ASSEMBLY & INSTALLATION INSTRUCTIONS
Aura Pendant 138588
A771
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49644
1 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Aura Pendant 138588
Component Parts
A Canopy
B Canopy Cover Plate
C Cap
D Nut
E Lag Screw (4)
F Fixture
G Gripper (4)
H Supply/Support Cable (4)
A771
I #8 Screws (2)
J Flat Head Screw (6)
K Bulb Cover assembly (6)
L Bulb (supplied) (6)
M Socket (6)
N Glass (6)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49644
2 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Aura Pendant 138588
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products and options.
To Install Canopy (Figure 1)
CAUTION: BE SURE POWER IS OFF AT THE MAIN
BREAKER BOX PRIOR TO INSTALLATION.
1. Carefully unpack the xture from the carton.
2. Locate canopy assembly (A). Remove cap (C) and
canopy cover plate (B) and set aside for use later.
3. To attach canopy (A) directly to the junction box: Thread
the wires in the electrical box through the hole in the
canopy (A) while moving the canopy into position. Using
two machine screws (not provided) fasten canopy (A) to
the electric box.
4. Using the four lag screws (E) secure canopy (A) to a structural member in the ceiling. We've supplied lag screws
(E) with your xture; however, dierent materials and/or
construction methods may require dierent fasteners. If in
doubt, contact a qualied electrician.
Note: A new electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new fixture.
A
I
E
MACHINE
SCREW
G
A771
5. Remove nut (D) from stud on canopy cover plate (B).
Slide end of safety cable over stud and reattach nut (D).
The safety cable also acts as ground for the canopy cover
plate (B)
6. Using suitable wire connectors (not provided) connect
transformer wires to supply wires (white to white and black
to black). Connect all ground wires (bare copper or green
to bare copper or green) together
7. To secure gripper plate use the supplied #8 screws into
matching standos.
8. Reinstall canopy cover plate (B) making sure the (+) and
(-) labels on the cover are aligned with the labels on the
canopy (A). Secure in place with cap (C).
CAUTION: MAKE SURE WIRE CONNECTORS ARE
TWISTED ON SECURELY, AND NO BARE WIRE IS
EXPOSED.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
(Figure 1)
SAFETY CABLE
D
STUD
B
C
49644
3 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Aura Pendant 138588
To Complete Installation (Figure 3)
1. Align (+) and (-) labels on xture (F)with (+)
and (-) labels on canopy.
2. Insert cable (H) into gripper (G) until cable
sticks through the slot in the side of the
gripper (G).
3. Repeat with remaining cables (H).
A771
SLOT
4. Continue pulling cables (H) through
grippers (G) until correct xture
height is achieved. Adjust height
of xture (F), making sure to keep xture
level.
Note: If fixture needs to be lowered,
push up on the gripper plunger to
release cable.
5. Once desired height of the xture (F) is
achieved, cut o the excess cable (H) as
close to the gripper (G) as possible.
CAUTION: BE SURE THAT NO PIECE OF
THE SUPPORT CABLE IS TOUCHING THE
FIXTURE
CAUTION: ONCE EXCESS CABLE IS CUT,
FIXTURE CANNOT BE LOWERED
G
H
F
(Figure 2)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49644
4 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Aura Pendant 138588
To Install Bulb & Glass (Figure 3 & Figure 4)
1. Loosen at head screw (J) and slip bulb cover assembly (K)
from xture. (Figure 3)
A771
2. Install bulb (L) (supplied).
3. Install bulb cover assembly (K) and tighten at head screw
(J).
4. Repeat steps for all bulb locations.
5. Slip glass (N) into slots in xture between bulb locations.
(Figure 4)
6. Repeat for all remaining glass.
7. Restore electricity at the main breaker.
J
M
K
L
(Figure 3)
N
(Figure 4)
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.
We hope you enjoy your xture! * Vermont Modern / Hubbardton Forge will not be liable for injury or damage caused by improper
installation, lamping or use of this xture.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49644
5 OF 5
Loading...