ASSEMBLY & INSTALLATION INSTRUCTIONS
Eos 3 Light Bath Sconce 201332
B479
49611
1 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Eos 3 Light Bath Sconce 201332
Component Parts
A. Fixture
B. Mounting Bracket
C. Ground Screw
D. Cupped Washer
E. #8 Screws (4)
F. Socket (3)
G. Bulb (Not Included)
H. Glass (3)
B479
I. Thumb Screw(6)
J. Anchor (4)
K. #10 Screw (4)
49611
2 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
B479
Eos 3 Light Bath Sconce 201332
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products.
To Install Fixture (Figure 1, on next page)
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
1. Carefully unpack the xture (A) from the carton.
2. Remove mounting bracket (B) from xture (A).
3. Place the mounting bracket (B) over the electrical box being sure to hold it level. Line up holes in
mounting bracket with holes in electrical box.
4. With a pencil, mark the location of at least 2 additional mounting hole locations in the mounting bracket (B) on the wall
behind. Set bracket aside.
5. Drill 1/4" holes in the locations marked on the wall. Place the tapered end of the anchors (J) into the holes and
gently tap them ush to the wall using a light weight hammer.
6. Thread the wires in the electrical box through the hole in the mounting bracket (B) while moving the bracket into
position. Using (2) machine screws (not included), fasten bracket (B) to the box.Using #10 screws (K), screw the
mounting bracket securely to the wall. Be careful not to over-tighten or strip the anchors (J).
Note: A new electric box comes with screws. When replacing a fixture, retain the existing screws for use.
7. Attach a pigtail lead to the mounting bracket (B) using the ground screw (C) and cupped washer (D) found in kit bag.
8. Hold xture (A) close to wall. Using suitable wire connectors (not provided), connect xture wires to supply wires
(white to white and black to black). Connect all ground wires (bare copper or green to bare copper or green).
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY, AND NO BARE WIRE IS EXPOSED.
9. Place xture (A) over mounting bracket (B) secure with #8 screws (E) on top and bottom of xture. Be sure no wires
are pinched between xture and wall.
10. Follow steps on page 5 to complete installation.
49611
3 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Eos 3 Light Bath Sconce 201332
B479
E
J
B
K
D
C
MACHINE
SCREWS
A
(Figure 1)
49611
ASSEMBLY & INSTALLATION INSTRUCTIONS
Eos 3 Light Bath Sconce 201332
To Install Glass (Figure 2)
1. Install bulb (G) (not included) into socket (F).
2. Thumb screw (I) is shipped installed remove and set asside for
use in the next step.
3. Carefully unpack glass (H), slide over socket (F) and secure
with thumb screw (I).
Note: Be sure not to over tighten as this
could break the glass.
4. Restore electricity at main breaker.
B479
I
F
G
(Figure 2)
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this
xture.
H
49611
5 OF 5
Loading...