ASSEMBLY & INSTALLATION INSTRUCTIONS
Tura Low Voltage Pendant 161184
A842
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49683
1 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Tura Low Voltage Pendant 161184
Component Parts
A Crossbar
B Cupped Washer
C Ground Screw
D Canopy
E #8 Screws (2)
F Canopy Gripper
A842
G Supply/Support Cable
H Fixture
I Screws with Lock Washer (2)
J Canopy Plate
K Bulb (not included)
L Socket
M Collar
N Cage Assembly
O Glass
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49683
2 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Tura Low Voltage Pendant 161184
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products and options.
To Attach to Ceiling (Figures 1 & 2)
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
1. Carefully unpack xture from the carton.
2. Crossbar (A) and canopy (D) ship assembled. Remove (2) #8 screws (E) to separate the canopy from the crossbar.
Retain parts for later use.
3. Using two machine screws (not provided), fasten the crossbar (A) to the electric box.
Note: A new electric box comes with screws. When replacing a fixture, retain the existing screws for use with
the new fixture.
A842
4. Height of xture can be set before attaching the xture to the ceiling. Remove screws with lock washers (I) and
canopy plate (J) from canopy (D). If height is going to stay at max length or just a slight height adjustment is needed
it may not be necessary to remove the canopy plate.
Note: Fixture is shipped at max height
5. Push supply/support cable (G) into canopy gripper (F) until desired height is reached. If cable needs to be pulled
from canopy, push in on canopy gripper (F) plunger while pulling on supply/support cable (G) to adjust length.
6. Coil supply/support cable (G) in canopy (D) and place canopy plate (J) in canopy. Install screws w/lock washers (I)
to secure plate.
Caution: Be sure not to pinch wires between canopy and plate
I
J
F
D
(Figure 1)
G
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49683
3 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
A842
Tura Low Voltage Pendant 161184
7. Attach a pigtail lead to crossbar using ground screw (C) and the cupped washer (B). Raise canopy (D) close to ceiling.
Using suitable wire connectors (not provided) connect xture wires to supply wires (white to white, black to black).
Connect all ground wires (bare copper or green to bare copper or green). Figure 2
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY AND NO BARE WIRE IS EXPOSED.
8. Align holes in canopy (D) with holes in crossbar (A) and secure with (2) #8 screws (E).
CAUTION: BE SURE NO WIRES ARE PINCHED BETWEEN THE CANOPY (D) AND THE CEILING.
9. If xture height needs to be adjusted to achieve desired height, push up on canopy gripper (F) and gently pull down/
push up on supply/support cable (G).
10. Follow instructions on following page to install glass.
A
MACHINE
SCREWS
B
C
D
E
F
G
H
(Figure 2)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49683
4 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Tura Low Voltage Pendant 161184
To Install Glass (Figure 3)
1. Install bulb (K), not included, into socket (L).
2. Carefully unpack cage assembly (N) and
glass (O).
A842
G
3. Slide cage assembly (N) over nozzle and up
supply/support cable (G).
4. Thread glass (O) onto collar (M) and up to
nozzle.
5. Lower cage assembly (N) until it rests on top
of glass (O).
Note: Nozzle will help center cage assembly (N) on glass (O).
6. Restore electricity at the main breaker
N
NOZZLE
M
L
K
O
(Figure 3)
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49683
5 OF 5
Loading...