ASSEMBLY & INSTALLATION INSTRUCTIONS
Link Multiport Round 9lt Pendants 131100 & 131108
A774
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49669 Rev A
1 OF 8
ASSEMBLY & INSTALLATION INSTRUCTIONS
Link Multiport Round 9lt Pendants 131100 & 131108
Component Parts
A Canopy
B Canopy Cover Plate
C #10 Screws (8)
D Anchors (4)
E Ground Screw
F Cupped Washer
G Safety Cable (4)
A774
H Safety Cable Nut (4)
I Studs (4)
J Gripper (9)
K Supply/Support Cable (9)
L Transformer
M Wire Connector (8)
N Cap (4)
O Fixture (9)
P Socket (9)
Q Bulb (9) (sold separately)
R Glass (9)
S Screws (36)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49669 Rev A
2 OF 8
ASSEMBLY & INSTALLATION INSTRUCTIONS
Link Multiport Round 9lt Pendants 131100 & 131108
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products and options.
To Install Canopy (Figure 1 - on following page)
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
1. Carefully unpack canopy and xture from the carton.
2. Locate canopy (A). Remove caps (N) from studs (I) in canopy (A) and set canopy cover plate (B) aside for later use
3. The canopy will need to be secured to a structural member in the ceiling. For additional holes needing anchors,
place canopy (A) over the electrical box. Line up holes in canopy with holes in electrical box. With a pencil, mark the
location of mounting holes needing anchors in canopy on ceiling. Set canopy (A) aside.
4. Drill 1/4" holes in the locations marked on the ceiling. Place the tapered end of the anchors (D) into the holes and
gently tap them ush to the ceiling using a light weight hammer.
A774
5. Thread the wires in the electrical box through the hole in the canopy (A) while moving the canopy into position. Using
two machine screws (not provided) fasten canopy (A) to the electric box.
Note: A new electric box comes with screws. When replacing a fixture, retain the existing screws for use with the new fixture.
6. Using wood screws (C) attach canopy (A) to a structural member in the ceiling.
Note: Wood screws are supplied with your xture; however, dierent materials and/or construction methods may
require dierent fasteners. If in doubt, contact a qualied electrician.
Caution: Do not rely on anchors alone to suspend xture. Fixture must be attached to a structural member in the
ceiling.
7. Install screws (C) into remaining holes with anchors (D). Be sure not to overtighen and strip the anchor (D).
8. Remove nuts (H) from studs on canopy cover plate (B) and retain for use in next step.
9. Raise canopy cover plate (B). Slide end of safety cables (G) over studs and reattach nuts (H). Safety cables (G) are
used to temporarily suspend canopy cover plate (B) while connections are made.
10. Attach a pigtail lead to canopy (A) using ground screw (E) and cupped washer (F), found in kit bag.
11. Using suitable wire connectors (not provided) connect transformer wires to supply wires (white to white and black to
black). Connect all ground wires (bare copper or green to bare copper or green) together.
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY, AND NO BARE WIRE IS EXPOSED.
12. Continue steps on following pages to complete xture wiring.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49669 Rev A
3 OF 8
ASSEMBLY & INSTALLATION INSTRUCTIONS
Link Multiport Round 9lt Pendants 131100 & 131108
A774
D
A
I
F
E
C
G
H
B
N
(Figure 1)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49669 Rev A
4 OF 8
ASSEMBLY & INSTALLATION INSTRUCTIONS
A774
Link Multiport Round 9lt Pendants 131100 & 131108
To Install Fixtures (Figures 2 & 3 - on following pages)
1. Unpack xtures (O).
2. Twist together wires and slide through gripper (J) in canopy cover plate (B).
Note: It maybe helpful to depress the gripper plunger to help wires pass through gripper.
3. Repeat for remaining xtures (O) and grippers (J).
4. Reference Figure 3 - Wiring Diagram on page 7 for the following steps:
5. Wire connectors (M) and jumper wires have been attached to red transformer (L) wires to aid in wiring installation.
6. Using provided wire connectors (M) and black jumper wires, connect Stranded xture wires to eachother and then to
wire connector (M) attached to the red transformer (L) wire. Wires should be stripped 3/8” maximum.
7. Following same sequence again from Figure 3; using provided wire connectors (M) and white jumper wires, connect
Braided xture wires to eachother and then to the wire connector (M) attached to the red transformer (L) wire.
8. Align holes in canopy cover plate (B) with studs (I) in canopy (A). Raise canopy cover plate (B) and xtures (O) to
canopy (A).
9. Secure canopy cover plate (B) by threading caps (N) onto studs (I).
CAUTION: BE SURE NO WIRES ARE PINCHED BETWEEN THE CANOPY (A) AND COVER PLATE (B).
10. Push supply/support cable (K) into gripper (J) until desired height is reached.
11. If cable needs to be pulled from canopy, push up on gripper (J) plunger while gently pulling on supply/support cable
(K) to adjust length.
12. Repeat for remaining xtures (O).
13. Follow instructions on following page to install glass.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49669 Rev A
5 OF 8
ASSEMBLY & INSTALLATION INSTRUCTIONS
Link Multiport Round 9lt Pendants 131100 & 131108
A774
A
G
J
B
L
N
K
O
(Figure 2)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49669 Rev A
6 OF 8
ASSEMBLY & INSTALLATION INSTRUCTIONS
Link Multiport Round 9lt Pendants 131100 & 131108
A774
M
Stranded Wire
Fixture
Wires
L
Transformer
Wire
Braided Wire
Wire Diagram Used for Stranded
and Braided Fixture (O) Wires.
(Figure 3)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49669 Rev A
7 OF 8
ASSEMBLY & INSTALLATION INSTRUCTIONS
Link Multiport Round 9lt Pendants 131100 & 131108
To Install Bulbs & Glass (Figure 4)
1. Install bulb (Q) (not included) into socket (P).
2. Loosen four screws (S).
Note: It is not necessary to remove screws from the
xture (O).
3. Raise glass (R) until groove is aligned with screws (S).
4. Tighten screws (S) equally until snug against glass (R).
Note: Be careful not to over tighten as this could break
glass (R).
5. Repeat for remaining bulbs (Q) and glass (R).
A774
O
P
6. Restore electricity at the main breaker.
S
Q
GROOVE
R
(Figure 4)
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49669 Rev A
8 OF 8
Loading...