Hubbell PGN Installation, Operation And Service Instructions
LED Replacement
Contact factory
SERVICE
PGN LED Sconce
High Performance LED Sconce For Indoor
Or Outdoor Application
Installation, Operation and Service Instructions
RECYCLING INFORMATION
All steel, aluminum and thermoplastic parts
are recyclable.
All cartons contain recycled materials.
Please recycle responsibly.
PATENTS
PENDI NG
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following.
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. Do not let power supply cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.
4. The use of accessory equipment not authorized by the manufacturer may cause an
unsafe condition.
5. Do not use this equipment for other than its intended purpose.
6. Servicing of this equipment should be performed by qualied service personnel.
Copyright
93021413
93021935
93021936
93021937
93021938
93021939
©
Hubbell Lighting, Inc., All Rights Reserved • Specications subject to change without notice. • Printed in U.S.A.
Hubbell Lighting, Inc. Life Safety Products • www.dual-lite.com
93020531 A 2/09
INSTALLER:
•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
WARNING – This product contains chemicals known to the State of California to cause cancer, birth
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,
or otherwise touching this product.
Screw
O-Ring
Backplate
93021938
INSTALLATION
1.Open the unit by loosening both screws on top of unit until screws spin
freely. Pry cover from backplate, and remove cover squarely from
backplate. (Remove screws prior to re-installing cover.)
IMPORTANT:
Once unit is connected and cover is snapped onto backplate, gently
seat screws onto O-ring seals to less than 1/2FT-LB (.7N-m).
DO NOT OVERTIGHTEN!
O-RING MAY BE DAMAGED AND THE UNIT WILL LEAK IF ABOVE
IS NOT FOLLOWED.
Unit will operate from 120 or 277VAC, 6 through 12VDC.
OPERATION
NOTE: In order for unit to function properly as emergency lighting (NEC 700.12), DC emergency
supply must be powered from same normal AC supply as that to unit.
NOTE: This unit does not provide transfer logic. DC voltage supplied to unit will take priority over the
AC supply, and unit will operate from the DC supply whenever both AC and DC voltages are present.
Cover
2.Remove 7/8” diameter K.O. from backplate if mounting
to electrical box or remove 1/2”-1/4NPT pipe plug if
using conduit.
CONDUIT MOUNTING:
If unit is not secured to mounting surface using
unit backplate K.O. pattern and supplied gasket,
use sealant to create waterproof seal between the
mounting surface and the unit backplate.
IMPORTANT!
To weatherproof your outdoor installation, be sure to
seal all xture openings - mounting, conduit, etc.
3.Remove appropriate backplate
93021936
AC Wire Harness DC Wire Harness
7.Connect transformer AC wire harness
to AC wire harness on unit backplate.
K.O.’s for electrical box screws.
6.Connect building AC
wires to transformer
harness wires. Connect
DC supply wires to DC
harness wires
To Building Ground Wire
8.Connect DC wire harness from unit
backplate to J1 on power supply PCB.
4.Peel backing from J-Box Gasket and
adhere to backplate around center K.O.
93021935
5.Feed building wires through center
K.O. as shown and secure back-
plate using screws supplied with
electrical box.
120VAC
277VAC
Ground
6VDC
through
12VDC
NOTE:
Feed wires and nuts back into electrical box
through backplate as shown.
Connect black (hot) and neutral
(white) to supply. Cap off
unused (red) conductor.
Connect red (hot) and neutral
(white) to supply. Cap off
unused (black) conductor.
Connect ground (green)
conductor.
Connect blue (+) conductor to
building (+) DC supply. Connect
yellow (-) conductor to building
(-) DC supply
Full Cut-off Shield Installation
93021939
93021937
9.Attach unit cover to backplate
by reversing Step 1. Ensure
all wires are within enclosure to
avoid pinching with cover.
TABS “A”
Pinch sides inward
1.Slide tabs “A” between housing and lens gasket.
2.Pinch sides of shield inward and seat shield against lens.
3.Release pinched sides of shield to secure to unit.
Loading...