Hubbell P020A480120R Installation Manual

LINKOSITYTM POWER SYSTEM SUPPL Y ASSEMBL Y (PSSA)

INST ALLATION INSTRUCTIONS

General Information

• CAUTION: RISK OF ELECTRIC SHOCK. Do not
apply power before completely installing

• This equipment is intended for installation in ordinary
locations in accordance with national and local electri­cal codes.

• For installation by a qualified electrician in accordance
applicable codes and standards for the jurisdiction in
which the LINKOSITY™ power system is to be
installed.

• Confirm device rating is proper for application.

• CAUTION: RISK OF ELECTRIC SHOCK OR

FIRE: The load (output) connectors are not rated
for current rupture and MUST NOT be used for
disconnection under load.

• When connecting cable set to PSSA the coupling nut is
to be made wrench tight; ¼ turn pass hand-tight.

• Verify all connections are properly secured.

• When connecting to LINKOSITYTM connectors the cou-

pling nut is to be made wrench tight; ¼ turn beyond hand­tight

Mounting Options:

• Panel mount – Enclosure Type 1

Feeders to the Primary

The feeders to the PSSA MUST be run in accordance with
the applicable codes and standards for the jurisdiction in
which the LINKOSITY power system is to be installed.
Accepts #14 - #6 AWG copper conductor, Torque 35
pounds for #10 - #14 AWG, Torque 40 pounds for #6 - #8
AWG

Positioning & Mounting:

• Ventilation openings are NOT to be obstructed.

• Ventilation clearances MUST NOT be less than 6

inches (.15m) all around assembly. Front of assembly
MUST remain accessible for inspection & mainte­ nance.

• Typical working space requirement in front of PSSA:
o Depth:

 3 feet (0.9m) with no live or grounded parts on
other side of the working space, or
 3.5 feet (1m) when installed across from a
grounded surface, or
 4 feet (1.2m) when installed across from
exposed live parts

o Headroom to be equal or greater than 6.5 feet (2m)
o Width to be width of the equipment or 2.5 feet

(0.75m) whichever is greater

o Shall permit at least a 90° opening of PSSA door
Note: Working space must be acceptable to the
inspection Authorities Having Jurisdiction in the
jurisdiction in which the LINKOSITY™ power
system is to be installed

• Required dedicated equipment space MUST equal the
width and depth of the PSSA and extending from
floor to a height of 6.5 feet (2m) or to the structural
ceiling, whichever is lower.

Grounding Electrode Conductor
CAUTION: RISK OF ELECTRIC SHOCK. PSSA MUST be

effectively grounded to the premises grounding electrode
system in accordance with the National Electrical Code.

Reference:

LINKOSITY™ Power System Installer’s Guide
Websites:
http://www.hubbell-wirring.com
http://www .linkosity.com

UL Listing Information

• UL Listed to UL508A as an Industrial Control Panel
intended for general use in ordinary location in accor­dance with the National Electrical Code.

• Not Listed for use with:
a) fire pump controllers,
b) industrial control panels for use in hazardous
(classified) locations;
c) industrial control panels with intrinsically safe
circuits that extend into a hazardous (classified)
location (i.e. the panel contains one or more
intrinsic safety barriers, shunt – diode barriers,
or zener barriers);
d) pre-fabricated buildings, structures or platforms
for support of persons;
e) controls for fuel dispensing equipment (e.g.
gasoline pumps);
f) controls for swimming pools or spas;
g) controls for emergency lighting and power
equipment;
h) fire or emergency alarm equipment;
i) gas or vapor detection equipment;
j) termination boxes (containing terminals for
connecting conductors of power or distribution
circuits);
k) portable power distribution equipment, (plug
and receptacle input and output, power
distribution only, no control circuit) for
construction sites, theaters, motion picture and
television studios, carnivals, circuses, fairs and
exhibition halls;
l) the controlled equipment supplied from an
industrial control panel, such as motors, pumps,
machines, robots, air conditioners, etc.

Wiring Device-Kellems
Hubbell Incorporated
185 Plains Road
Milford, CT 06461-2420
[phone]

PD2145 5/06

LINKOSITY TM is a trademark of Lockheed Martin.