ASSEMBLY & INSTALLATION INSTRUCTIONS
Gatsby Chandelier Simplified 105021
A770
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49662
1 OF 7
1
ASSEMBLY & INSTALLATION INSTRUCTIONS
Gatsby Chandelier Simplified 105021
Component Parts
A770
A Fixture
B Can
C Pipe (2)
D Lock Washer (2)
E Hex Nut (2)
F Pipe Hook (2)
G Pipe Loop (2)
H Cover Plate
I Fixture Nipple
J Fixture Loop
K Crossbar
L Canopy Nipple
V Socket Cup (8)
W Washer (8)
X Crystal (8)
Y Socket (8)
Z Bulb (8) - Not Included
M Lag Screw (2)
N Lock Nut
O Canopy
P Loop Collar
Q Canopy Loop
R Chain
S Ground Screw
T Cupped Washer
U Ground Nut
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49662
2 OF 7
ASSEMBLY & INSTALLATION INSTRUCTIONS
A770
Gatsby Chandelier Simplified 105021
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products and options.
To Assemble Fixture (Figures 1 & 2 - on following page)
1. Carefully unpack xture (A) from the carton.
2. Locate pipes (C). Lock washers (D) and hex nuts (E) are shipped attached on pipes. Remove and retain for later
step.
3. Fixture loop (J) and cover plate (H) are shipped installed. Unthread loop (J) and slide both loop (J) and cover plate
(H) on wires to access can (B).
4. Raise can (B) up and install pipe (C) into hole until half ball rests on can (B). Place lock washer (D) over end of pipe
(C) and secure with hex nut (E).
5. Install pipe hook (F) on end of pipe (C) into pipe loop (G). It may be necessary to loosen hex nuts (E) slightly to allow
hook (F) to install into loop (G).
6. Repeat with remaining pipe (C). Once pipes (C) are installed and hooks (F) are attached to pipe loops (F), tighten all
hex nuts (E) completely.
7. Place cover plate (H) over xture nipple (I). Secure with xture loop (J).
CAUTION: BE SURE NO WIRES ARE PINCHED BETWEEN COVER PLATE (H) AND CAN (B).
8. Follow steps on remaining pages to complete xture install.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49662
3 OF 7
ASSEMBLY & INSTALLATION INSTRUCTIONS
Gatsby Chandelier Simplified 105021
A770
J
H
E
D
I
B
HALF BALL
C
A
(Figure 1)
(Figure 2)
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
F
G
49662
4 OF 7
ASSEMBLY & INSTALLATION INSTRUCTIONS
A770
Gatsby Chandelier Simplified 105021
To Attach to Ceiling (Figure 3 - on following page)
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
1. Drill two holes through the back of the outlet box and using two lag screws (M), attach crossbar (K) to a solid structural
member in the ceiling, centering the crossbar in the outlet box.
Lag screws are supplied with your xture; however, dierent materials and/or construction methods may require dierent fasteners. If in doubt, contact a qualied electrician.
2. Thread canopy loop (Q) onto canopy nipple (L). Place canopy (O) over loop and adjust nipple length to ensure a snug
canopy t using loop collar (P). Once the length is determined, set the canopy and loop collar aside and lock canopy
nipple position by tightening the lock nut (N) against the crossbar (K).
3. Attach one end of the chain (R) to xture loop (J).
4. Slide loop collar (P) and canopy (O) over chain (R) and xture wires until they rest on xture loop (J). Thread the x-
ture wires through every other link of the chain (R). Attach the other end of the chain to the canopy loop (Q).
5. Run wires up through the canopy loop (Q) and canopy nipple (L) into the outlet box.
6. Using suitable wire connectors (not provided), connect xture wires to supply wires (ribbed side of xture cord to white
supply, smooth side of xture cord to black supply). Run a pigtail lead from the ground screw (S), cupped washer
(T) and ground nut (U) on crossbar (K) and connect all ground wires (bare copper or green to bare copper or green)
together. Push wires back into outlet box.
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY AND NO BARE WIRE IS EXPOSED.
7. Slide the canopy (O) up the chain (R) and over the canopy loop (Q). Holding tight to the ceiling, secure with loop collar (P).
CAUTION: BE SURE NO WIRES ARE PINCHED BETWEEN THE CANOPY (O) AND THE CEILING.
8. Follow remaining steps to install crystals.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49662
5 OF 7
ASSEMBLY & INSTALLATION INSTRUCTIONS
Gatsby Chandelier Simplified 105021
A770
K
S
T
U
M
Q
R
L
N
O
P
(Figure 3)
J
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49662
6 OF 7
ASSEMBLY & INSTALLATION INSTRUCTIONS
Gatsby Chandelier Simplified 105021
To Install Crystals (Figure 4)
1. Locate the crystals (X) and white gloves.
Note: Using white gloves while handling the crystals (X)
will prevent smudges.
A770
2. Place crystal (X), smaller hole rst, over socket cup (V)
until it rests on washer (W). Crystal can be rotated on
socket cup to desired orientation.
3. If needed, use the provided white gloves to polish the
crystals (X).
4. Install bulb (Z), not included, into socket (Y).
5. Repeat steps 2 thru 4 for remaining crystals (X) and
sockets (Y).
6. Restore electricity at the main breaker.
Z
X
Y
V
W
(Figure 4)
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of
this xture.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
49662
7 OF 7
Loading...