Page 1
Hubbell Lighting, Inc.
LED Replacement
Contact factory
SERVICE
PGF1 LED Wallpack
High Performance LED Wallpack For Indoor
Or Outdoor Application
Installation, Operation and Service Instructions
RECYCLING INFORMATION
All steel, aluminum and thermoplastic parts
are recyclable.
All cartons contain recycled materials.
Please recycle responsibly.
PATENTS
PENDING
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following.
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. Do not let power supply cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.
4. The use of accessory equipment not authorized by the manufacturer may cause an
unsafe condition.
5. Do not use this equipment for other than its intended purpose.
6. Servicing of this equipment should be performed by qualified service personnel.
Copyright© Hubbell Lighting, Inc., All Rights Reserved • Specications subject to change without notice. • Printed in U.S.A.
Hubbell Lighting, Inc. Life Safety Prducts • www.dual-lite.com
93036067 11/ 11
93021413
93021935
93021938
93021939
93036084
93036085
93036096
INSTALLER:
•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
WARNING – This product contains chemicals known to the State of California to cause cancer, birth
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,
or otherwise touching this product.
Page 2
Screw
O-Ring
Backplate
93021938
INSTALLATION
1.Open the unit by loosening both screws on top of unit until screws spin freely. Pry cover
from backplate, and remove cover squarely from backplate. (Remove screws prior to
re-installing cover.)
IMPORTANT:
Once unit is connected and cover is snapped onto backplate, gently seat screws onto
O-ring seals to less than 1/2FT-LB (.7N-m).
DO NOT OVERTIGHTEN!
O-RING MAY BE DAMAGED AND THE UNIT WILL LEAK IF ABOVE IS NOT
FOLLOWED.
Unit will operate from 120 or 277VAC through 2 wire intelligent input.
OPERATION
Photo-cell option: Unit will operate on 120VAC only, through 2 wire input.
Cover
2.Remove 7/8” diameter K.O. from backplate if mounting to electrical
box or remove 1/2”-1/4NPT pipe plug if using conduit.
CONDUIT MOUNTING:
If unit is not secured to mounting surface using unit backplate
K.O. pattern and supplied gasket, use sealant to create
waterproof seal between the mounting surface and the unit
backplate.
IMPORTANT!
To weatherproof your outdoor installation, be sure to seal all
fixture openings - mounting, conduit, etc.
3.Remove appropriate backplate K.O.’s
93036085
for electrical box screws.
6.Connect building AC wires to
AC harness wires.
4.Peel backing from J-Box Gasket and adhere to
backplate around center K.O.
93021935
5.Feed building wires through center K.O. as
shown and secure backplate using screws
supplied with electrical box.
120VAC
277VAC
Ground
NOTE:
Feed wires and nuts back into electrical box through
backplate as shown.
Connect black (hot) and neutral (white)
to supply.
Connect black (hot) and neutral (white)
to supply.
Connect ground (green) conductor.
AC Wire Harness
To Building Ground Wire
7.Connect AC wire harness to AC wire harness
on unit backplate.
93036084
9.Attach unit cover to backplate by
reversing Step 1. Ensure all wires
are within enclosure to avoid pinching
with cover.
Full Cut-off Shield Installation Photo-Cell Option
TABS “A”
Pinch sides inward
1.Slide tabs “A” between housing and lens gasket.
2.Pinch sides of shield inward and seat shield against lens.
3.Release pinched sides of shield to secure to unit.
There will be a delay of up to 2 minutes to prevent false switching due to
momentary flashes of light.
9303609693021939
Loading...