Hubbardton Forge W009171999 Installation & Assembly

Assembly & Installation Instructions A409

Tempo, Cadence & Rhythm Kitchen Pendants 18740, 18742 & 18744 Page 1 of 3

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735 33366

These instructions will be used for the following Fixtures:

Stem Assembly (Figure 1)

Component Parts

A Fixture Pipe
B Fixture Coupling

1. Carefully unpack the fixture from the carton.

2. Carefully slip fixture pipe (A), threaded end first, over fixture wires.

3. Apply a drop of the supplied thread locking compound to the threads
of fixture pipe (A) and screw pipe into fixture coupling (B), being
careful not to twist or pinch the wires.

Note: Application of the thread locking compound is necessary to
prevent the stem from loosening during regular maintenance and
cleaning of the fixture. Be certain to apply the compound.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

18740 18742 18744 (shown)

Assembly & Installation Instructions A409

Tempo, Cadence & Rhythm Kitchen Pendants 18740, 18742 & 18744 Page 2 of 3

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735 33366

Prepare the Canopy (Figure 2)

Component Parts

C Crossbar
D Jam Nut
E Threaded Nipple
F Canopy
G Canopy Ring

Caution: Be sure power is off at the main breaker box prior to installation.

1. Thread the jam nut (D) and crossbar (C) onto threaded nipple (E); leave both
parts loose.

2. Using two machine screws (not provided), temporarily fasten the crossbar (C) to
the electric box. Note: A new electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new fixture.

3. Adjust the length of threaded nipple (E) in crossbar (C) so that canopy ring (G)
will hold canopy (F) against the ceiling with no threads showing for best
appearance. When the correct adjustment is established, tighten jam nut (D)
against crossbar (C) to hold the adjustment.

4. Remove the crossbar (C) with stem from the electrical box and proceed with the
assembly instructions on following page.

Install Glass (Figure 3)

Component Parts

L Socket
M Washer (not needed on 18740)
N Spacer Ring
O Retaining Ring with Cover
P Glass

1. Remove retaining ring with cover (O), spacer ring (N) & washer (M) from
socket (L). Retain for later use. Parts ship installed.

2. Slide glass (P) over socket (L) followed by washer (M) and spacer ring (N).

Note: Washer (M) not needed on 18740 Fixture.

3. Thread retaining ring with cover onto socket to secure glass (P). Do not
over tighten ring (O).

4. Install bulb into socket (L).

5. Restore electricity at main breaker.

(continued)

(Figure 2)

(Figure 3)

Assembly & Installation Instructions A409

Tempo, Cadence & Rhythm Kitchen Pendants 18740, 18742 & 18744 Page 3 of 3

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735 33366

Install Fixture (Figure 3 & 4)

Component Parts

A
B Fixture Pipe
C Crossbar
F Canopy
G Canopy Ring

H Canopy Pipe
I Ground Screw
J Clutch
K Set Screw

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully slide canopy ring (G) and canopy (F) down over fixture pipe (A)
until they rest on the fixture. Make sure smaller diameter side of canopy ring
(G) is oriented up toward the canopy (Figure 3).

2. Slip wires from the fixture pipe (A) through the canopy pipe (H).

3. Unscrew the clutch (J) from the canopy pipe (H); slide it across the wires
and onto the fixture pipe (A). Follow this with the plastic sleeve, oriented so
the tapered end nests in the clutch (J) (Figure 4)

4. Slide the canopy pipe (H) on to fixture pipe (A) as far as necessary to give
you the total length of the fixture, which you desire. Be careful not to scratch
the pipe surfaces and to pull excess wire up through the canopy pipe (H).
There must be a minimum 1-1/2" of inner pipe inside the outer pipe. Hand­tighten the clutch to temporarily hold this adjustment. The clutch is not
securely fastened at this point; do not depend on it to hold the fixture.
Important: To ensure full connection strength, be sure the tapered end of
the plastic clutch sleeve is oriented toward the clutch when assembled and
securely tighten set screw (Figure 4).

5. Using two machine screws (not provided), fasten the crossbar (C) to the
electric box.

Note: A new electric box comes with screws. When replacing a fixture,
retain the existing screws for use with the new fixture.

6. Using suitable wire connectors (not provided), connect fixture wires to
supply wires (white to white supply, black to black supply). Run a pigtail
lead from crossbar ground screw (I) to the junction box and connect all
ground wires (bare copper or green to bare copper or green). Push
wires back into outlet box. Caution: Make sure wire connectors
are twisted on securely, and no bare wire is exposed.

7. Slide canopy (F) against ceiling, and secure with canopy ring (G).

8. Once the fixture is fastened to the ceiling, tighten the set screw (K)
firmly with hex wrench provided.

9. Restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

(Figure 4)

(Figure 5)