ASSEMBLY & INSTALLATION INSTRUCTIONS
Orion 1-Pipe Triple Pendant 136437
A806
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
50425
1 OF 4
ASSEMBLY & INSTALLATION INSTRUCTIONS
Orion 1-Pipe Triple Pendant 136437
Component Parts
A Fixture
B Crossbar
C Jam Nut
D Threaded Nipple
E Ground Screw
F Canopy Ring
G Canopy
A806
H Swivel
I 3" Fixture Pipe (1)
J 6" Fixture Pipe (1)
K 12" Fixture Pipe (3)
L Stem Nipple (5)
M Socket (2)
N Bulb (not included)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
50425
2 OF 4
ASSEMBLY & INSTALLATION INSTRUCTIONS
A806
Orion 1-Pipe Triple Pendant 136437
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products and options.
To Install Fixture (Figure 1) on following page
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
1. Carefully unpack xture (A) from the carton.
2. Frame (P) is shipped installed on xture (A), remove frame (P) by loosening binding screws (R) and binding nuts (Q)
and set aside for use in installing glass.
3. Thread jam nut (C) and crossbar (B) onto threaded nipple (D) with ground screw (E) facing towards swivel (HI); leave
both parts loose.
4. Using two machine screws (not provided), temporarily fasten crossbar (B) to the electric box.
NOTE: A NEW ELECTRIC BOX COMES WITH SCREWS. WHEN REPLACING A FIXTURE, RETAIN THE EXISTING
SCREWS FOR USE WITH THE NEW FIXTURE.
5. Adjust the length of threaded nipple (D) in crossbar (B) so that canopy ring (F) will hold canopy (G) against the ceiling
with no threads showing for best appearance. When the correct adjustment is established, tighten jam nut (C) against
crossbar (B) to secure the adjustment.
6. Remove crossbar (B) from the electrical box and proceed with the assembly instructions.
7. Locate fixture pipes (I, J, K), fixture (A), stem nipples (L) . Stem nipples (L) can be found in the kit bag.
8. Provided are multiple fixture pipes in three different lengths. Choose the combination that will achieve the overall
height desired. Refer to the table below to determine the pipes required to reach the desired overall height. Once you
have determined the components necessary, feed the wires that exit fixture (A) through the individual components and
thread pipes and nipples together. Wires will slip easier through loose components than through pipes and nipples that
are pre-assembled. Once wires are run, apply thread locking compound to all the connection points and assemble the
pipes and nipples.
NOTE: APPLICATION OF THE THREAD LOCKING COMPOUND IS NECESSARY TO PREVENT THE PIPE FROM
LOOSENING DURING REGULAR MAINTENANCE AND CLEANING OF THE FIXTURE. BE CERTAIN TO APPLY THE
COMPOUND.
9. Carefully slide canopy ring (F) and canopy (G) over wires and fixture pipes (I, J, K) until they rest on fixture (A).
10. Slip wires from the xture (A) through assembled swivel (H) and threaded nipple (D).
11. Refer to instructions on next page to continue installation.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
50425
3 OF 4
ASSEMBLY & INSTALLATION INSTRUCTIONS
Orion 1-Pipe Triple Pendant 136437
12. Using two machine screws (not provided), fasten crossbar (B)
to the electric box.
A806
13. Using suitable wire connectors (not provided) connect fixture
wires to supply (white/ribbed to white and black/smooth to
black). Attach a pigtail lead to crossbar ground screw (E). Hold
canopy (G) close, connect all ground wires (bare copper or
green to bare copper or green).
CAUTION: MAKE SURE WIRE CONNECTORS ARE
TWISTED ON SECURELY, AND NO BARE WIRE IS
EXPOSED.
14. Slide canopy (G) against ceiling, and secure with canopy ring
(F).
CAUTION: BE SURE NO WIRES ARE PINCHED
BETWEEN CANOPY (H) AND THE CEILING.
15. Install bulbs (N) (not included) into sockets (M).
16. Restore electricity at main breaker.
B
E
MACHINE
SCREWS
C
D
H
G
F
I
L
J
L
K
L
K
K
(Figure 1)
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.
L
L
A
M
N
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
50425
4 OF 4
Loading...