ASSEMBLY & INSTALLATION INSTRUCTIONS
Eos Pendant/Semi-Flush 131062
A761
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49229
1 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Eos Pendant/Semi-Flush 131062
Component Parts
A Fixture
B Stem Adapter (2)
C Crossbar
D Jam Nut
E Threaded Nipple
F Ground Screw
G Canopy Ring
A761
H Canopy
I Swivel
J 3" Fixture Pipe (1)
K 6" Fixture Pipe (1)
L 12" Fixture Pipe (2)
M Stem Couplings (4)
N Socket (4)
O Bulb (not included)
P Thumb Screw (8)
Q Glass (4)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49229
2 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Eos Pendant/Semi-Flush 131062
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products and options.
To Install Fixture (Figure 1) on following page
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
1. Carefully unpack xture (A) from the carton.
2. Thread jam nut (D) and crossbar (C) onto threaded nipple (E) with ground screw (F) facing towards swivel (I); leave
both parts loose.
3. Using two machine screws (not provided), temporarily fasten crossbar (C) to the electric box.
NOTE: A NEW ELECTRIC BOX COMES WITH SCREWS. WHEN REPLACING A FIXTURE, RETAIN THE EXISTING
SCREWS FOR USE WITH THE NEW FIXTURE.
A761
4. Adjust the length of threaded nipple (E) in crossbar (C) so that canopy ring (G) will hold canopy (H) against the ceiling
with no threads showing for best appearance. When the correct adjustment is established, tighten jam nut (D) against
crossbar (C) to secure the adjustment.
5. Remove crossbar (C) from the electrical box and proceed with the assembly instructions.
6. Locate fixture pipes (J, K, L), fixture (A), stem coupling (M) and stem end (N). Stem couplings (M) and one stem
adapter (B) can be found in the kit bag.
7. Provided are multiple fixture pipes in three different lengths. Choose the combination that will acheive the overall
height desired. Refer to the table below to determine the pipes required to reach the desired overall height. Once you
have determined the components necessary, feed the wires that exit fixture (A) through stem adapter (B) through the
individual components and thread pipes and couplings together. Wires will slip easier through loose components than
through pipes and couplings that are pre-assembled. Once wires are run, apply thread locking compound to all the
connection points and assemble the pipes and nipples.
NOTE: APPLICATION OF THE THREAD LOCKING COMPOUND IS NECESSARY TO PREVENT THE PIPE FROM
LOOSENING DURING REGULAR MAINTENANCE AND CLEANING OF THE FIXTURE. BE CERTAIN TO APPLY THE
COMPOUND.
8. Carefully slide canopy ring (G) and canopy (H) over wires and fixture pipes (J, K, L) until they rest on fixture (A).
9. Slip wires from the xture (A) through assembled swivel (I) and thread swivel into stem adapter (B).
10. Refer to instructions on next page to continue installation.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49229
3 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Eos Pendant/Semi-Flush 131062
11. Using two machine screws (not provided), fasten crossbar (C)
to the electric box.
A761
12. Using suitable wire connectors (not provided) connect fixture
wires to supply (white/ribbed to white and black/smooth to
black). Attach a pigtail lead to crossbar ground screw (F). Hold
canopy (H) close, connect all ground wires (bare copper or
green to bare copper or green).
CAUTION: MAKE SURE WIRE CONNECTORS ARE
TWISTED ON SECURELY, AND NO BARE WIRE IS
EXPOSED.
13. Slide canopy (H) against ceiling, and secure with canopy ring
(G).
CAUTION: BE SURE NO WIRES ARE PINCHED
BETWEEN CANOPY (H) AND THE CEILING.
14. Refer to instructions on next page to Install Glass.
C
MACHINE
SCREWS
E
H
J
K
L
F
D
I
G
B
M
L
(Figure 1)
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.
M
M
B
A
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49229
4 OF 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Eos Pendant/Semi-Flush 131062
To Install Glass (Figure 2)
1. Install bulb (O) (not included) into socket (N).
2. Thumb screw (P) is shipped installed remove
and set asside for use in the next step.
3. Carefully unpack glass (H), slide over socket
(N) and secure with thumb screw (P).
Note: Be sure not to over tighten as this
could break the glass.
4. Repeat for remaining glass.
5. Restore electricity at main breaker.
A761
(Figure 2)
Q
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
P
N
O
49229
5 OF 5
Loading...