Hubbell PGR Installation, Operation And Service Instructions

Hubbell Lighting, Inc.

LED Replacement

Contact factory

SERVICE

PGR LED Sconce

High Performance LED Sconce

For Indoor or Outdoor Application

Installation, Operation and Service Instructions

RECYCLING INFORMATION

All steel, aluminum and thermoplastic parts
are recyclable.
All cartons contain recycled materials.

Please recycle responsibly.

US Patent No. D627,916

93021413

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed including the following.

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

1. Do not let power supply cords touch hot surfaces.

2. Do not mount near gas or electric heaters.

3. Equipment should be mounted in locations and at heights where it will not readily be subject

to tampering by unauthorized personnel.

4. The use of accessory equipment not authorized by the manufacturer may cause an
unsafe condition.

5. Do not use this equipment for other than its intended purpose.

6. Servicing of this equipment should be performed by qualified service personnel.

INSTALLER:

•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS

•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT

Copyright© Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in U.S.A.

Hubbell Lighting, Inc. Life Safety Products • www.dual-lite.com

93036103 B 5/2011

93021413
93021935
93036104
93036105
93021938
93021939

WARNING – This product contains chemicals known to the State of California to cause cancer, birth

defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,

or otherwise touching this product.

Screw

O-Ring

Backplate

93021938

INSTALLATION

1.Open the unit by loosening both screws on top of unit until screws spin freely. Pry cover

from backplate, and remove cover squarely from backplate. (Remove screws prior to
re-installing cover.)

IMPORTANT:
Once unit is connected and cover is snapped onto backplate, gently seat screws onto
O-ring seals to less than 1/2FT-LB (.7N-m).
DO NOT OVERTIGHTEN!
O-RING MAY BE DAMAGED AND THE UNIT WILL LEAK IF ABOVE IS NOT
FOLLOWED.

Unit will operate from 6 through 12VDC.

OPERATION

Cover

2.Remove 7/8” diameter K.O. from backplate if mounting to electrical
box or remove 1/2”-1/4NPT pipe plug if using conduit.

CONDUIT MOUNTING:

If unit is not secured to mounting surface using unit backplate

K.O. pattern and supplied gasket, use sealant to create

waterproof seal between the mounting surface and the unit
backplate.

IMPORTANT!

To weatherproof your outdoor installation, be sure to seal all
fixture openings - mounting, conduit, etc.

3.Remove appropriate backplate K.O.’s

93036104

DC Wire Harness

for electrical box screws.

6. Connect DC supply wires to
DC harness wires

To Building Ground Wire

4.Peel backing from J-Box Gasket and adhere to
backplate around center K.O.

93021935

5.Feed building wires through center K.O. as

shown and secure backplate using screws
supplied with electrical box.

Ground

6VDC
through
12VDC

NOTE:
Feed wires and nuts back into electrical box through

backplate as shown.

Connect ground (green) conductor.

CAUTION: OBSERVE POLARITY

Connect blue (+) conductor to building
(+) DC supply. Connect yellow (-)
conductor to building (-) DC supply

Full Cut-off Shield Installation

93021939

7.Connect DC wire harness from unit backplate
to J1 on power supply PCB.

93036105

8.Attach unit cover to backplate

by reversing Step 1. Ensure all
wires are within enclosure to avoid
pinching with cover.

TABS “A”

Pinch sides inward

1.Slide tabs “A” between housing and lens gasket.

2.Pinch sides of shield inward and seat shield against lens.

3.Release pinched sides of shield to secure to unit.