Hubbell Electric Heater J310.4 Installation Manual

OPERATING AND MAINTENANCE

MANUAL FOR

ELECTRIC BOOSTER HEATER

ELECTRIC HEATER COMPANY

BASE MODEL “ J ”

2014 Edition Rev. A

UM ANSI/NSF5

1

HUBBELL

ELECTRIC HEATER COMPANY

45 SEYMOUR STREET

P.O. BOX 288

STRATFORD, CT 06615

PHONE: [phone]
FAX: [phone]

INTERNET: http://www.hubbellheaters.com

-- IMPORTANT --

ays reference the full model number and serial number when calling the factory.

Alw

WARNING / CAUTION

1. Tank is to be completely filled with water and all air is to

be vented before energizing.

2. Due to the rigors of transportation, all connections should be checked for tightness before
heater is placed in operation.

3. Safety relief valve m

ust be

4. The refractory material used in heating elem
transit, periods of storage, or when subjected to a hum
absorption results in a cold insulation resistance of less than twenty
heater has been subjected to the above condition, each heating elem

installed in tapping provided.

ents may absorb some mo

id environment. This mo

isture during

isture

(20) megohm

ent mu

st be checked

s. If this

for insulation resistance before energizing. Contact the factory for a replacement element.

5. KEEP AWAY FROM LIVE ELECTRICAL CIRCUITS.
Do not perform

any maintenance, make any adjustments, or replace any com

ponents
inside the control panel with the high voltage power supply turned on. Under certain
circum

stances, dangerous potentials may exist

even when the power supply is off. To
avoid casualties, always turn the power supply safety switch to off, turn the charge or
ground the circuit before perform

ing any maintenance or adjustme

nt procedure.

6. The unit is designed to operate at pressure not more than 150 psi.

7. Generalized instructions and procedures cannot anticipate all situations. For this reason,

only qualified installers should perform

the in

stallations. A qualified installer is a person
who has licensed training and a working knowledge of the applicable codes, tools,
equipm

ent, and methods necessary for safe

installation of an electric resistance water
heater. If questions regarding installation arise, check your local plumbing and electrical
inspectors for proper procedures and codes. If you cannot obtain the required
information, contact the company.

8. Water Quality Requirements – Recommended wa

ter hardness is 4 to 6 grains of
hardness per gallon (GPG). Water hardness above 6 GPG should be treated by a water
conditioner (water softener or in-line treatment). Water hardness below 4 GPG also
requires treatm
operating and m

ent to reduce potential corrosi

on. Excessive GPG will result in higher

aintenance costs and will reduce product longevity. Chlorides mu

st
not exceed 50 parts per million (ppm). Excessive chlorides will result in metallic
corrosion and will reduce product longevity. Water treatment has been shown to
reduce costs associated with de-lim

ing the booster as well as reducing me

tallic
corrosion. Product failure caused by these conditions is not covered under warranty.
See warranty for complete details.

9. This water heater is not intended for space heating applications.

10. The water heater is factory set at 185°F for booster water heating applications. This

results in the possibility of a scalding water injury. A full thickness skin burn can
occur in less than one second of exposure to water at this temperature.

2

TABLE OF CONTENTS

SECTION TITLE

I GENERAL DESCRIPTION AND CONSTRUCTION 4

II INSTALLATION AND START-UP 9

III SCHEDULED MAINTENANCE AND OPERATION 24

IV TROUBLESHOOTING 26

V SERVICING AND REPLACEMENT OF PARTS 32

VI SERVICE PARTS LIST 35

VII TORQUE VALUES 37

VIII WARRANTY INFORMATION 38

PAGE No.

3

SECTION I - GENERAL DESCRIPTION AND CONSTRUCTION

GENERAL DESCRIPTION

This book describes a packaged electric booster heater that is typically used to provide 180°F
sanitizing rinse water. The complete assembly consists of the storage tank, immersion electric
heating element(s), electronic control module, safety relief valve, magnetic contactor(s), and
any other required electrical operating control. Optional equipment may be supplied with your
unit. Please consult the product packing list for details specific to your assembly. The unit is
factory assembled, insulated, jacketed, wired, tested, and ready for electrical and plumbing
service connections.

CAPACITY

Storage

Model

J32.9 3 2.9 30 17 J161 16 1 10 5
J35.7 3 5.7 58 33 J161.5 16 1.5 15 8

J39.9 3 9.9 101 58 J162 16 2 20 11
J310.4 3 10.4 107 61 J163 16 3 30 17
J311.4 3 11.4 117 67 J164 16 4 41 23

J411 4 11.4 117 67 J166 16 6 62 35
J415 4 15 154 88 J167 16 7 72 41
J427 4 27 277 158 J169 16 9 92 53

J61 6 1 10 5 J1612 16 12 123 70

J61.5 6 1.5 15 8 J1613 16 13.5 138 79

J62 6 2 20 11 J1615 16 15 154 88
J63 6 3 30 17 J1618 16 18 185 105
J64 6 4 41 23 J1624 16 24 246 141
J65 6 5 51 29 J1627 16 27 277 158
J66 6 6 62 35 J1630 16 30 308 176
J67 6 7 72 41 J1636 16 36 369 211

J69 6 9 92 53 J1639 16 39 400 228
J610 6 10.5 108 62 J1640 16 40.5 415 237
J612 6 12 123 70 J1645 16 45 461 264
J613 6 13.5 138 79 J1654 16 54 554 316
J615 6 15 154 88 J1658 16 58.5 600 343
J618 6 18 185 105 J1664 16 64 656 375
J624 6 24 246 141 J1666 16 66 677 387
J627 6 27 277 158 J1668 16 68 697 398
J630 6 30 308 176 J1679 16 79 810 463
J636 6 36 369 211 J1681 16 81 830 474
J639 6 39 400 228 J1685 16 85 871 498
J640 6 40.5 415 237 J1686 16 86 882 504
J645 6 45 461 264 J1688 16 88 902 515
J654 6 54 554 316 J1690 16 90 923 527
J658 6 58.5 600 343

Capacity

(gallons)

kW

40°F

Rise

(GPH)

70°F

Rise

(GPH)

Model

Storage

Capacity

(gallons)

kW

40°F

Rise

(GPH)

70°F

Rise

(GPH)

4

56 7

CONSTRUCTION
TANK

The storage tank is designed, manufactured, and stamped in accordance with ASME Section
VIII, Division 1. The tank is constructed of type 304L stainless steel for maximum tank
longevity and fabricated by all welded construction and is designed for a maximum allowable

working pressure of 150 psi (225 psi test pressure).

TANK CONNECTIONS

The heater is supplied with separate connections for the cold/warm inlet and the hot water
outlet. Water entering the warm water inlet and leaving through the hot water outlet is evenly
circulated by means of a diffuser within the tank. A ¾-inch FNPT connection is provided for
mounting a combination temperature and pressure safety relief valve. An overflow line should
be utilized from the relief valve outlet to a floor drain. See drawing for locations and sizes.

HEATING ELEMENT

The water heater is supplied with an electric
immersion heating element assembly(s), composed
of corrosion resistant sheathed elements that are
fitted into a 1½-12UNF brass screw plug with a
1⅞” hex. Each assembly is threaded into the tank and sealed with an o-ring gasket. See drawing
for voltage and power ratings. Note that the J3 model element is a 1” NPS thread with a 1½”
hex.

MAGNETIC CONTACTOR

Load switching is done by a heavy-duty resistive (non-inductive)
load type definite purpose magnetic contactor. The contactor supplies
power to the heating element(s) when the relay on the control board
is closed, thereby pulling in the contacts until the desired temperature
is reached. At this point, the contacts will drop out, which in turn
disconnects power from the elements. Units with multiple contactors
will

turn on and off in stages. This contactor is good for 200,000 cycles.

CONTROL BOARD AND DISPLAY

The control board supplies all the
necessary functions for heater operation.
These include control temperature, hi­limit cut-out, low water detection, and
leak detection.

LOW VOLTAGE CONTROL TRANSFORMER

A control circuit transformer is supplied with all models rated
greater than 240-volts. This component is used to step down the
primary power supply (600, 480, 440, 415, 380, or 277) to 208/240­volts for safety when working with control.

POWER CIRCUIT BREAKERS

When required by code, a magnetic power circuit breaker is
supplied for circuit overload protection. The circuit breaker can
be reset in the event of a current overload.

OUTER SHELL, INSULATION, AND SUPPORTS

The tank is encapsulated in high efficiency foam insulation meeting the requirements for UL 94
HF-1 rating. The protective shell is constructed of type 304 brushed stainless steel. NSF
approved adjustable plastic legs are provided for support. Plastic legs for the J3 and J4 models
are optional.

DIAL TEMPERATURE AND PRESSURE GAUGE

A combination temperature (30°-240° F / 0°-120°C) and pressure (0–200 psi
/ 0-1400 kPa) gauge with 3-inch dial is supplied with the unit for in-line

installation (shipped loose). The connection is ½” NPT with a 2” long sensing

probe. For the J3 and J4 models the gauges are optional.

PRESSURE REDUCING VALVE

A bronze pressure reducing valve with built-in bypass is supplied with the unit.
This valve is shipped separately for in-line installation. The ¾” NPT valve is
adjustable from 25-psi to 75-psi (approximately 17-psi to 67-psi including
pressure drop through the valve). The inlet connection is supplied with a ¾”
union by sweat connection. The outlet connection is ¾” female NPT. The set
screw located at the top of the diaphragm adjusts the pressure, turn clockwise to
decrease the pressure and counter-clockwise to increase the pressure. Pressure
reducing valves for the J3 and J4 models are optional.

DIELECTRIC UNIONS

Dielectric unions are provided for the inlet and outlet nipples to isolate stray
ground currents to reduce the possibility of galvanic corrosion. (Optional on the
J3 and J4 Models).

OPTIONAL EQUIPMENT

Slide Brackets
Available for the J6 Model only, these brackets allow for mounting the booster heater under a
counter. See slide bracket diagram on page 9 for details.
Shock Absorber
The optional shock absorber can be installed between the booster and the
dishwasher to reduce the harmful pressures resulting from quick closing
dishwasher solenoid valves.

Legs
In lieu of the standard black plastic legs,
optional adjustable legs are available in
stainless steel, die-cast nickel plated, and
floor mount stainless steel. All optional legs
are adjustable height type. Floor Mount Nickel Plated Stainless Steel
Security Package
For prison and other secure facilities a tamper resistant package is available. All external screws are
spader type requiring a spader wrench for removal.
Alternate Voltage
Other voltages are available, including 277V single-phase, and 380V, 415V, and 440V three-phase.
Consult the factory for details.
Water Treatment System
The optional water treatment system provides superior mineral scale
prevention and corrosion control by feeding a special blend of scale
control compounds into the warm water stream before the heater. The in­line system includes a clear cartridge housing to allow an operator to view
the cartridge and determine when it needs replacement without the need to
open the system.
XB1 Expansion Board
An optional expansion board to the control board can be used to for additional circuit firing when
more than two circuits are required and/or as an auxiliary high or low temperature alarm/relay. On
models with three contactors the XB1 is supplied as standard.
Remote Alarm Plug Adapter
An optional plug adapter is available to provide a remote fault alarm signal
through the J4 connector on the control board. See page 12 for installation
details.
24-Volt Heater Interlock Adapter
An optional plug adapter is available to interlock the heater via a 24-volt
signal through the J1 connector on the control board. The 24-volt heater
interlock adapter is supplied standard on the J3 model. See page 13 for
installation details. (Only available with r23 or later software).

8

Protective Shrouds (J6 and J16 only)
An optional durable protective plastic shroud is
available to prevent damage to the booster due to
water intrusion. The cover fits snugly over the
entire booster and can be easily removed for
cleaning and service.

SECTION II – INSTALLATION AND START-UP

WARNING / CAUTION

• DO NOT TURN ON THE ELECTRIC POWER SUPPLY to this equipment until

heater is completely filled with water and all air has been released. If the heater is

NOT filled with water when the power is turned on, the heating elements will burn
out.

• For protection against excessive pressures and temperatures, local codes require the

installation of a temperature-and-pressure (T&P) relief valve certified by a nationally
recognized laboratory that maintains periodic inspection of production of listed
equipment of materials, as meeting the requirements for Relief Valves and Automatic
Gas Shutoff for Hot Water Supply Systems. ANSI Z21.22-1971. THE CUSTOMER
IS RESPONSIBLE TO PROTECT PROPERTY AND PERSONNEL FROM HARM
WHEN THE VALVE FUNCTIONS.

• All water heaters have a risk of leakage at some unpredictable time. IT IS THE

CUSTOMER'S RESPONSIBILITY TO PROVIDE A CATCH PAN OR OTHER
ADEQUATE MEANS, SO THAT THE RESULTANT FLOW OF WATER WILL
NOT DAMAGE FURNISHINGS OR PROPERTY.

• Installation or service of this unit requires ability equal to that of a licensed tradesman

in the field.

• The installation must conform to these instructions and any local authority having

jurisdiction. Grounding and electrical wiring connected to the unit must also conform
to the latest version of the National Electric Code NFPA-70.

WATER HEATER PLACEMENT
NOTE: For most effective operation, install the booster heater as close as possible to the

dishwasher. If the distance between the booster and the dishwasher exceeds NSF

requirements, recirculation methods must be employed.

1. Place the heater on a solid, level foundation in a clean, dry location as near as possible

to the dish washing machine.

2. The water heater should be protected from freezing and waterlines insulated to reduce

energy and water waste.

3. Leave a minimum of 18” clearance for element withdrawal and control access.

4. Do not install in an area where flammable liquids or combustible vapors are present.

SLIDE BRACKETS FOR
HANGING SUPPORT
MOUNTING

1. Weld slide rails to

bottom of dishtable.
Spacing should be 17”
for J6 models up to
18kW and 22” for J6
models 24 to 58.5kW.
J16 models are not
designed for use with
slide brackets.

9

2. Attach slide bracket angles to heater with #8 sheet metal screws. It will be necessary

to drill 1/8” holes into heater jacket for screw pilot holes.

3. Slide heater onto slide rails under dishtable.

PIPING INSTALLATION – See Diagrams

NOTES:

• No check valve may be installed in the supply line to the booster.

• All shut-off valves must be gate or ball valves – not globe valves.

• To minimize heat loss and maximize efficiency, hot water piping should be insulated.

• Teflon tape should be used on all NPT threaded pipe connections.

1. Install the factory supplied dielectric unions on the inlet and outlet piping.

2. Connect the cold/warm water inlet and hot water outlet to the appropriate connections

as shown; refer to the specifications for location and sizes.
IMPORTANT – Be certain to connect the outlet piping to the final rinse and not to the
wash tank. Insulate if over 3 feet.
IMPORTANT (applies to J6 Models only) – Do not turn the entering warm water or
exiting hot water nipples from their factory installed positions. The internal diffusers
are aligned at the factory and turning the nipple will change the diffuser position and
affect performance. Hubbell recommends that the inlet and outlet pipes are insulated
to prevent excessive heat loss.
IMPORTANT (applies to J6 Models only) possible to “unsweet” female adaptor
under J16 – Do not apply heat directly to the entering warm water or exiting hot water
nipples. If sweat connections are to be used, sweat tubing to the adapter before
threading the adapter to the nipple on the heater. Any heat applied to the heater nipple
will damage the internal plastic diffuser and affect performance.

3. Install the pressure reducing valve, when supplied, in the entering cold/warm water

inlet line and adjust to 20-psi. The set screw located at the top of the diaphragm adjusts
the pressure, turn clockwise to increase the pressure and counter-clockwise to decrease
the pressure. NOTE: Be sure to install the valve with flow in the proper direction as
indicated by the directional arrow on the valve. IF A STANDARD PRESSURE
REGULATOR IS USED, it acts as a check valve and it is possible that thermal
expansion will cause the relief valve to drip or occasionally blow off a small amount
of water. To overcome this condition, it is recommended that a 3/8” by-pass
arrangement with a horizontal check valve be installed around the pressure regulator.
This will prevent annoyance caused by the relief valve dripping or blowing off.

4. Install the combination temperature and pressure safety relief valve in the tapping

provided. Note that this is required by law for safety considerations.

Install into provided tapping Manual Release Lever

Temperature Probe

Outlet to floor drain

5. Install a relief valve overflow pipe to a nearby floor drain.

NOTE: Relief valve discharge piping limitations:

a. Termination to be plain end (no threads) and 6-inches above the drain.
b. Maximum 30-feet.
c. Maximum four (4) elbows.
d. No reduction in line size.
e. No valve of any type to be installed between the relief valve and tank or in the

drain line.

10

6. A shock absorber is recommended in the hot water outlet line to soften the water

hammer caused by automatic dishwasher solenoid valves.

7. Install the in-line pressure and temperature gauge, when supplied, in the entering

cold/warm water line. If supplied, install the optional second dial temperature and
pressure gauge in the outlet line. The temperature sensing element must be in the hot
water stream and the gauge must be mounted upright.

FILLING THE HEATER

1. Open the valve to the cold/warm water inlet and allow the heater and piping system to

completely fill, as indicated by a steady flow of water through the dishwasher rinse
nozzles.

NOTE: Flush the tank at full flow for 10 minutes prior to putting into service.

ELECTRICAL INSTALLATION

1. Enter the base through the factory cut KO’s with properly sized feeder leads, See

Wiring Chart. Single-phase installations require two (2) leads. All Hubbell 3-phase
heaters are intended for use with a 3-wire delta system plus ground. No neutral is
required. For a 4-wire plus ground system, install 3 legs of power plus the ground and
terminate the neutral leg.

2. Install these power leads into the box lugs on the power distribution block or magnetic

contactor, as required.

3. Connect incoming ground wire to ground lug supplied.

4. Check for proper grounding. Check for AC millivolts (mV) between the ground

connection at the booster and the inlet piping past the dielectric union (on the building
side, not the booster side). There should be zero potential/millivolts (mV). If not
zero, then the piping should be re-grounded.

5. All other electrical connections are made at the factory; therefore, no other electrical

connections are necessary.

6. Check all connections, including factory connections, for tightness.

OPTIONAL XB1 EXPANSION BOARD (used for temperature alarm / interlock)

1. If desired, the XB1 can be used as an alarm relay or a temperature interlock at a

setpoint other than the water temperature setpoint on the booster heater.

2. If the XB1 is not factory installed, mount the XB1 to the control panel and connect the

XB1 to the T1000 control board with the factory supplied cable between JX4 on the
XB1 and J1 and J4 on the T1000 and connect the ground between JX6 on the XB1
and J8 on the T1000.

3. Make connections as required to the relay terminal block. When the temperature drops

below the XB1 setpoint the relay is open between Normally Open (NO) and Common
(C) and the LED will flash green. When the temperature is above the XB1 setpoint the
relay is closed between NO and C and the LED will be solid green. Use NO and C for

11

low temperature interlock or high temperature alarm. Use Normally Closed (NC) and C

ying

for low temperature alarm. A red LED indicates an error.

Note: Alarm Rating (resistive):

Max.: 5A @ 120VAC
5A @ 24VDC

(JX5 L1) Power Wire
(Common, White)

(JX5 L2)Power Wire
(Black)

(JX5) (4) Connections
for Additional Circuit
Firing

(JX2) Low Temp.
Relay Terminal Block

(JX6) Ground

(JX4) Connection to
T1000

(JX3) To be used as
T1000 J1 Connection

(JX1) To be used as
T1000 J4 Connection

LED

Note: Once the XB1 is connected to the T1000 control board, an additional menu option will

be available to set the low temperature setpoint. See Section III.

FOR REMOTE ON/OFF CONTROL

To remotely control the On / Off operation of
the heater, it is recommended that a DPST
switch or relay (by others) be used to break
both power legs (white and black wires)
connected to the top two terminals of the J5
connector on the control board. See diagram at
right.
Use a NC (Normally Closed) relay to turn the
booster ON when energizing the relay coil or
to turn the booster OFF when de-energizing
the relay coil.
Use a NO (Normally Open) relay to turn the booster OFF when energizing the relay coil or

to turn the booster ON when de-energizing the relay coil.
OPTIONAL REMOTE ALARM CONTACTS

1. If desired, the control board can be wired to a remote alarm to indicate a reset fault

condition. These fault conditions include over-temperature, no probe, and low water
(when the configuration is set to manual reset).

2. This alarm can be wired to the J4 connector on the control board as shown below. To

facilitate this installation, an optional adapter, Hubbell P/N PLUG ADAPTER J4, can
be purchased to provide wire connections.

J4 Connector

Note: Rating (resistive)

Max. Switching Power:

60W, 62.5VA

Max. Switching Voltage:

220VDC, 250VAC
Max. Switching Current: 2A
Max. Carr

Current: 3A

PLUG ADAPTER J4

(NO)

(NC)

Note: That when the XB1 expansion board is used, the J4 PLUG ADAPTER should plug
into the JX1 connection on the XB1.

12

OPTIONAL FIELD CONVERSION FROM SINGLE TO THREE PHASE OR
THREE TO SINGLE PHASE (J6 and J16 models in 6, 7, and 9 kW at 208 and 240
volts and J411 models only)

1. Re-wire the unit to desired configuration as indicated below.

NOTE: The wire to be used for internal wiring must conform to SEW-2 or PTFE

(200°C) and must match the wire size currently in use. Contact the factory for
assistance, if required.

2. Contact the factory for correct labels. The factory will need the serial number for

proper identification.

Single-Phase 3-Phase

OPTIONAL 24-VOLT HEATER INTERLOCK ADAPTER

1. If desired, the heater can be wired to operate only when supplied with a 24-volt signal

through the heater interlock adapter. When no 24-volt signal is supplied through the
heater interlock adapter the heater is interlocked and will not energize. When
interlocked the display will show “ HLd”. The heater will resume normal operation
when a 24-volt signal is re-applied through the heater interlock adapter.

2. To utilize this feature, plug the 24-volt heater interlock adapter into terminal J1 of the

T1000 control board (note: if the XB1 expansion board is used, plug the adapter into
terminal JX3 of the XB1) and verify that the configuration is set to “ Hon”, see the
controller operation section for further detail. The signal can be either AC or DC.
However, if a DC signal is utilized and the interlock feature does not operate, switch

the two 24-volt supply wires at the heater interlock adapter.

J1

To J1

To 24-Volt Signal

FINAL CHECKS

1. Check all connections for tightness.

2. Ensure that all the above steps are completed.

3. Remove the protective outer plastic covering from the sheet metal shell.

4. After the water is heated for the first time, monitor the water temperature as described

in Section III, Annual Inspection.

13

J6 and J16 Wiring Chart

Unit

kW Volt Ph

1 120 1 8.3 8.3 14.4 15 12 N/A 14 ½" 1(NT)

1.5 120 1 12.5 12.5 9.6 20 12 N/A 14 ½" 1(NT)
2 120 1 19.8 19.8 6.1 25 12 N/A 12 ½" 1(NT)
3 120 1 25.0 25.0 4.8 35 12 12 10 ½" 1(NT)

208 1 19.2 19.2 10.8 25 12 N/A 10 ½" 1(NT)
240 1 16.7 16.7 14.4 25 12 N/A 12 ½" 1(NT)

4

380 1 10.7 10.7 36.1 15 12 N/A 12 ½" 1(WT)
480 1 8.3 8.3 57.6 15 12 N/A 14 ½" 1(WT)
208 1 24.0 24.0 8.7 30 12 N/A 10 ½" 1(NT)
240 1 20.8 20.8 11.5 30 12 N/A 10 ½" 1(NT)

5

380 1 13.2 13.2 28.9 20 12 N/A 12 ½" 1(WT)
480 1 10.4 10.4 46.1 15 12 N/A 14 ½" 1(WT)
208 1 28.8 28.8 7.2 40 12 12 8 ½" 4
208 3 16.7 16.7 14.4 25 12 12 10 ½" 10(NT)
240 1 25.0 25.0 9.6 35 12 12 8 ½" 4

6

240 3 14.4 14.4 19.2 20 12 12 12 ½" 10(NT)
380 3 8.6 8.6 48.1 15 12 12 14 ½" 10(WT)
480 3 7.2 7.2 76.8 10 12 12 14 ½" 10(WT)
600 3 6.0 6.0 114.8 10 12 12 14 ½" 14
208 1 32.5 32.5 6.4 45 12 12 8 ½" 4
208 3 18.7 18.7 12.4 25 12 12 10 ½" 10(NT)
240 1 33.2 33.2 7.2 45 12 12 8 ½" 4

7

240 3 19.2 19.2 14.4 25 12 12 10 ½" 10(NT)
380 3 10.0 10.0 41.3 15 12 12 12 ½" 10(WT)
480 3 8.4 8.4 65.8 15 12 12 14 ½" 10(WT)
600 3 6.8 6.8 102.0 10 12 12 14 ½" 14
208 1 43.3 43.3 4.8 55 10 10 6 ¾" 4
208 3 25.0 25.0 9.6 35 10 10 8 ½" 10(NT)
240 1 37.5 37.5 6.4 50 10 10 8 ½" 4

9

240 3 21.7 21.7 12.8 30 10 10 10 ½" 10(NT)
380 3 14.3 14.3 32.1 20 12 12 12 ½" 10(WT)
480 3 10.8 10.8 51.2 15 12 12 14 ½" 10(WT)
600 3 9.1 9.1 76.5 15 12 12 14 ½" 14
208 1 48.8 48.8 4.3 65 8 10 6 ¾" 4
208 3 29.1 29.1 8.2 40 12 12 8 ½" 10(NT)
240 1 43.8 43.8 5.5 55 10 12 6 ¾" 4

10.5

13.5

240 3 25.3 25.3 11.0 35 12 12 8 ½" 10(NT)
380 3 17.1 17.1 27.5 25 12 12 10 ½" 10(WT)
480 3 12.6 12.6 43.9 20 12 12 12 ½" 10(WT)
600 3 10.2 10.2 68.1 15 12 12 14 ½" 14
208 1 57.7 57.7 3.6 75 8 10 4 1" 4
208 3 33.3 33.3 7.2 45 12 12 8 ½" 10(NT)
240 1 50.0 50.0 4.8 65 8 10 6 ¾" 4

12

240 3 28.9 28.9 9.6 40 12 12 8 ½" 10(NT)
380 3 18.6 18.6 24.1 25 12 12 10 ½" 10(WT)
480 3 14.4 14.4 38.4 20 12 12 12 ½" 10(WT)
600 3 11.3 11.3 61.2 15 12 12 14 ½" 14
208 1 64.9 64.9 3.2 85 8 10 4 1" 4
208 3 37.5 37.5 6.4 50 10 12 8 ½" 10(NT)
240 1 56.3 56.3 4.3 75 8 10 4 1" 4
240 3 32.5 32.5 8.5 45 12 12 8 ½" 10(NT)
380 3 21.4 21.4 21.4 30 12 12 10 ½" 10(WT)
480 3 16.2 16.2 34.1 25 12 12 12 ½" 10(WT)
600 3 12.0 12.0 57.7 20 12 12 12 ½" 14

Amp

Draw

Branch

Amp

Draw

Phase-

Phase

Resistance

(Ohms)

Min.
Feed

Breaker

or Fuse

Size

Internal

Power

Wire

Size

Element

Jumper

Wire

Size

Copper

Power Feed

Wire Size

Conduit

Size

Diagram

14

kW Volt Ph

15

18

24

27

30

36

39

J6 and J16 Wiring Chart (cont.)

Unit

Amp

Draw

208 1 72.1 72.1 2.9 95 6 8 3 1" 4 (DB)
208 3 41.6 41.6 5.8 55 10 12 6 ¾" 10(NT)
240 1 62.5 62.5 3.8 80 8 10 4 1" 4
240 3 36.1 36.1 7.7 50 10 12 8 ½" 10(NT)
380 3 22.9 22.9 19.3 30 12 12 8 ½" 10(WT)
480 3 18.0 18.0 30.7 25 12 12 10 ½" 10(WT)
600 3 16.0 16.0 43.3 20 12 12 12 ½" 14
208 1 86.5 86.5 2.4 110 6 8 2 1" 4 (DB)
208 3 50.0 50.0 4.8 65 8 10 6 ¾" 10(NT)
240 1 75.0 75.0 3.2 95 6 8 3 1" 4 (DB)
240 3 43.3 43.3 6.4 55 10 12 6 ¾" 10(NT)
380 3 27.9 27.9 16.0 35 12 12 8 ½" 10(WT)
480 3 21.7 21.7 25.6 30 12 12 10 ½" 10(WT)
600 3 18.1 18.1 38.3 25 12 12 12 ½" 14
208 1 115.4 38.5 1.8 145 10 12 1/0 1¼" 3A
208 3 66.6 66.6 3.6 85 8 10 4 1" 13(NT)
240 1 100.0 33.3 2.4 130 12 12 1 1¼" 3A
240 3 57.7 57.7 4.8 75 8 10 4 1" 13(NT)
380 3 37.1 37.1 12.0 50 10 12 6 ¾" 13(WT)
480 3 28.9 28.9 19.2 40 12 12 8 ½" 13(WT)
600 3 22.6 22.6 30.6 30 12 12 10 ½" 15
208 1 130.0 43.3 1.6 165 10 12 2/0 1½" 6A
208 3 74.9 37.5 3.2 95 10 12 3 1" 12(NCB)
240 1 112.5 37.5 2.1 145 10 12 1/0 1¼" 3A
240 3 65.0 65.0 4.3 85 8 10 4 1" 13(NT)
380 3 42.9 42.9 10.7 55 10 12 6 ¾" 13(WT)
480 3 32.5 32.5 17.1 45 12 12 8 ½" 13(WT)
600 3 24.0 24.0 28.8 30 12 12 8 ½" 15
208 1 144.2 48.1 1.4 185 8 10 3/0 1½" 6A
208 3 83.3 41.6 2.9 105 10 12 2 1" 12(NCB)
240 1 125.0 41.7 1.9 160 10 12 2/0 1½" 6A
240 3 72.2 36.1 3.8 95 10 12 3 1" 12(NCB)
380 3 45.7 45.7 9.6 60 10 12 4 1" 13(WT)
480 3 36.1 36.1 15.4 50 10 12 8 ½" 13(WT)
600 3 33.2 33.2 21.7 45 12 12 8 ½" 15
208 1 173.1 57.7 1.2 220 8 10 4/0 2" 6A
208 3 99.9 50.0 2.4 125 8 10 1 1¼" 12(NCB)
240 1 150.0 50.0 1.6 190 8 10 3/0 1½" 6A
240 3 86.6 43.3 3.2 110 10 12 2 1" 12(NCB)
380 3 55.7 55.7 8.0 70 8 10 3 1" 13(WT)
480 3 43.3 43.3 12.8 55 10 12 6 ¾" 13(WT)
600 3 36.2 36.2 19.1 50 10 12 8 ½" 15
208 1 187.5 62.5 1.1 235 8 10 250 2" 6A
208 3 108.3 54.1 2.2 140 8 10 1/0 1¼" 12(NCB)
240 1 162.5 54.2 1.5 205 8 10 4/0 1½" 6A
240 3 93.8 46.9 3.0 120 10 12 1 1" 12(NCB)
380 3 60.8 60.8 7.4 80 8 10 3 1" 13(WT)
480 3 46.9 46.9 11.8 60 8 10 6 ¾" 13(WT)
600 3 36.2 36.2 19.1 50 10 12 8 ¾" 15

Branch

Amp

Draw

Phase-

Phase

Resistance

(Ohms)

Min.
Feed

Breaker

or Fuse

Size

Internal

Power

Wire

Size

Element

Jumper

Wire

Size

Copper

Power Feed

Wire Size

Conduit

Size

Diagram

15

J6 and J16 Wiring Chart (cont.)

Unit

kW Volt Ph

208 1 196.8 65.6 1.1 250 8 10 250 2" 6A
208 3 113.8 56.9 2.1 145 8 10 1/0 1¼" 12(NCB)
240 1 168.8 56.3 1.4 215 8 10 250 1½" 6A

40.5

58.5

240 3 97.4 48.7 2.8 125 10 12 1 1" 12(NCB)
380 3 60.8 60.8 7.1 80 8 10 3 1" 13(WT)
480 3 48.7 48.7 11.4 65 8 10 4 ¾" 13(WT)
600 3 36.2 36.2 19.1 50 10 12 8 ¾" 15
208 3 119.1 59.5 1.9 150 8 10 2/0 1¼" 12(NCB)
240 1 187.5 62.5 1.3 235 8 10 250 2" 6A
240 3 108.3 54.1 2.6 140 8 10 1/0 1¼" 12(NCB)

45

380 3 68.6 34.3 6.4 90 12 12 2 1" 12(WT)
480 3 54.1 54.1 10.2 70 8 10 4 ¾" 13(WT)
600 3 42.2 42.2 16.4 55 10 12 6 ¾" 15
208 3 149.9 74.9 1.6 190 6 8 3/0 1½" 12
240 3 129.9 65.0 2.1 165 8 10 2/0 1½" 12

54

380 3 80.0 40.0 5.3 100 10 12 1 1" 12(WT)
480 3 65.0 65.0 8.5 85 8 10 4 1" 13(WT)
600 3 54.3 54.3 12.8 70 8 10 4 1" 15
208 3 159.9 79.9 1.5 200 6 8 4/0 1½" 12
240 3 140.7 70.4 2.0 180 6 8 2/0 1½" 12
380 3 91.4 45.7 4.9 115 10 12 1 1" 12(WT)
480 3 70.4 35.2 7.9 90 12 12 3 1" 12(WT)

600 3 54.3 54.3 12.3 70 8 10 4 1" 15
64 208 3 178.6 59.5 1.4 225 8 10 4/0 1½" 17
66 600 3 63.4 63.4 10.9 80 8 10 4 ¾" 18

240 3 162.4 54.1 1.7 205 8 10 4/0 1½" 17
68

380 3 102.8 34.3 4.2 130 12 12 1/0 1¼" 16(WT)

480 3 81.2 27.1 6.8 105 12 12 2 1" 16(WT)
79 380 3 120.0 40.0 3.7 150 10 12 2/0 1¼" 16(WT)

208 3 224.8 74.9 1.1 285 6 8 300 2" 17
81

240 3 194.9 65.0 1.4 245 8 10 250 2" 17

480 3 105.5 35.2 5.7 135 12 12 1 1" 16(WT)
85 600 3 81.5 81.5 8.5 105 6 8 2 1" 18
86 208 3 239.8 79.9 1.0 300 6 8 350 2" 17

240 3 211.1 70.4 1.3 265 6 8 300 2" 17
88

480 3 105.5 35.2 5.2 135 12 12 1/0 1¼" 16(WT)
90 380 3 137.1 45.7 3.2 175 10 12 2/0 1½" 16(CBWT)

Amp

Draw

Branch

Amp

Draw

Phase-

Phase

Resistance

(Ohms)

Min.
Feed

Breaker

or Fuse

Size

Internal

Power

Wire

Size

Element

Jumper

Wire

Size

Copper

Power Feed

Wire Size

Conduit

Size

Diagram

J6 and J16 Wiring Chart Notes:

1. Power feed wire sizing is based on using 75°C Cu THHN wire with feeder branch

protection rated at 125%.

2. Internal wire sizing is based on using 200°C SEW-2 or PTFE wiring in a raceway

with an ambient temperature up to 60°C.

3. For information on 277V, 415V, or 440V models reference the supplied drawing

or contact the factory.

4. Normal phase-to-phase resistance tolerance is ±5%.

5. 380, 480, and 600-volt phase-to-phase resistance values are shown with the transformer

disconnected.

6. For 575V models, multiply the kW rating of the 600V model by a de-rating factor of 0.92

to get the actual rating for 575V.

7. For models manufactured prior to June 24, 2005, that utilize wiring diagrams 3, 5, 6,

7(NT), 7(WT), or 11 please contact the factory for wiring diagrams.

16

J3 Wiring Chart

Unit

kW Volt Ph

2.9 120 1 23.8 5.0 30 12 12 10 ½" 4

5.7 120 1 47.5 2.5 60 10 12 6 ¾" 4
208 1 47.6 4.4 60 10 12 6 ¾" 4

9.9
208 3 27.5 8.7 35 12 12 8 ½" 10 (NT)

10.4

11.4

208 1 51.9 4.2 65 10 12 6 ¾" 4
208 3 28.8 8.3 40 12 12 8 ½" 10 (NT)
240 1 47.5 5.1 60 10 12 6 ¾" 4
240 3 27.4 10.1 35 12 12 8 ½" 10 (NT)
277 1 41.2 6.7 55 10 12 6 ¾" 4 (WT)
380 3 16.8 25.3 25 12 12 12 ½" 14
415 3 15.9 30.2 20 12 12 12 ½" 14
480 3 13.7 40.4 20 12 12 14 ½" 14
600 3 11.0 63.2 15 12 12 14 ½" 14

Amp

Draw

Phase-

Phase

Resistance

(Ohms)

Min.
Feed

Breaker

or Fuse

Size

Internal

Power

Wire

Size

Element

Jumper

Wire

Size

Copper

Power Feed

Wire Size

Conduit

Size

Diagram

J3 Wiring Chart Notes:

1. Power feed wire sizing is based on using

75°C Cu THHN wire with feeder branch

protection rated at 125%.

2.

Internal wire sizing is based on using 200°C SEW-2 or PTFE wiring in a raceway
with an ambient temperature up to 60°C.

3.

Normal phase-to-phase resistance tolerance is ±5%.

4. 277, 380,415, 480, and 600-volt phase-to-phase resistance values are shown with the
transformer disconnected.

J4 Wiring Chart

Min.
Feed

Breaker

or Fuse

Size

Internal

Power

Wire

Size

Element

Jumper

Wire

Size

Copper

Power Feed

Wire Size

Conduit

Size

Diagram

kW Volt Ph

11.3

12.6

13.8

208 1 54.1 3.8 70 8 8 4 1" 4
208 3 31.2 7.7 40 8 8 8 ½" 10 (NT)
220 1 57.3 3.8 75 8 8 4 1" 4
220 3 33.1 7.7 45 8 8 8 ½" 10 (NT)
230 1 59.8 3.8 75 8 8 4 1" 4
230 3 34.5 7.7 45 8 8 8 ½" 10 (NT)
240 1 62.5 3.8 80 8 8 4 1" 4

15

240 3 36.1 7.7 50 8 8 8 ½" 10 (NT)
480 3 18.0 30.7 25 12 12 10 ½" 10 (WT)
208 3 75.0 3.2 95 6 8 3 1" 10 (NT)

27

240 3 65.0 4.3 85 8 10 4 1" 10 (NT)
480 3 32.5 17.1 45 12 12 8 ½" 10 (WT)

Unit

Amp

Draw

Phase-

Phase

Resistance

(Ohms)

J4 Wiring Chart Notes:

1. Power feed wire sizing is based on using

75°C Cu THHN wire with feeder branch

protection rated at 125%.

2.

Internal wire sizing is based on using 200°C SEW-2 or PTFE wiring in a raceway
with an ambient temperature up to 60°C.

3.

Normal phase-to-phase resistance tolerance is ±5%.

4. 480-volt phase-to-phase resistance values are shown with the transformer disconnected.

17

Note: Wiring diagrams 3, 5, 6, 7 (NT), 7 (WT), and 11 are obsolete.

1(WT)

L1

Control, Low Water,

L2

& Hi-Limit Probe

Leak Detection Probe

1(NT)

L1 L2

Control

Module &

Display

J8

J2

J5

J3

J7

Control, Low Water,

& Hi-Limit Probe

Leak Detection

J8

Control

J2

J5

J7

Module &

J3

Display

Probe

10(WT)

L1 L3L2

Control, Low Water,

& Hi-Limit Probe

17

J5

J7

Leak Detection

Probe

10(NT)

L1 L3L2

Control

Module &

Display

J8

J2

J5
J7

J3

J8

Control

J2

Module &

J3

Display

L1 L2 L3

Control, Low Water,

& Hi-Limit Probe

Leak

Detection

Probe

18

Control, Low

Water, & Hi-Limit

Probe

Control

Module &

Display

J8
J4
J1

J5J3J2

J7

Leak

Detection

Probe

JX5

JX4JX

XB1

6

6A

L1 L2

Control

Module &

Display

J5

J7

J3

3A

J8

J2

L1 L2

J8

J2

J5

J7

Control

Module &

J3

Display

12 (WT)

12

Control, Low

Water, & Hi-Limit

Probe

L1 L2 L3

Control, Low Water,

& Hi-Limit Probe

Leak Detection Probe

L1 L2 L3

Leak

Detection

Probe

J5

J7

Control, Low Water,

& Hi-Limit Probe

Leak Detection

Probe

13 (NT)

L1 L3L2

J8

J2

Control

Module &

J3

Display

13(WT)

Control, Low Water,

& Hi-Limit Probe

Leak Detection Probe

J8

Control

J2

J5

Module &

J3

J7

Display

Control, Low Water,

& Hi-Limit Probe

J5
J7

Leak

Detection

Probe

Control

Module &

Display
J8

J2

J3

L1 L3L2

Control, Low Water,

& Hi-Limit Probe

J5
J7

Leak

Detection

Probe

J8

Control

J2

Module &

J3

Display

19

20

12 (NCB)

L1 L2 L3

Control, Low Water,

& Hi-Limit Probe

Leak Detection Probe

J5
J7

Control

Module &

Display
J8

J2

J3

15

L1 L3L2

Control, Low Water,

& Hi-Limit Probe

Leak Detection Probe

Control

Module &

Display

J8

J5

J7

J2

J3

14

L1 L3L2

Control, Low Water,

& Hi-Limit Probe

Leak Detection Probe

J8

J5
J7

J2

J3

21

Typical J6 Plumbing Connections

(Rear View)

Typical J16 Plumbing Connections

(Front View)

22

Typical J4 Plumbing Connections

(Rear View, shown with optional legs)

Typical J3 Plumbing Connections

(Front View, shown with optional legs)

23

SECTION III – SCHEDULED MAINTENANCE AND OPERATION

WARNING / CAUTION

Before perform

ing any maintenance procedure, make certain the power supply is turned OFF

and cannot accidentally be turned on.

MAINTENANCE AND OPERATION

The water heater is automatic in its operation. It will maintain a full tank of water at the
temperature setting of the controller. The water heater should not be turned on without first
making sure that the tank is full of water and that all air has been released.

FREEZING

The tank should be fully drained in the event the electricity has been turned off and if there
is danger of freezing.

CONTROLLER OPERATION

NOTE: All controller variables come preset from the factory to include a preset temperature
of 185°F.

1. To turn unit on or off:

a. Press the ON/OFF button on the display module.
b. Note that the controller will resume its last mode of operation if power is

disconnected.

2. To change setpoint temperature (the temperature is fully adjustable from 32° to 194°F
(0°-90°C):

a. Press the UP and DOWN arrows simultaneously to enter setpoint change mode.
b. Press the UP or DOWN button to change the setpoint temperature.
c. Pressing and holding the UP or DOWN button will scroll through the setpoint

temperature.

d. To leave setpoint change mode

i. Wait 5 seconds without pushing any buttons or press the UP and DOWN

buttons simultaneously.

3. To view the number of operational hours (the number of hours when a contactor is
pulled in) and software version:

a. Press the UP and DOWN arrows simultaneously to enter setpoint change mode.
b. Press the ON/OFF button.
c. Display will flash the software version (e.g. R14), HRS, followed by the hours

in thousands of hours, followed by the hours.

i. Example: r

14, H r S, l2 3, 4 5 6; indicates software version R1.4 and

123,456 hours.

d. To leave operational hours mode

i. Wait 5 seconds without pushing any buttons or press the UP and DOWN

buttons simultaneously.

4. Configuration Menu. (NOTE: Configuration menu change should only be made by
qualified personnel).

a.

Withe the controller turned OFF,

to enter the configuration menu, press and

hold the UP, DOWN, and ON/OFF buttons simultaneously for 5 seconds.
b. To scroll through menu settings, press the ON/OFF button.
c. To make a change to a menu setting use either the UP or DOWN arrow.
d. Settings:

i. Relays – sets the number of magnetic contactors used in the heater.

1. r ##, where ## is the number of magnetic contactors (01 or 02).

With XB1 installed ## can be 01 through 06.

24

ii. Low water detection – sets the low water detection on or off.

1. LOn, for low water on. (Factory Default)

2. LOF, for low water off.

iii. Low water reset – sets the low water reset for either automatic or manual

1. LAU, for low water automatic reset. (Factory Default)

2. LAn, for low water manual reset.

iv. Temperature units – sets the temperature units to either degrees

Fahrenheit or Celsius.

1. DEF, for degrees Fahrenheit. (Factory Default)

2. DEC, for degrees Celsius.

v. Differential – sets the number of degrees below setpoint that the heater

will resume heating after it has achieved setpoint.

1. d ##, where ## is the differential in degrees (1 to 20). (Factory set

at 02)

vi. Display – sets the display to either setpoint or actual temperature.

1. dSS, for display setpoint temperature. (Factory Default)

2. dSt, for display actual temperature.

vii. Heater Interlock – sets the heater interlock mode to on or off. (Only

available with r23 or later software).

1. HoF, to disable the 24-volt interlock feature. (Factory Default)

2. Hon, to enable the 24-volt interlock feature.

viii. XB1 Temperature Setpoint – sets the setpoint for the operation of the

XB1 relay operation.

e. To leave the configuration menu, wait 5 seconds without pushing any buttons or

press the UP and DOWN buttons simultaneously.

5. To reset any high-limit, no probe, or low water (when in manual reset mode) fault

condition, press the RESET button.

6. Display
a. By default the display will show the setpoint of the booster heater.
b. The decimal points on the display, as shown below, indicate that the controller

is calling for a contactor to pull in. If three or more contactors are installed, the
third decimal point is used for all remaining contactors.

ANNUAL INSPECTION

1. Monitor water temperature

a. Let water heater completely heat to a designated temperature setting.
b. After controller satisfies (that is, when the magnetic contactor actually clicks

off), draw water from as close as possible heater outlet and measure the
temperature.

c. Compare the water temperature of outlet water to the temperature setting of

the display when it satisfies. Normal variation between the two points is
approximately + 5°F.

25

d. If these two readings do not coincide within acceptable tolerances and

verification has been made of the accuracy of the temperature-reading gauge,
replace the control board and/or the sensor probe.

2. Lift test lever on relief valve and let water run through valve for a period of

approximately 10 seconds. This will help flush away any sediment that might build up
in water passageways.

3. Inspect element for leakage as follows:
a. Shut off power supply.
b. Remove front cover.
c. Visually inspect around heating element for evidence of leaks.
d. Rub around the heating element with a rag. Check for any evidence of

moisture. If moisture is present or a water drip is observed, follow procedure
outlined in Section V.
CAUTION: The area around the heating element may be hot.

4. Scale and mineral build-up on heating elements is a normal condition. It is

recommended that the heating element be removed for examination and if scaled,
should be cleaned. In an area of known hard or poor water conditions, the elements
may need to be checked more frequently. This will improve the efficiency of the
heater and increase the element life.
NOTE: Failure of the elements due to scale and mineral build-up is not covered under
warranty. See warranty for complete details.

a. Shut off power supply.
b. Drain the tank.
c. Remove front cover.
d. Disconnect the element wiring. It is recommended that one element at a time

is removed to simplify re-wiring.

e. Unscrew element.
f. Lime scale removal

i. Place limed ends of the heating element in a de-limer solution, designed

for potable water applications, and allow lime to dissolve. Do not allow
de-limer to contact heating element terminals.

g. Other scale removal

i. Silicates, sulfates, and alum inates must be removed by scraping or other

mechanical means. De-limers will not dissolve these types of scale.

h. Flush the cleaned ends of the elements with clean water.
i. Re-install element with new o-ring.
j. Re-attach element wires.
k. Continue until all heating elements are cleaned.
l. Fill the heater following the filling instructions provided in Section II and check

around the elements for leaks.

m. Re-apply power.

5. Check for loose electrical connections. Tighten as necessary.

SECTION IV – TROUBLESHOOTING

ERROR MESSAGES

1. Err, No, Prb
a. This message will flash when the controller does not detect that the probe is

connected to the control board. To clear this error reinsert the probe connector
and press RESET.

2. Err, too, hot, ### (where ### is the actual temperature of the water.)

26

a. This message will display if the temperature of the water exceeds the high limit

temperature setpoint. To clear this error, wait until the temperature is below the
operating setpoint and press RESET. Note that the unit will not reset until the
indicated temperature is below 195°F. If this message continually occurs, follow
the troubleshooting flow chart for continuous over-temperature condition.

3. Err, No, H2O
a. This message will display when the water level in the tank has dropped below

the sensor probe. To clear this message, refill the tank. If the low water reset is
set for automatic, the error will clear. If the low water reset is set for manual,
when the tank is full press RESET. Check the heater and the piping for leaks.
Check for mineral buildup on the probe and clean as required. Check for
continuity between the yellow wire and ground. See diagram 2 on the following
page.

4. Err, H2O, LEA
a. This message displays if the leak detection sensor determines there is water in

the base of the heater shell. To clear this message, remove the water from the
leak detection sensor. Check the unit and piping for leaks.

5. CC
a. This message displays if the display cable is installed into the control board

backwards. To clear this message, remove and correctly install the display cable.

6. 255
a. This message indicates that the probe is likely out of calibration. To clear this

message, it is recommended that the probe be removed and replaced.

7. HLd
a. This message indicates that the 24-volt interlock feature is enabled, there is no

24-volt signal present, and the heater is in standby mode. If it is not the intention
to operate the heater with the 24-volt interlock feature, this feature should be
disabled as shown in the controller operation section. (Only available with r23 or
later software).

CONTACTOR CARE

1. A chattering or humming from the contactor is due to dust or debris on the contact points

that prevents the contactor from making proper contact. The debris can be removed by
utilizing a can of antistatic cleaning and dusting spray (pressurized air) and spraying
through the side of the contactor to remove the debris.

DISPLAY BUTTONS

1. If the display randomly changes or does not respond when the buttons are pressed,

loosen the four (4) screws holding the display to the base, reseat the display in the
center of the opening, leaving the screws loose.

MISCELLANEOUS

2. If the display flashes when the unit is first turned on or turned on after maintenance,

check that the J5 terminal on the controller is engaging all four pins on the board.

3. Note that before replacing the control board, display, or probe, it is recommended that

the power supply to the booster heater be turned off at the main circuit breaker
disconnect to the booster heater to reset and clear the electronic controller.

CAUTION: Do not use plumber’s tape/Teflon tape/pipe dope when installing the probe.
Tape will prevent the low water detection system from operating properly and will cause
false low water errors. Lubricate O-ring prior to installation.

27

GENERAL TROUBLESHOOTING

Symptom Probable Cause Corrective Action

Water reaches setpoint
temperature but does

Low incoming water

temperature.
not last through the
entire dishwasher
cycle.

Incoming water

temperature is dropping.

Water pressure is too

high.

Booster heater may be

undersized.

Incorrect voltage. Voltage available at the booster heater must

If two magnetic

contactors are utilized,

one is not energizing.

One or more elements

are not energizing.

Water at the
dishwasher is not the

Gauge(s) not reading

correctly.
proper temperature.

Temperature setpoint

too low.

Booster heater piping to

the dishwasher is not

insulated.

Bypass valve is open or

allowing water to pass

when closed.

Incoming water temperature must be
adequate for the booster size. Increase the
incoming water temperature.
Primary water supply is not adequate to
continually provide correct temperature in
sufficient quantities. Increase the supply of
primary warm water.
Higher water pressure uses an excessive
supply of hot water. Verify a pressure
reducing valve is installed and adjust the
water pressure to 20 psi.
The booster heater must be properly sized
for the incoming water and rinse
requirements of the dishwasher. If required,
replace with a properly sized unit.

be correct for unit. Verify voltage on all
phases matches nameplate on the booster
heater.
Verify that both magnetic contactors are
operating. If not, see the ‘Magnetic
Contactor Troubleshooting’ section.
Verify that each element is drawing the
correct amperage. Replace elements as
required.
Check the temperature of the water with a
thermometer to verify the gauges are
working properly. Replace gauges, if
required.
Adjust the temperature setpoint.

If there is more than 5 linear feet of piping
between the booster heater and the
dishwasher the piping should be wrapped
in insulation or a recirculating system
should be installed.
Verify that the bypass valve between the
hot and warm water lines is closed. If
condition continues, replace the bypass
valve.

28

Symptom Probable Cause Corrective Action

Temperature and
pressure relief valve
seeps

No pressure reducing

valve or wrong valve

installed causing

The proper pressure reducing valve with high
pressure bypass must be installed in the inlet

water line to allow for the expansion of water.
excessive pressure in
the unit.
Pressure reducing valve
bypass is blocked.
Anti-siphon valve or
check valve installed in
the warm water inlet

Clean the bypass or install a new valve with a

built-in bypass.

Remove the anti-siphon valve or the check

valve to allow for the expansion of the water

or install a back pressure relief valve.
line.

Temperature and
pressure relief valve
opens and/or high
limit temperature
error occurs.

Unit is overheating due
to improper P65 probe
calibration.
Unit is overheating due
to the magnetic

See the ‘P65 Probe Troubleshooting’ section.

See the ‘Magnetic Contactor Troubleshooting’

section.
contactor staying in the
closed position.

Booster heater does
not heat at all.

Main supply circuit
breaker tripped.
Booster heater circuit
breaker tripped.

Check and/or reset the circuit breaker.

If unit is supplied with a circuit breaker, check

and/or reset the circuit breaker.
Booster in high limit. If a high limit error occurs, allow water to cool

and press the reset button. If error continues

see symptom “Temperature and pressure relief

valve opens and/or high limit temperature

error occurs”.
Low water error. Verify that booster heater is full of water. If

error is still present see the ‘P65 Probe

Troubleshooting’ section.
Magnetic contactor
does not energize.
No power to control
board (T1000) or
display (TD1000) not
lit.

See the ‘Magnetic Contactor Troubleshooting’

section.

Reseat the display (TD1000) ribbon cable in

the control board (T1000) connector. If the

display is still not lit, see the ‘Control Board

(T1000) / Display (TD1000) Troubleshooting’

section.
Element Failure Disconnect the wires from each element and

verify that the resistance (ohms) value for each

element is correct. Replace elements as

required.
Incorrect Configuration
Settings

Verify and correct configuration settings as

required.

29

CONTROL BOARD (T1000) / DISPLAY (TD1000) TROUBLESHOOTING

1. Verify proper power supply voltage between each phase (L1 to L2, L2 to L3, and L1 to

L3). The power supply voltage should match the voltage listed on the booster nameplate.
If voltage is incorrect, check main supply wiring or replace unit with proper booster
heater.

2. Check for 208/240VAC between pin 1 (white wire) and pin 2 (black wire) of the J5

connector on the T1000 control board. If no voltage is present, skip to step 4.

3. If 240VAC is present, check for 24VDC between D1 and ground. If 24VDC is present

replace the display (TD1000). If 24VDC is not present replace the control board (T1000).

Probe Ground (J7) Display Cable Leak Detection Wire (J2)

Expansion (J1)

Ground Wire (J8)

(D1)

Probe Cable
(J3)

Alarm Relay
(J4)

Power Wire (Common, White) Connector (J5)

Power Wire (Black) Wire to #1 Contactor (yellow)

Wire to #2 Contactor (red)

4. If a transformer is installed, verify proper power supply voltage to the primary side of the

transformer and verify approximately 240VAC on the secondary side of the transformer.
If voltage is present of the primary side but not on the secondary side, replace the
transformer.

5. If circuit breakers are installed, verify that the circuit breaker is ON. Verify proper power

supply voltage between each phase (L1 to L2, L2 to L3, and L1 to L3) to the line side of
each circuit breaker and to the load side of each circuit breaker. If voltage is present of
the line side but not on the load side, replace the circuit breaker.

6. Verify that the booster heater is wired according to the proper wiring schematic for the

unit. Correct as required. If unit still does not operate, contact the factory.

MAGNETIC CONTACTOR TROUBLESHOOTING

1. With the unit ON and calling for heat, check for lit decimal points on the display. If the

unit has a single contactor, the first decimal to the right of the display should be lit. If two
decimals are lit, verify that the configuration is set for one contactor. If the unit has two
contactors, verify that two decimals are lit. If only one decimal is lit, verify that the
configuration is set for two contactors. If no decimals are lit, continue to the ‘P65 Probe
Troubleshooting’ section.

2. With the unit ON and calling for heat and one decimal lit, check for 240VAC between

pin 1 (white wire) and pin 4 (yellow wire) of the J5 connector on the T1000 control
board. If no voltage is present, replace the control board (T1000). If voltage is present,
check for voltage across the contactor coil. If voltage is present at the contactor coil,
replace the magnetic contactor. If no voltage is present, verify that the booster heater is
wired according to the proper wiring schematic for the unit.

30

3. If the unit has two contactors, with the unit ON and calling for heat and two decimals lit,

check for 240VAC between pin 1 (white wire) and pin 3 (red wire) of the J5 connector
on the T1000 control board. If no voltage is present, replace the control board (T1000). If
voltage is present, check for voltage across the contactor coil. If voltage is present at the
contactor coil, replace the magnetic contactor. If no voltage is present, verify that the
booster heater is wired according to the proper wiring schematic for the unit.

P65 PROBE TROUBLESHOOTING

1. Unplug and reseat the P65 probe wire in the jack on the T1000 control board. Note that

the error message “ Err, No, Prb” will be displayed and the reset button must be
pressed to clear the message.

2. If problem persists, unplug the P65 probe from the control board and plug into the RJ45

pigtail (not supplied).

3. If the problem is with temperature control or high limit:
a. Change the configuration to ‘dSt’ to display the actual water temperature.
b. Check the temperature of the water with a thermometer and compare that with the

temperature on the display. If the two temperatures coincide, replace the T1000
control board. If the two temperatures do not coincide, continue to the next step.

c. Unplug the P65 probe from the control board and plug into the RJ45 pigtail (not

supplied). Check the resistance value (ohms) between the blue wire of the pigtail
(#1) and the red wire of the pigtail (#4). Compare the resistance value measure
with the chart below at the measured temperature of the water. If the two values
coincide, replace the T1000 control board. If the two values do not coincide,
replace the P65 sensor

4. If the problem is with low water:
a. Verify that the unit is filled with water.
b. Check for continuity between the yellow wire of the pigtail (#2) and ground. If

continuity exists, replace the T1000 control board. If no continuity exists, replace
the P65 sensor probe.

Thermistor Resistance vs. Temperature

Water Temperature Resistance (±3%)

70°F
80°F

90°F
100°F
110°F
120°F
130°F
140°F
150°F
160°F
170°F
180°F
190°F

11883Ω

9299Ω
7334Ω
5828Ω
4664Ω
3758Ω
3048Ω
2488Ω
2043Ω
1687Ω
1400Ω
1169Ω

980Ω

31

SECTION V – SERVICING AND REPLACEMENT OF PARTS

WARNING / CAUTION

Before servicing or replacing any part, make sure to turn the power supply to the unit OFF.

HEATING ELEMENT

1. Disconnect power from unit.

2. Shut off incoming water supply.

3. Attach hose to drain connection.

4. Lift manual release lever on relief valve to let air into system or break union on

outgoing water line.

5. Drain water from tank.

6. Disconnect the wires from the heating element terminals.

7. Unscrew element with a 1-7/8” 6-point socket with no bevel.

O-Ring Groove O-Ring Terminal Connections #220 Buna-N O-Ring

8. Install new #220 Buna-N o-ring gasket and install new heating element. NOTE:

Hubbell recommends lubricating the o-ring with Parker O-Lube prior to installation.

9. Rewire element according to the wiring diagram as shown in the Section II.

10. Fill tank and check around element for any leaks.

MAGNETIC CONTACTOR

1. Disconnect power from unit.

2. Disconnect line and load wires to contactor.

3. Disconnect the control circuit wires.

Control Wires

Line Wires

Load Wires

Mounting Screws

4. Loosen holding screws and remove contactor.

5. Replace with new contactor using reverse procedure.

CONTROL BOARD

1. Disconnect power from unit.

2. Disconnect display cable, probe cable (J3) and probe ground (J7), leak detection wire

(J2), ground wire (J8), and terminal block (J5) from the control board. NOTE: The
terminal block (J5) is removable by grasping the terminal block on the ends and

32

pulling straight away from the board.

Probe Ground (J7) Display Cable Leak Detection Wire (J2)

Expansion (J1)

Ground Wire (J8)

(D1)

Probe Cable
(J3)

Alarm Relay
(J4)

Power Wire (Common, White) Connector (J5)
Power Wire (Black) Wire to #1 Contactor (yellow)
Wire to #2 Contactor (red)

Note: Probe connector J3 comes filles with a dielectric gel that should remain in the
connector.

3. Remove four (4) screws securing control board to panel.

4. Remove and replace control board.

5. Reconnect wires disconnected in step 2. NOTE: When reconnecting the ribbon cable,

be sure to have the key on the cable align with the slot in the connector.

6. Connect power to unit.

RELIEF VALVE

1. Disconnect power from unit.

2. Shut off incoming water supply.

3. Attach hose to drain connection.

4. Lift manual release lever on relief valve to let air into system or break union on

outgoing water line.

5. Drain water from tank.

6. Disconnect overflow piping.

7. Unscrew relief valve, remove assembly and replace with new one.

8. Connect overflow piping.

9. Turn on incoming water supply and check for leaks.

10. Connect power to unit.

P65 SENSOR PROBE

1. Disconnect power from the unit.

2. Unplug the P65 probe connector from J3 and the probe ground from J7 on the T1000

control board.

Probe Ground (J7)

Probe
Connection
(J3)

33

3. Twist the cord and shrink-wrap end of the P65 probe (or cut the shrink-wrap with a sharp

knife) to loosen the P65 sensor assembly from the P65 thermowell.

4. Remove the old P65 sensor assembly by pulling on the cord coming out of the P65

thermowell.

Note: It is unnecessary to unscrew the

thermowell from the vessel to replace the P65 sensor.

Cord P65 Sensor

Shrink-Wrap Cap

5. Insert the new P65 sensor assembly into the P65 thermowell. Be sure to insert the sensor

until the shrink-wrap cap engages the threads on the end of the thermowell.

Note: The new sensor and cord assembly is push-fit onto the end of the thermowell

threads. Do not twist the new sensor and cord assembly into the thermowell. The thermal
conductive heat transfer paste inside the thermowell is sufficient for replacement sensors.
Adding additional paste is not required.

6. Plug P65 probe connector into the T1000 control board.

7. Turn on power to the unit. If display shows “ E rr, N o , P r b ”, press the reset button.

P65 THERMOWELL

1. Follow steps 1-4 for removing the P65 Sensor Probe above.

2. Shut off incoming water supply.

3. Attach hose to drain connection.

4. Lift manual release lever on relief valve to let air into system or break union on outgoing

water line.

5. Drain water from tank.

6. Remove the thermowell from tank using a 13/16” socket.

7. Install new #115 Buna-N o-ring gasket and

install new thermowell. NOTE: Hubbell
recommends lubricating the o-ring with
Parker O-Lube prior to installation.
WARNING: Do not remove the jam nut.

Thermowell

8. Reinstall or install a replacement P65

sensor probe in accordance with steps 5 and 6
above.

9. Refill tank.

10. Check for leaks. Retighten as required.

11. Turn on power to the unit.

12. Note that to resume operation the controller will

need to be reset by pressing the ‘RESET’ button on the display.

CAUTION: Do not use plumber’s tape/Teflon tape/pipe dope when installing the P65
Thermowell. Tape will prevent the low water detection system from operating properly and
will cause false low water errors. Lubricate O-ring prior to installation.
Tighten probe at the brass hex flats only.

34

SECTION VI – SERVICE PARTS LIST

Category Description Volts Ohms Hubbell P/N

Accessories Bronze Pressure Reducing Valve N45BU

Plastic Legs (Price each, 4 Req'd.) 61649NOBN5T4
Nickel Plated Legs (Price each, 4 Req'd.) AE61-4002-C
Stainless steel adjustable legs (Price each) A50-5048-C
Floor Mount Legs S/S (Price each, 4 Req'd.) A50-9939-C
Temp. and Pressure Gauge T405
Dielectirc Union, 3/4" DIELECTRIC UNION
Relief Valve (up to 58 kw) 100XL .75 150LB
Relief Valve (64-90 kw) 40XL-4 1 150LB
Slide Brackets (J6 models only, 2 per set) J6 SLIDE BRACKET
J6, 3 Element Plastic Protective Shroud (1 to 18 kW) J6-3 SHROUD
J6, 6 Element Plastic Protective Shroud (24 to 58.5 kW) J6-6 SHROUD
J16 Element Plastic Protectiv e Sh r ou d J16 SHROUD
Water Treatment System (blended phosphate) HBW-CLEAR
Replacement cartridge for water treatment RSC-10

Circuit Breakers 60 amp CB 60 AMP

70 amp CB 70 AMP
80 amp CB 80 AMP
90 amp CB 90 AMP
100 amp CB 100 AMP

Contactors 20 Amp Resistive, 15 Amp Inductive, 208/240 VAC Coil C25DNF315B

40 Amp Resistive, 30 Amp Inductive, 208/240 VAC Coil C25DNF330B
50 Amp Resistive, 40 Amp Inductive, 208/240 VAC Coil C25DNF340B
65 Amp Resistive, 50 Amp Inductive, 208/240 VAC Coil C25DNF350B
75 Amp Resistive, 60 Amp Inductive, 208/240 VAC Coil C25FNF360B
90 Amp Resistive, 75 Amp Inductive, 208/240 VAC Coil C25FNF375B

Elements
J4, J6, and J16
(Note: Each element
is supplied with an
O-Ring)

Elements 1900 Watts 120 7.6 C1315-39
J3 3300 Watts 208 13.1 C1315-40
(Note: Each element 3460 Watts 208 17.6 C1315-36
is supplied with an 3800 Watts 240 15.2 C1315-37
O-Ring) 3800 Watts 277 20.2 C1315-38

2000 Watts 208 21.6 C1315-2
4000 Watts 208 10.8 C1315-3
5000 Watts 208 8.7 C1315-4
6000 Watts 208 7.2 C1315-5
6500 Watts 208 6.7 C2315-6
7150 Watts 208 6.1 C2315-7
9000 Watts 208 4.8 N2375-9
9600 Watts 208 4.5 N2375-10
2000 Watts 240 28.8 C1315-11
3000 Watts 240 19.2 C1315-12
3500 Watts 240 16.5 C1315-13
4000 Watts 240 14.4 C1315-14
4500 Watts 240 12.8 C1315-15
5000 Watts 240 11.5 C1315-16
6000 Watts 240 9.6 C1315-17
6500 Watts 240 8.9 C1315-18
6750 Watts 240 8.5 C1315-34
7500 Watts 240 7.7 C2315-19
9000 Watts 240 6.4 N2375-20
9750 Watts 240 5.9 N2375-21
2000 Watts 480 115.2 C1315-22
2333 Watts 480 98.8 C1315-23
3000 Watts 480 76.8 C1315-24
3500 Watts 480 65.8 C1315-25
4000 Watts 480 57.6 C1315-26
4500 Watts 480 51.2 C1315-27
5000 Watts 480 46.1 C1315-28
6000 Watts 480 38.4 C1315-29
6500 Watts 480 35.4 C1315-30
7500 Watts 480 30.7 C1315-31
9000 Watts 480 25.6 N2375-32
9750 Watts 480 23.6 N2375-33
6750 Watts 480 34.1 C1315-35
Extra O Ring (#220 Buna-N) O RING J MODEL

3800 Watts 346 31.5 C1315-41

35

SERVICE PARTS LIST (cont.)

r

k

r

K

K

(

K

)

K

K

K

K

K

p

r

p

r

p

p

r

p

Category Description Volts Ohms Hubbell P/N

Misc. Electrical

Vessel J6 Vessel with 3 Element OpeningsJ6-3 TAN

includes insualtion J6 Vessel with 6 Element OpeningsJ6-3 TAN

and o-rings

Stainless Steel J6, 3 Element Base J6-3 BASE
Enclosure Parts J6, 3 Element To

Control Board T1000
Digital Display Module (with overlay and J16 Extension) TD1000
J16 Ribbon Cable Extension RIBBON CABLE J16
Display Overlay OVERLAY J MODEL
Probe Senso
Probe Thermowell (includes #115 Buna-N O-Ring) P65 WELL
Transformer 480-208V, 50VA B050-3299-3
Transformer 600-195V, 50VA B050-3350-3
Transformer 380-185V, 50VA B050-3351-3
Transformer 480-240V, 100VA B100PU1519JJ
Transformer 600-195V, 100VA B100-3350-3
Transformer 380-220V, 100VA B100RFD34XJ
Transformer 480-208V (J3 and J4 only) TRAN 480-208 25VA
Transformer 380-208V (J3 only) TRAN 380-208 25VA
Transformer 277-208V (J3 only) TRAN 277-208 25VA
Transformer 600-208V (J3 only) TRAN 600-208 25VA
Power Distribution Block 175 amp 2 pole 16220-2
Power Distribution Block 175 amp 3 pole 16220-3
Power Distribution Block 310 amp 3 pole 16023-3
Diffuser Assembly with Nipple J6 DIFFUSER
RJ45 Pigtail for P65 Probe Testing P65-RJ45 TESTER
Low Temperature Interloc
24-Volt Interlock Adapte
Remote Alarm Plug Adapter PLUG ADAPTER J4
Wire #18 200C (black,white,red,yellow) Tefzel 750 WIRE #18 200C "COLOR"
Wire #12 200C (blue or red) Tefzel 750 WIRE #12 200C "COLOR"
Wire #10 200C (blue or red) Tefzel 750 WIRE #10 200C "COLOR"
Wire #8 200C (blue or red) Tefzel 750 WIRE #8 200C "COLOR"
Wire #6 200C (black) Tefzel 750 WIRE #6 200C BLAC

J16 Vessel with 3 Element OpeningsJ16-3 TAN
J16 Vessel with 6 Element OpeningsJ16-6 TAN
J16 Vessel with 9 Element OpeningsJ16-9 TAN
J3 Vessel J3 TAN
J4 Vessel J411R TAN

Enclosure J6-3 JACKET
J6, 3 Element Front Cove
J6, 6 Element Base J6-6 BASE
J6, 6 Element To
J6, 6 Element Front Cove
J16 Base J16 BASE
J16 To

Enclosure J16 JACKET
J16 Front Cover J16 FRONT COVER
J3 Base J3 BASE

Enclosure J3 JACKET

J3 To
J3 Front Cove
J4 Base J4 BASE
J4 To

Enclosure J4 JACKET

J4 Front Cover J4 FRONT COVER

Enclosure J6-6 JACKET

P65

XB1
PLUG ADAPTER J1

J6-3 FRONT COVER

J6-6 FRONT COVER

J3 FRONT COVER

36

SECTION VII – TORQUE VALUES

Part P/N Wire Size

Element to

Tank

Wire to

Element

Probe to Tank All N/A 300 25

Wire to Ground

Lug

Wire to Circuit

Breaker

Transformer All All 15 1.25

Wire to Control

Board

C25DNF315B
C25DNF330B

Wire to

Contactor

Wire to Power

Distribution

Block

Control Board

to Panel

Display to Base All N/A 10 0.83

All Other

Components to

Panel

C25DNF340B
C25DNF350B

C25FNF360B
C25FNF375B

All N/A 600 50

All All 15 1.25

KA8C All 25 2.08
KA4C All 45 3.75

#14-#10 35 2.92

All

All All 3.5 0.29

Line All 275 22.92

16023-3
16023-2

63133
63132

All N/A 10 0.83

All N/A 20 1.67

Load

Line

Load

#8 40 3.33

#6-#4 45 3.75

#14-#12 15 1.25

#10 25 2.08

#8 40 3.33

#6-#4 45 3.75

#14-#10 40 3.33

#8 45 3.75

#6-#4 50 4.17

#14-

#10

#8 25 2.08

#6-#4 35 2.92

#14-#8 50 4.17

#6-2/0 120 10

#14-

#10

#8 25 2.08

#6-#4 35 2.92

Torque
(in•lbs)

20 1.67

20 1.67

Torque

(ft•lbs)

37

SECTION VIII – WARRANTY INFORMATION

LIMITED WARRANTY

1. PRODUCT WARRANTY. Hubbell warrants the booster heater it manufactures and its

components (the "Product") to be free from defects in materials and workmanship, under
normal use and service for the period of time identified below beginning from the date of
installation, provided that the product is installed within three (3) months of date of shipment
from Hubbell and when the Product is installed and maintained in accordance with Hubbell's
written instructions (see operators manual for details). Owner must establish the Product's
purchase date by means satisfactory to Hubbell in its sole discretion.

TANK and COMPONENTS: One (1) year parts and labor
TANK ONLY: Ten (10) years Non Pro-Rated
REPLACEMENT PARTS: Thirty (30) days parts only, no labor, from date of purchase

SUCH WARRANTIES DO NOT COVER:

• Product failure (including but not limited to the tank and/or heating elements) caused

by liming, sediment buildup, chemical corrosion, chlorine corrosion, or freezing.

• Temperature or other controller setting adjustments, pressure reducing valve

adjustments, resets, and plumbing leaks.

• Product misuse, tampering or misapplication, accidental damage, improper installation

or the application of improper voltage.

• Costs incurred for shipping, delivery, handling, and/or administrative charges.

• For the tank warranty after the first year, all labor, shipping, installation costs, and

components (other than the tank) are the responsibility of the owner.

• With respect to labor warranty within the first year, overtime, holiday, weekend or any

other non-standard labor rate.

• Excessive and unreasonable labor rates and/or travel expenses as determined by

Hubbell in its sole discretion.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OR PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT
INFRINGEMENT.

2. LIMITATION OF REMEDIES AND DAMAGES. Hubbell's liability and Buyer's

exclusive remedy hereunder will be limited solely, at Hubbell's option, to repair or
replacement by a Hubbell authorized service agency (other than where Buyer is located
outside of the United States or Canada, in which case Hubbell's liability and Buyer's
exclusive remedy hereunder will be limited solely to replacement of part under warranty)
with respect to any claim made within the applicable warranty period referred to above.
Without limiting the generality of the foregoing, all warranty items shall be returned by
Buyer, at its sole expense, to the nearest Hubbell-authorized service agency or to the Hubbell
factory (45 Seymour Street Stratford, CT 06615) for replacement or repair. Hubbell reserves
the right to accept or reject any such claim in whole or in part. Hubbell will not accept the
return of any product without prior written approval from Hubbell, and all such approved
returns shall be made at Buyer's sole expense. HUBBELL WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS
RESULTING FROM THE USE OR INABILITY TO USE THE PRODUCTS OR FROM
THE USE OF OR INABILITY TO USE THE PRODUCTS OR FROM THE PRODUCTS
BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER
PRODUCT OR GOODS.

38

NOTES

39

P.O. BOX 288

STRATFORD, CT 06615-0288

PHONE: [phone]

FAX: [phone]

INTERNET: http://www.hubbellheaters.com/

40