Hubbell CCE User Manual

CCE

Thin Die-Cast LED EXIT Sign

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

READ AND FOLLOW ALL SAFETY

1. Do not use outdoors.

2. Do not let power supply cords touch hot surfaces.

3. Do not mount near gas or electric heaters.

4. Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.

5. The use of accessory equipment not authorized by the manufacturer may cause an unsafe condition.

6. Do not use this equipment for other than its intended purpose.

7. Servicing of this equipment should be performed by qualified service personnel.

8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units once a month for a
minimum of 30 seconds, and once a year for a minimum of 90 minutes.

•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS

•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT

WARNING – This product contains chemicals known to the State of California to cause cancer, birth

defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,

or otherwise touching this product.

Parts Description (All parts provided unless noted otherwise)

 Face Plate
 Back Plate
 Mounting Hole Cover
 Red or Green Lens
 Canopy
 Junction Box Screws (not shown)
 Wire Nuts
 Junction Box (not provided)
 Mounting Bracket
 Input WIres

always be followed including the following.

INSTRUCTIONS

INSTALLER:

NOTE: This xture is for use only with 3 ½" octagon, 4" octagon, 4" square or single-gang junction boxes, on an unswitched circuit. See Wiring
Diagrams and “To Remove Directional Indicators” below before beginning xture installation. On xtures with battery: Connect battery only after

continuous power can be supplied to the xture. Allow 24 hours before initial test or for full charge.

INSTALLATION

Back Mounting (Single Face Units Only)

1. Turn off AC power.

2. Remove appropriate knockouts in backplate of EXIT sign enclosure.

Knockouts are not intended for use with conduit ttings.

3. Feed power supply module input wires from EXIT sign
through the open knockout. Route wires along side walls of

enclosure to assure proper sign illumination and to protect

wires from damage.

4. Connect building supply wires to the power supply module

input wires and feed splices into the junction box. For
120V supply connect the line wire to the black lead and for
277V supply connect the line wire to the orange lead. Connect

neutral wire to the white lead. The ground wire (green lead) must be
connected in accordance with local codes. CAUTION: The unused black or orange wire must be capped

with wire nut or other approved insulator. Failure to do so may cause an unsafe condition.

5. Attach EXIT sign backplate to junction box with supplied screws.

6. After AC power can be continuously supplied, push in connector from battery (if provided) to LED board.

7. Snap EXIT faceplate into place on EXIT sign backplate.

8. Turn on AC power.

INSTALLATION

Top or End Mounting (Single or Double Face Units)

1. Turn off AC power.

2. Install the Mounting Bracket to the junction box with supplied screws.

3. Prepare EXIT faceplate (two faceplate’s for Double Face signs) by removing

directional indicator knockout(s) as required.

4. Secure the Canopy to the EXIT sign enclosure by removing the appropriate

Mounting Hole Cover and tting Canopy onto enclosure. Secure Canopy to

enclosure with two screws.

5. Feed power supply module input wires from EXIT sign through the Canopy.

Route wires along side walls of enclosure to assure proper sign
illumination and to protect wires from damage.

6. After AC power can be continuously supplied
, push in connector from battery (if

provided) to LED board.

7. Snap EXIT faceplate into place on EXIT
sign backplate or second EXIT faceplate
for Double Face sign. Assure that canopy

is positioned securely.

8. Connect building supply wires to the power supply module input wires and feed splices into the junction

box. For 120V supply connect the line-wire to the black lead and for 277V supply connect the line wire to

the orange lead. Connect neutral wire to the white lead. The ground wire (green lead) must be connected in
accordance with local codes. CAUTION: The unused black or orange wire must be capped with wire nut or

other approved insulator. Failure to do so may cause an unsafe condition.

9. Secure the Canopy to the Mounting Bracket with supplied screws.

10. Turn on AC power.

To Remove Directional Indicators

Use punch or similar tool to tap out the
desired knockout along its inside edges

BATTERY BACKUP AC ONLY

WIRING DIAGRAM

RECYCLING INFORMATION

All steel, aluminum and thermoplastic parts are recyclable.

NOTICE: Emergency units contain rechargeable batteries which

must be recycled or disposed of properly.

Compass Life Safety by Hubbell Lighting, Inc.• www.compasslightingproducts.com

©

Copyright

Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in China

COMP0006_CCE_INST_SHT 04/13