Hubbell PS0389NGY Reference Drawing

SHELTON, CT

HUBBELL INCORPORATED

WIRING DEVICE-KELLEMS

~ANGLE TOL. ±2

.XXX= ± .005

.XX = ± .01

OTHERWISE SPECIFIED

TOLERANCES UNLESS

CAGE CODE 74545

4

4

FFS

MALLEN

SWIVELLOK FITTING

LIQUID-TIGHT NON- METALLIC

9/21/16

NONE

M-13462

M-13462

B

DIMENSION SHEET FOR CAT. NO.

TITLE

DIMENSIONS ARE IN INCHES [mm].

SUBJECT TO CHANGE WITHOUT NOTICE.

PRODUCT SHOWN ON THIS DRAWING ARE

THE DESIGN AND DIMENSIONS OF THE

CHK. BY

DR. BY

DATE

SCALE

BLACK/GRAY

NYLON

NUT

COMPRESSION

BLACKNYLON

FERRULE

NATURAL/BLACK

NYLONLOCK NUT

BLACK

ELASTOMERO-RING

BLACK/GRAY

NYLONCONNECTOR

FINISHMATERIALDESCRIPTION

LIST OF PARTS

DATEAPPDESCRIPTIONREV

9/21/16

FFS

22362 MYA

NEW RELEASE PER DCN

1

(49.3)

1.94

(58.4)

2.30

(46.7)

1.84

(24.4)

0.96

(18.3)

0.72

(101.6)

4.00

(45.7)

1.80

1 (27)1 (27)

PS1009NGY

PS1009NBK

(41.9)

1.65

(56.6)

2.23

(40.4)

1.59

(18.8)

0.74

(14.7)

0.58

(93.0)

3.66

(38.9)

1.53

3/4 (21)3/4 (21)

PS0759NGY

PS0759NBK

(35.8)

1.41

(50.8)

2.00

(36.3)

1.43

(14.0)

0.55

(14.5)

0.57

(83.1)

3.27

(33.0)

1.30

1/2 (16) 1/2 (16)

PS0509NGY

PS0509NBK

(35.8)

1.41

(50.8)

2.00

(36.3)

1.43

(14.0)

0.55

(14.5)

0.57

(83.1)

3.27

(33.0)

1.30

3/8 (12)1/2 (16)

PS0389NGY

PS0389NBK

(mm)

INCH

- G -

(mm)

INCH

- F -

A/C*

(mm)

INCH

- E -

(mm)

INCH

- D -

(mm)

INCH

- C -

(mm)

INCH

- B -

(mm)

INCH

- A -

TOR)

DESIGNA-

(METRIC

SIZE

TRADE

CONDUIT

TOR)

DESIGNA-

(METRIC

SIZE

THREAD

NPT

GRAY

CAT NO.

BLACK

CAT NO.

7. TOLERANCES: XX±.02, XXX±.005, ANGLES ±1°. GENERAL TOLERANCES DO NOT APPLY.

REFERENCE ONLY.

6. PRIMARY DIMENSIONS ARE INCHES. UNITS IN SI ARE PROVIDED AS

5. AGENCY APPROVALS - UL LISTED AND CSA CERTIFIED.

OF CERTAIN HAZARDOUS SUBSTANCE IN ELECTRICAL OR ELECTRONIC EQUIPMENT.

4. RoHS COMPLIANCE: CONNECTORS MEET EU DIRECTIVE, RESTRICTION OF THE USE

3. COLORS: SEE TABLE

2. TEMPERATURE RANGE: -30°F (-34°C) TO 225°F (107°C).

1. MATERIAL: 6/6 NYLON

NOTES:

-.000

Ø I +.010

FOR NON THREADED MOUNTING

SUGGESTED CLEARANCE HOLE

*A/C = ACROSS CORNERS, A/F = ACROSS FLATS

F

E

(34.9)

1.375

(45.7)

1.80

(28.2)

1.109

(38.9)

1.53

(22.2)

0.875

(33.0)

1.30

(22.2)

0.875

(33.0)

1.30

(mm)

INCH

- I -

A/F*

(mm)

INCH

- H -

G

H

CAT.NO.S IN TABLE
UPDATED TO REFLECT
NO. CALLED OUT ON DCN

22362, UPDATED NOTE 4
PER DCN 23274. MYA

8/15/17

DJP

2

LIST OF PARTS- LOCKNUT
NYLON, NATURAL WAS
STEEL, ZINC PLATE

PER DCN 23274. RM

2/1/18

EJM

3

LIST OF PARTS- LOCKNUT
NYLON, NATURAL/BLACK
WAS NATURAL

PER DCN 23596. RM

2/21/18

EJM

4