Page 1
INSTALLATION INSTRUCTIONS
FIGURE 5
FIGURA 5
FIGURE 6
FIGURA 6
PAGE 2
WIRE BOX COVER
#8-32 SCREWS
HOOKLOOP
POWER CORD
CLOSURE BRACKET
LOCKNUT
YOKE
LOCKNUT
INSTALLING PENDANT MOUNT (See Figure 7):
1. Remove wire box cover by removing (2) 8-32 screws. (Figure 5)
2. Thread one Locknut onto the Rigid Conduit at least ½”.
3. Thread a second Locknut onto the end of the Rigid Conduit allowing enough gap
to slide the yoke between the two Locknuts.
4. Lift Fixture and slide the Conduit into the “U” channel of the Yoke. The Yoke will
be sandwiched between the two Locknuts.
5. Feed approximately 3-4” of Supply Cord into the wire box with the supply wires
hanging out of the Wire Box.
6. Crimp Strain Relief on Power Cord just behind the bottom of the Rigid Conduit.
7. Tighten bottom Locknut to Lock the Yoke in place.
8. Connect Supply wires to the Fixture wires with approved Wirenuts.
9. Place Wires inside Housing and replace wire box cover. Tighten Screws.
PENDANT
3/4" RIGID CONDUIT
UTB UTILIBAY
LED HIGHBAY
™
LOCKNUT
STRAIN RELIEF
Figure 7
F
FIGURA 7
IGURE 7
LOCKNUT
YOKE
WARNINGS
Observe all precautions usually followed when dealing with high
voltage equipment when installing or servicing this light fixture.
• Disconnect power before installing or servicing.
• The product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
• Protect all wiring connections with approved insulators rated 600V. 150ºC.
• Line voltage must match fixture voltage requirement.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
• Upon receipt of this fixture, thoroughly inspect it for any damage.
If any is found, the carrier should be notified and held accountable.
HIL_0170_UTB_INST_16
Page 2
FIGURE 5
FIGURA 5
PAGE 2
WIRE BOX COVER
#8-32 SCREWS
FIGURE 1
FIGURA 1
F
IGURE 2
FIGURA 2
PAGE 1
YOKE ASSEMBLY
HOUSING
1/4-20 SCREW
8-32 SCREW
STAR LOCK
WASHER
YOKE
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
YOKE ASSEMBLY
FIGURE 1
FIGURA 1
PAGE 1
YOKE ASSEMBLY
HOUSING
FIGURE 1
FIGURA 1
F
IGURE 2
FIGURA 2
UTILIBAY (UTB) INSTALLATION INSTRUCTIONS
WARNINGS:
Observe all precautions usually followed when dealing with high
voltage equipment when installing or servicing this light fixture.
Disconnect power before installing or servicing.
The product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
Protect all wiring connections with approved insulators rated 600V.
150
O
C.
Line voltage must be 120V – 277V to match Fixture voltage
requirement.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Upon receipt of this Fixture, thoroughly inspect it for any damage.
If any is found, the carrier should be notified and held accountable.
ATTACH YOKE ASSEMBLY TO HOUSING:
1. Align holes in Yoke to holes on side of Housing (2 places). (See
Figure 1)
2. Secure Yoke to Housing with (2) ¼-20 screws & (2) Star washers.
(See Figure 2)
3. Prevent rotation of the Yoke with (2) 8-32 screws. (See Figure 2)
4. Connect both halves of Driver Disconnect. (See Figure 3)
5. Attach Electrical Box Cover to Housing with (2) 8-32 screws. (See
Figure 4)
PAGE 1
YOKE ASSEMBLY
HOUSING
SEE WARNING ON CARTON
ELECTRICAL
BOX COVER
#8-32 SCREWS
1/4-20 SCREW
8-32 SCREW
STAR LOCK
WASHER
YOKE
ATTACH YOKE ASSEMBLY TO HOUSING:
1. Align holes in Yoke to holes on side of Housing (2 places). (See Figure 1)
2. Secure Yoke to Housing with (2) ¼-20 screws and (2) star washers. (See Figure 2)
3. Prevent rotation of the Yoke with(2) 8-32 screws. (See Figure 2)
4. Connect both halves of Driver Disconnect. (See Figure 3)
5. Attach Electric Box Cover to Housing with (2) 8-32 screws. (See Figure 4)
PAGE 1
Figure 1
DRIVER DISCONNECT
HOUSING
#8-32 SCREWS
IGURE 2
F
Figure 2
STAR LOCK
WASHER
ELECTRICAL
BOX COVER
YOKE
8-32 SCREW
1/4-20 SCREW
INSTALLING HOOK MOUNT (See Figures 5 & 6):
1. Remove wire box cover by removing (2) 8-32 screws. (Figure 5)
2. Insert end of Cord through Hook. Supply Cord is to be rated for a
minimum of 90°C 16/3 SOW-A.
3. Feed approximately 3-4” of Supply Cord through hook.
4. Crimp Strain Relief on Power Cord just behind Hook.
5. Thread the ¾” Locknut onto the Hook almost to the flange of the hook.
Hex shape on the hook should be on the casting in order to tighten it in place.
6. CAUTION: Do not twist the Hook by using a screwdriver blade – too
much force could break the Hook.
7. Place the Hook in the “U” channel of the yoke.
8. Thread a second Locknut onto the Hook and tighten to keep hook
from loosening.
9. The yoke will be sandwiched by the two Locknuts.
10. Connect Cord wires to the Fixture wires with approved Wirenuts.
11. Place Wires inside Wire Box and replace wire box cover. Tighten
Screws that secure wire box cover.
12. Attach Hook Closure Bracket onto end of Hook with Screw provided.
After Fixture is hung, the Closure Bracket should be secured across
the hook opening to prevent disengagement.
#8-32 SCREWS
WIRE BOX COVER
Figure 3
FIGURE 3
FIGURA 3
Figure 4
Figure 5
renuts.
Tighten
provided.
ed across
STRAIN RELIEF
HOOKLOOP
LOCKNUT
F
IGURE 6
FIGURA 6
Figure 6
POWER CORD
CLOSURE BRACKET
LOCKNUT
YOKE
Loading...