ASSEMBLY & INSTALLATION INSTRUCTIONS
Brooklyn Straight Double Shade 3 Light Sconce 201378
B469
49109
1 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Brooklyn Straight Double Shade 3 Light Sconce 201378
Component Parts
A Fixture
B Mounting Bracket
C Ground Screw
D Cupped Washer
E # 8 Screws (4)
B469
F Nut (6)
G Collar (3)
H Accent Shade (6)
I Socket (3)
J Bulb (not included)
K Glass (3)
L # 10 Screws (4)
M Anchors (4)
49109
2 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
B469
Brooklyn Straight Double Shade 3 Light Sconce 201378
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products.
To Install Fixture (Figure 1) on following page
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
1. Carefully unpack the xture (A) from the carton.
2. Take o rubber band and remove mounting bracket (B) from xture (A).
3. Place the mounting bracket (B) over the electrical box being sure to hold it level. Line up holes in mounting bracket
with holes in electrical box. With a pencil, mark the location of all mounting holes in the mounting bracket on the wall
behind. Set bracket aside.
4. Drill 1/4" holes in the locations marked on the wall. Place the tapered end of the anchors (M) into the holes and gently
tap them ush to the wall using a light weight hammer.
5. Thread the wires in the electrical box through the hole in the mounting bracket (B) while moving the bracket into
position. Using (2) screws (not provided), attach the mounting bracket securely to the junction box.
Note: A new electric box comes with screws. When replacing an existing xture, retain screws for use with the new
xture
6. Using #10 screws (L), screw the bracket securely to the wall. Be careful not to over-tighten or strip the anchors (M).
7. Using suitable wire connectors (not provided) connect fixture wires to supply (white to white and black to black).
Attach a pigtail lead to bracket using ground screw (C) and cupped washer (D) found in kit bag. Connect all ground
wires (bare copper or green to bare copper or green).
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON
SECURELY, AND NO BARE WIRE IS EXPOSED.
8. Carefully tuck all wires behind xture, push xture rmly against the wall. Secure by threading # 8 screws (E) through
the holes on the top and bottom of the xture (A) into bracket (B).
Note: Be sure no wires are pinched between the wall and the fixture.
9. See instructions on the next page for installing accent shade and glass.
49109
3 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Brooklyn Straight Double Shade 3 Light Sconce 201378
B469
E
E
MACHINE
SCREWS
A
(Figure 1)
C
D
L
B
M
EE
49109
ASSEMBLY & INSTALLATION INSTRUCTIONS
B469
Brooklyn Straight Double Shade 3 Light Sconce 201378
To Install Shades & Glass (Figure 2)
1. Nuts (F) are shipped installed on collar (G). Remove and retain for next steps.
2. Slide accent shade (H) over collar (G) and up against nozzle. Rotate to desired location. Thread nut (F) onto collar
(G) to secure shade (H).
3. Slide second accent shade (H) over collar (G) and up against nut (F). Rotate to desired location. Thread nut (F) onto
collar (G) to secure second shade (H).
4. Install bulb (J), not included, into socket (I).
5. Carefully unpack glass (K) and thread onto collar (G).
6. Repeat for remaining shades (H) and glass (K).
7. Restore electricity at the main breaker
NOZZLE
G
I
H
F
H
F
J
(Figure 2)
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you
enjoy your xture!
K
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.
49109
5 OF 5
Loading...