Hubbell K-18 User Manual

INSTALLATION and MAINTENANCE INSTRUCTIONS
“K-18” DUAL HOSE REEL-DIRECT DRIVE
All units are provided with right hand rotation unless otherwise specified. This means that hose is pulled off spool top left or bottom right (spool rotates clockwise to wind hose) when viewing spring end of reel. See diagram on parts page.
Clock-type springs provide power for automatic hose take-up. Spring must be pretensioned at time of installation to insure that tension is applied to hose at all times. A tension adjustment spanner wrench is provided with each reel.
WARNING
If machine pull reel, move machinery to position closest to reel before adjusting spring tension. Adjusting tension with hose extended may result in damage to reel or personal injury.
INSTALLATION
1. Install hoses if reel was purchased without hoses. See instructions on page 4.
2. Insure that machinery to be serviced by reel is at position closest to reel.
3. Securely mount reel in desired position using 1/2"(M12). Be sure spool is aligned with hose run.
WARNING
Some reels with large or multiple springs are equipped with a ratcheted adjustment wrench. Follow separate instructions for its use. Failure to use ratcheted wrench, on reels so equipped, could result in serious personal injury.
MAINTENANCE
Periodically:
A. Inspect hose for wear and check mounting bolts and other hardware for tightness. B. Check for broken springs by pulling about 2/3 hose off
“IN” with 2/3
cable off reel–
SPRING OK
BROKEN SPRING
INDICATORS
reel and observing “Broken Spring Indicators” on sides of spring canisters (Fig. 3). NOTE: Bearings and springs are prelubricated and require no periodic
“OUT” with 2/3
cable off reel–
SPRING
BROKEN
Figure 3
maintenance.
WARNING
Do not attempt to remove spring from its housing. Clock type springs can be dangerous to handle. Removal of spring from housing could result in personal injury.
4. Connect free end of hoses to connections on machine.
5. Connect flexible supply lines to swivel fitting. See HOSE INSTALLATION REFERENCE DRAWING.
NOTE: Do not hard plumb to swivel fitting.
6. Remove cover plate on spring housing to expose shaft and spring hub. (See Figure 1).
7. Insert spanner wrench into holes in spring hub (Fig 2). Rotate spanner wrench counter-clockwise. Number of 360° turns should match last digit in model number on serial plate.
Figure 1
SPRING
HOUSING
SPRING
HUB
PLATE
Figure 2
COUNTERCLOCKWISE
FOR STANDARD
ROTATION
SPANNER
WRENCH
CAUTION
Do not exceed number of turns indicated on serial plate. Over-tensioning can cause a broken spring, sheared shaft or other damage.
WARNING
Do not attempt to relieve spring tension using spanner wrench. Doing so may result in personal injury.
SPRING REPLACEMENT
The unique SAFETYCHANGE® spring motor consists of a spring and hub sealed within a housing. A replacement spring is supplied sealed in its housing and the old unit should be discarded completely.
1. Turn off supply pressure to reel.
2. Insure that machinery to be serviced by reel is at position closest to reel. Disconnect hose from machine connections.
3. Wind all hose onto reel to relieve all spring tension.
4. Remove inspection cover from face of spring housing.
5. Rotate spool clockwise and observe inner shaft. Shaft should rotate clockwise and hub (with spring attached) should remain stationary.
NOTE: Do not attempt to remove spring if resistance is met
or hub tends to rotate with shaft. Continue to rotate spool and
strike end of shaft several sharp blows with a rubber mallet until
shaft rotates freely and hub remains stationary.
6. Remove (4) bolts which secure spring motor to frame.
7. Slide spring motor off shaft and discard.
8. Install replacement spring motor, pawls and pawl springs.
NOTE: Pawl springs must be located between the pawls
and the deepest section of the shaft grooves.
Make sure that pawls and pawl springs are inserted flush
with ends of shaft and hub or they may rub against
inspection cover. See Fig 4, page 4.
9. Tighten bolts securing spring housing to reel frame.
CONTINUED ON BACK PAGE
13
1
1
1
1
8
5
5
2
2
6
4
15
1
1
17
16
9
9
11
19
18
14
11
12
3
10
4
13
4
3
3
3
3
7
11
11
20
19
18
14
14
12
3
10
DIRECT DRIVE “K-18” DUAL HOSE REEL
REPLACEMENT PARTS LIST
ITEM KIT NO. DESCRIPTION QTY.
1 015521
1 015522 Frame Assembly (-6 hose code)* Kit 1
1 015523 Frame Assembly (-8 hose code)* Kit 1
2 015535 Spool Discs-18" (Set of two) 1
3 015539
3 015540 Main Shaft Kit (-6 hose code)* 1
3 015541 Main Shaft Kit (-8 hose code)* 1
4 015543
4 015544 Wrapper Kit (-6 hose code)* 1
4 015545 Wrapper Kit (-8 hose code)* 1
5 015547
6 015548
7 700079 Swivel Kit (-4 hose code)* 1
7 700080 Swivel Kit (-6 hose code)* 1
7 700081 Swivel Kit (-8 hose code)* 1
8 017190 Spanner Wrench (35–80 Springs) 1
8 017191 Spanner Wrench (100 Springs) 1
9 032805 Ratchet Wrench (35–80 springs) 1
9 032804 Ratchet Wrench (100 springs) 1
10 012425
10 012426 Pawl Kit (62–80 Springs) AR
10 012427 Pawl Kit (100 Springs) AR
Frame Assembly (-4 hose code)* Kit
(Includes frame and swivel bracket)
Main Shaft Kit (-4 hose code)*
(Includes shaft, center tube, retaining ring and drive pin)
Wrapper Kit (-4 hose code)*
(Includes 2 covers and 4 spacers)
Bearing Kit–Swivel End
(Includes bearing and housing)
Bearing Kit–Spring End
(Includes bearing, housing and gasket)
Pawl Kit (35–60 Springs)
(Includes 2 pawls and springs)
1
1
1
1
1
AR
ITEM KIT NO. DESCRIPTION QTY.
11 017041
11 017042 Spring Motor Kit, Rev. Rot.–35 AR
11 017043 Spring Motor Kit, Std. Rot.–60 AR
11 017044 Spring Motor Kit, Rev. Rot.–60 AR
11 017045 Spring Motor Kit, Std. Rot.–62 AR
11 017046 Spring Motor Kit, Rev. Rot.–62 AR
11 017047 Spring Motor Kit, Std. Rot.–75 AR
11 017048 Spring Motor Kit, Rev. Rot.–75 AR
11 017049 Spring Motor Kit, Std. Rot.–80 AR
11 017050 Spring Motor Kit, Rev. Rot.–80 AR
11 017051 Spring Motor Kit, Std. Rot.–100 AR
11 017052 Spring Motor Kit, Rev. Rot.–100 AR
12 014200 Stub Shaft, Std. Rot. (351)** 1
12 01420001 Stub Shaft, Rev. Rot. (351)** 1
12 014202 Stub Shaft, Std. Rot. (621, 751, 801)** 1
12 01420201 Stub Shaft, Rev. Rot. (621, 751, 801)** 1
12 016306 Stub Shaft, Std. Rot. (622, 752, 801)** 1
12 01630601 Stub Shaft, Rev. Rot. (622, 752, 801)** 1
12 014204 Stub Shaft, Std. Rot. (1001)** 1
12 01420401 Stub Shaft, Rev. Rot. (1001)** 1
13 015564 Nitrile - Hydraulic Fluid, Water, Pueumatic 1
13 015565 Propyl - Phosphate Ester Base 1
13 015566 Vitron - Pydraul 135 1
14 017054
14 017055 Extension Bolts (100 Springs) AR
15 016182 Carriage Bolt, .50–13 x 1.5 AR
16 021291 Lockwasher, .56 Med., Z.P. AR
17 100959 Hex Nut, .50–13, Z.P. AR
18 101211 Flat Washer, .50 AR
19 P06-03 ESNA Lock Nut, .50–13, Z.P. AR
20 021762 Hub Lock Pins (100 Springs) AR
20 021761 Hub Lock Pins (All Other Springs) AR
* Refer to Model Number Structure on following page. Reel model number is found on serial plate affixed to reel. **Indicates spring size and number of springs. Example: 621=one 62 size spring.
Spring Motor Kit, Std. Rot.–35
(Includes pawls, pawl springs, cover, gaskets, and snap ring)
Replacement Seal Kits (-4, -6, -8 hose code):
Extension Bolts (62, 75, 80 Springs)
(4 bolts per kit–less hardware)
AR
AR
13
1
1
1
1
8
5
5
2
2
6
4
15
1
1
17
16
9
9
11
19
18
14
11
12
3
10
4
13
4
3
3
3
3
7
11
11
20
19
18
14
14
12
3
10
TO DETERMINE ROTATION OF REEL
Always specify
SERIAL NUMBER & MODEL NUMBER
when ordering parts.
STANDARD
ROTATION
Hose is played out and retracted as shown
when viewing reel from spring motor side.
REVERSE
ROTATION
Reel Model Number Structure
REEL TYPE
SPOOL DIAMETER
SPRING MODEL
K 18 75 1 - 4 - 1
PRETENSION TURNS
HOSE CODE
QUANTITY SPRINGS
4 =1/4" i.d. hose 6 =3/8" i.d. hose 8 =1/2" i.d. hose
10. Connect free end of hose to connections on machine or adjust hose stop so that desired length of hose extends from reel.
11. Tension spring with spanner wrench. Refer to INSTALLATION section.
12. Replace inspection cover.
SPOOL SHAFT
Figure 4
SIDE VIEW
PAWL
Install
against flat
END VIEW
SPRING HUB
(Spring not
shown)
SHAFT
GROOVE
HOSE REMOVAL
Use the following procedure to remove worn or damaged hoses from reel prior to installation of new hoses.
1. Move machine serviced by reel to a position closest to reel. Spring will still be under pre-tension at this point.
2. Turn off supply pressure to reel.
3. Disconnect hoses from machine or other attachments. Remove hose stops, if installed, and allow hoses to retract onto spool. Ensure all tension is off spring by manually rotating spool (normally clockwise when viewed from spring side).
4. Unwrap hoses without allowing spool to turn.
5. Disconnect hoses from elbows inside spool wrapper.
6. Install new hoses following directions below.
HOSE INSTALLATION REFERENCE DRAWING
DIRECTION TO WIND HOSE WHEN
Use the following procedure to replace hoses or if reel was ordered without hoses. Refer to HOSE INSTALLATION REFERENCE DRAWING, below.
1. Unspool new hose from shipping spool and lay out to eliminate twist.
NOTE: This step is not essential, but will aid in winding
operation of the reel and prolong hose life.
2. Connect hoses to elbows inside spool wrapper. (See drawing below.)
3. Wind the hose onto the reel spool by hand rotating spool in direction it turns free of spring tension. (Normally clockwise when viewed from spring side)
4. Complete working end connections.
5. Pretension reel and complete installation as described in REEL INSTALLATION section.
STANDARD SPOOL ROTATION
VIEWED FROM FITTING SIDE
SPOOL
DISK
HOSE INSTALLATION
REEL
FRAME
CONNECT SPOOLED
HOSES
HERE
SPOOL WRAPPER SECTIONS
VIEW FROM FITTING SIDE
SPOOL
DISK
HOSE ON
SPOOL
SWIVEL FITTING
SUPPLY
LINES
NOTE: SUPPLY
MUST BE FLEXIBLE
LINE. DO NOT HARD
PLUMB.
P.O. Box 26 • 600 South Clark St.
Phone 920–387–4120 • Fax 920–387–4189
SPRING MOTOR
MOUNTING
BASE
GLEASON REEL CORP.
Mayville, WI 53050–0026
Printed in USA Bulletin No. 052761.b
Loading...