Hubbell Lighting SLS-2 CIRCUIT BALLAST User Manual
INSTALLATION INSTRUCTIONS FOR
SLS TWO CIRCUIT REMOTE BALLAST SYSTEM
Catalog Logic: R E M D - X X X X H X - XX - XX
Fixture Watts:
1000 1500 1650
Fixture Voltage:
(2) 208v (3) 240v
(4) 277v (5) 480v
Circuit No. 1 & 2 Ballast Qty:
51 42 33 41 32 31 22 21 11
Optional Features:
(SH) Solution Harness Ready
(TB) **Thermal Magnetic Breaker
**Standard for 240v and below
(WP) Wood or other Solid Pole
(T) Wire Three Phase
3/8"
TYP.
3/8"
3"
41"
5"
4-7/8"
A complete system includes the ballast enclosure, lighting
fixtures, wiring harness, crossarms and poles.
Warning!
• Dangerous voltages exist within this product.
• This enclosure includes two electrical supply circuits. To
reduce fire and shock hazards disconnect power to both
circuits before servicing.
• To reduce the risk of injury, operate and maintain to meet
all applicable codes.
• Installation is to be performed by a qualified electrician
only.
• Provide proper ground for all system components.
• Read and follow all instructions and labels before and during installation.
• Failure to properly install this product will void
manufacturer’s warranty.
• Handle and secure so ballast enclosure cannot fall.
• Use protective equipment to avoid injury during installation of this heavy product.
• Do not route wiring through top of enclosure.
This ballast enclosure should be installed at a minimum
➞
height of 10 feet (3 meters) above grade.
COUPLING W/ 3/4-10
INTERNAL THREADS
FOR 3/4" BOLT
FIGURE 1
4
3
2
Enclosure Installation (Figures 1, 2, & 3)
Important: Installation requires the use of a pole equipped
with mounting couplings and wireway. (Figure 1)
1. Remove peel strip from gasket supplied in hardware bag.
2. Apply gasket to the back of enclosure around the 2-1/2"
x 4-1/2" (63.5mm x 114.3mm) hole. (Figure 3)
3. Install bolt (2) and lockwasher (3) in the top coupling.
(Figure 2) Leave 1" (25.4mm) of thread exposed.
2
3
5
FIGURE 2
268-1220-9901
4. Position lift bracket (4) over the bolt (2) and lockwasher
(3). NOTE: The top of keyhole in bracket must contact
the bolt to support the 280 pound (127Kg) enclosure.
5. Align the wireway opening in the enclosure with the wire-
way opening in the pole. Do not damage gasket!
6. Install bolt, lockwasher and flatwasher through hole in-
side the enclosure and into the coupling in pole.
7. Tighten the both bolts to a minimum of 40ft/lbs.
8. Seal all openings between pole and enclosure.
Wiring and Electrical Instructions
✔ The enclosure includes two electrical supply circuits.
✔ The enclosure voltage must match the supply voltage.
✔ Standard wiring is single phase. Enclosure is wired
three phase when a “-T” is in the catalog number.
✔ T otal operating amps for each supply circuit is shown on
the electrical datamarker located near each switch.
✔ Enclosures are factory wired to operate as a separate
unit. (Contact factory for wiring multiple enclosures in
series).
✔ Factory fusing of all branch circuits is included.
✔ Separate internal electrical switching is included for each
circuit:
• Thermal Magnetic Breaker is standard for 208v,
220v and 240v
• Load Break Switch is standard for 277v, 347v and
480v
• “-TB” in catalog number indicates Thermal Magnetic
Breaker for 277, 347v and 480v.
CLOSE GAPS
FIGURE 3
“-SH” HARNESS
PLUG
Supply Wiring:
1. Connect customer supply wires to circuit #1 or circuit #2
switch as appropriate.
2. Connect ground wire (6) to the ground lug (7).
3. Provide effective strain relief to prevent wire damage.
4. Comply with all national and local electrical codes.
Caution: Protect exposed wires with approved insulators.
Fixture Wiring into Enclosure:
1. Connect the male plug of the wiring harness to the female harness plug inside enclosure. (Figure 4) Snap securely .
2. Enclosure shall be properly grounded.
3. Close door and engage the latches. A lock is optional.
These instructions are not intended to be a comprehensive
guide to all Installation issues.
The installer is responsible for sale, secure mounting suitable for the application.
Once the enclosure is installed, give these instructions to
the equipment owner.
CIRCUIT #2
SUPPLY
LEADS 7
CIRCUIT #1
SUPPLY
LEADS
FIGURE 4
268-1220-9901
Loading...