

KEEP THIS SHEET FOR FUTURE REFERENCE.

Parking lots and roadways require luminaire on 20’ - 40’ poles to efficiently light these large areas. Pedestrian areas
require poles to decrease in height to 10’ - 16’. Avoid installing pole-mounted luminaires close to the building, as they
tend to dominate the architecture.

Attention: If your fixture is equipped with a multi-tap ballast and if no voltage was specified on the purchase order, the
ballast has been wired for operation on a 277 volt circuit (347V in Canada). If other than 277 volts is required, i.e.; 208V,
240V, connect incoming voltage lead to required voltage on terminal block.

INSTALLATION INSTRUCTIONS: Make certain electrical supply is OFF before starting fixture.

!

Tools Required: q N” Socket Wrench q B” Allen Wrench

C” Bolt
Attachment

1. Lay pole horizontal on padded supports
to protect finish. Pull field wires
through pole and out the top. Tie-wrap
wires to pole backing plate. Tie wires
in a knot or back loop through
tie-wrap.

2. Attach fixture assembly to pole
(2 places) using washer and C” bolt.
Be sure fixture is aligned with anchor
base and other fixtures for multiple
mounts. Tighten to 20 ft.-lbs. using

N” socket wrench.

3. Install arm access cover and secure

with self retained screw using a
B” Allen wrench.

1/18/17 EC 170118003 Rev 6 93012589

®

WARP9

- WP9L / WP9S Installation Instructions

INSTALLATION INSTRUCTIONS (cont.)

Disconnect
Plug

Disconnect

Plug

4. Slide latch back to open ballast
compartment. Use both hands as the
ballast cover swings down. Make
sure ballast cover is properly seated in
hinges. Caution: Magnetic ballasts are
heavy use both hands.

7. Swing ballast cover up to close.

Caution: Magnetic ballasts are heavy
use both hands to close.

5. Join the disconnect plug halves between
the socket & the ballast assembly and
the disconnect plug halves between the
power lead-in & the ballast assembly.
(Electronic Ballast Shown)

8. Connect fixture wires to field wires
observing polarity, i.e.; green-to-ground,
white-to-common and black-to-voltage.

LAMP INSTALLATION and REPLACEMENT INSTRUCTIONS:

6. Always make sure retention cable is

attached before closing up LED driver
compartment.

9. Tuck all wires inside pole and install
the no-tool pole cap by snapping into
place.

Latch

10. Open lens frame assembly by pressing
latch in housing and with other hand
hold lens frame so it swings gently down.

© 2017 KIM LIGHTING • 17760 Rowland Street • City of Industry, CA 91748 • 626.369.2695 Page 2

11. Carefully unclip the retention cable to
lower lens down for lamp replacement.

12. Install the proper lamp, as per fixture
label on reflector, into the socket &
tighten the lamp sufficiently to ensure
a vibration safe installation.