HUBBELL LIGHTING PGL51/61, PGL52/62, PGL53/63, PGL54/64, PGL55/65 Installation Instructions Manual

PGL5/6 - Parking Garage Luminaire Installation Instructions

P.O. Box 60080 • 16555 East Gale Ave.
City of Industry, California 91716-0080
626/968-5666 • FAX [phone]

Revised 7/16/10 ECN 100715008 Status 7 Part No. 95667

WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical Code.
Failure to do so may result in serious personal injury.

CAUTION: All wiring should be done by a qualified electrician. DO NOT operate luminiare with missing or
damaged lens.

KEEP THIS SHEET FOR FUTURE REFERENCE.

Attention: If your fixture is equipped with a multi-tap

ballast and if no voltage was specified on the purchase
order, the ballast has been wired for operation on a 120 or
277 volt circuit (347V in Canada). If other than 120 or 277
volts is required, i.e.; 208V, 240V, see Ballast Wiring
Information on page 4.

WARNING

Never energize fixtures with plastic
bag - installed for protection during
construction or painting. This will
cause permanent damage from
overheating.

PREPARING FOR INSTALLATION:

Tool Required: Flat Blade Screwdriver

Step 1 - Verify fixture locations: To assure a correct installation, the specifier should key the fixture locations on the

garage plan with the icon for a PGL51/61, PGL52/62, PGL53/63, PGL54/64, PGL55/65, PGL56/66, PGL57/67,
or PGL58/68.

PGL51/61 PGL52/62

PGL53/63

PGL54/64

PGL55/65

PGL56/66 PGL57/67 PGL58/68

SHOWN ARE THE LIGHT PATTERNS FOR EACH FIXTURE.

PGL51/61
PGL52/62
PGL53/63
PGL54/64
PGL55/65
PGL56/66
PGL57/67
PGL58/68

!

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

IMPORTANT SAFETY INSTRUCTIONS!

WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical Code.
Failure to do so may result in serious personal injury.

MAINTENANCE: Parking garages are open structures, fixtures will eventually become dirty with air and
exhaust pollutants. A regularly scheduled maintenance program should be followed. The PGL5/6 is rated to
IP66, allowing power washing; a fast and effective way to keep the fixtures at peak efficiency.

CAUTION: All wiring should be done by a qualified electrician. Lighted lamp is HOT! DO NOT operate
luminaire with missing or damaged lens. KEEP THIS SHEET FOR FUTURE REFERENCE.

Page 2 Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone]

PGL5/6 - Parking Garage Luminaire Installation Instructions

!

2. Make electrical connections
observing polarity; i.e., green-to­ground, white-to-common, and
black-to-voltage.

1. To hang fixture, slide the
suspension strap onto the wire
retainer on the speed mount
plate. Allow fixture to hang freely.

FIXTURE CONNECTION TO SPEED MOUNT & FINAL INSTALLATION:

Make certain electrical supply is OFF before starting installation.

Wire
Retainer

Suspension
Strap

!

Attach Kim

Speed Mount

to J-Box

Bind Head Screws must be
used in the installation of the
Kim Speed Mount.

Preparing For Installation cont'd.

Step 2 - Install the Kim speed mount to the J-box. The

Kim Speed Mount must be installed in accor­dance with the label. Be certain Kim speed
mount is installed with the driving direction &
parking stalls in the correct orientation.

DO

NOT put washers under screw heads.

Step 3 - Remove the tape that holds the suspension

strap to the fixture.

J-Box

Tuck All
Leads And
Connections
Into J-Box

Suspension

Strap

Fixture

Wires

Locking
Tab

3. Swing fixture away from j-box
center and up against ceiling and
speed mount plate while feeding
wires into j-box. It is important

to keep tension on the
suspension strap as the fixture
is raised.