Hubbell 67L Installation Instructions Manual

INSTALLATION INSTRUCTIONS

AIRCRAFT

FEED

CABLE

FIXTURE SERIES: 67L

FIXTURE LENGTH
MINUS .75"

AIRCRAFT CABLE

.38" TYP

MOUNTING TYPE: AIRCRAFT CABLES

PAGE: 1 OF 3

CEILING
REFERENCE

FEED

.38"
TYP

END
CAP

AIRCRAFT
CABLE

END CAP

SIDE VIEW - INDIVIDUALLY MOUNTED

FIXTURE LENGTH
MINUS .75"

AIRCRAFT
CABLE

AIRCRAFT
CABLE

END CAP
FIXTURE LENGTH

(24", 36", 48", 72", OR 96")

AIRCRAFT
CABLE

FIXTURE
LENGTH

AIRCRAFT
CABLE

END
CAP

2.00"

3.69"

BELL LENS
SHOWN

SIDE VIEW - ROW MOUNTED

GENERAL NOTES: (READ SHEETS COMPLETELY BEFORE STARTING)

1. LEAVE PROTECTIVE WRAPPING ON FIXTURE(S) UNTIL START OF
INSTALLATION.

2. FIXTURES ARE SUPPLIED WITH FACTORY-INSTALLED BRANCH CIRCUIT
WIRING. REFER TO SUPPLEMENTAL INSTRUCTION SHEET WEHN MAKING
CONNECTIONS.

3. APPROXIMATE WEIGHT OF FIXTURE IS 2 LBS PER FOOT OF LENGTH.

4. REFER TO PAGE 3 FOR LENS INSTALLATION/REMOVAL INSTRUCTIONS.

DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN.

litecontrol.com

IF YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT, PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.

TOOLS REQUIRED

- SCREWDRIVER/DRILL

- 11/32" NUT DRIVER

3.56"

CROSS SECTION VIEW

SUPPLIED BY INSTALLER

DRAWING: 510641
REV / DATE: 0 / 1/16/2019

INSTALLATION INSTRUCTIONS

REMOVE LENS, REFERRING TO PAGE 3. LOCATE AIRCRAFT CABLES ALONG

1

STRAIGHT LINE IN CEILING PER DIMENSIONS SHOWN ON PAGE 1. REFER TO
CABLE INSTRUCTION SHEET 510541 FOR ATTACHMENT TO CEILING.

FIXTURE SERIES: 67L

2

MOUNTING TYPE: AIRCRAFT CABLES

PAGE: 2 OF 3

INSERT FLAT STRAP INTO
CHANNEL IN HOUSING
(MARKED IN BLUE). INSERT
CABLE GRIPPER THROUGH
HOUSING AND THREAD INTO
FLAT STRAP. REPEAT AT EACH
CABLE LOCATION.

AT END OF FIXTURE, INSERT
FLAT STRAP COMPLETELY
INTO HOUSING SUCH THAT
CABLE GRIPPER IS THREADED
INTO HOLE A. AT FIXTURE
JOINT, INSERT FLAT STRAP
PARTIALLY SUCH THAT HOLE B
IS USED.

IF INSTALLING INDIVIDUAL FIXTURE: LEVEL

3 4

FIXTURE BY SLIDING CABLE GRIPPERS UP/DOWN.
SKIP TO STEP 5.

FLAT
STRAP

CABLE GRIPPER

B

FLAT
STRAP

A

RAISE FIXTURE (1ST FIXTURE OF ROW) UP TO
CEILING. ATTACH TO AIRCRAFT CABLE

REMOVE 5/8" PLUG BUTTON AT FEED LOCATION.
INSERT UNIVERSAL BUSHING INTO FEED HOLE
AND ROUTE FEED CORD THROUGH BUSHING
INTO FIXTURE WIREWAY. MAKE ELECTRICAL
CONNECTIONS.

5

#8 SMS

FEED
CORD

BUSHING

5/8" FEED
HOLE (PLUG
REMOVED)

END
CAP

1/4-20 MS

RAISE NEXT FIXTURE IN ROW; ATTACH TO AIRCRAFT
CABLE IN CEILING. ROUTE WIRING THROUGH FIXTURE
JOINT AS SHOWN. INSERT PROTRUDING FLAT STRAP OF
PREVIOUS FIXTURE INTO CHANNEL OF NEW FIXTURE.
SECURE BY INSERTING 1/4-20 MACHINE SCREW
THROUGH HOUSING TOP AND FLAT STRAP.

litecontrol.com

DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN.
IF YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT, PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.

NUT

(LED REFLECTOR
MODULES HIDDEN

8-32 MS

SECURE JOINT USING (2) 8-32 MACHINE SCREWS AND
NUTS. DO NOT TIGHTEN UNTIL FIXTURES ARE ALIGNED;
LEVEL BY SLIDING CABLE GRIPPERS UP/DOWN. REPEAT
STEPS 3-4 FOR EACH ADDITIONAL FIXTURE IN ROW.

FOR CLARITY.)

ATTACH END CAP AT BOTH ENDS OF FIXTURE OR ROW OF
FIXTURES USING (2) #8 X 1/4" LONG SHEET METAL SCREWS.
ENSURE END CAP IS FLUSH WITH HOUSING WALLS.

CLEAN FIXTURE EXTERIORS WITH GENERAL WINDOW
CLEANER. REATTACH LENS PER PAGE 3.

DRAWING: 510641
REV / DATE: 0 / 1/16/2019