Hubbardton Forge GCVP1454 Installation & Assembly

Page 1
ASSEMBLY & INSTALLATION INSTRUCTIONS
Henry Post Light 344227
G24
45330
1 OF 5
Page 2
ASSEMBLY & INSTALLATION INSTRUCTIONS
Henry Post Light 344227
Component Parts
A J Bolt
B Post
D Split Washer (4)
E Hex Nut (4)
F Cover Cap (optional)
G Set Screw
G24
H Fixture
I Rubber Pad (4)
J Glass
K Thumb Screws (4)
L Metal Shade
45330
2 OF 5
Page 3
ASSEMBLY & INSTALLATION INSTRUCTIONS
Henry Post Light 344227
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be
installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.* Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products.
To Install (Figure 1)
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
NOTE: Fixture, Post and Cover Cap each sold separately.
SITE PREPERATION:
1. Run appropriate wiring to the site of the xture, leaving enough excess wire to reach the top of the post, plus 12 inches.
G24
2. Pour at and level concrete base with wiring emerging at the center. Insert J bolts (A) so approximately 1" of the bolts are exposed above the concrete. Position J bolts according to the template on the last page of these instructions. Allow concrete to cure before installing xture.
INSTALLATION:
NOTE: Post may be cut to desired height before installation.
3. Position post (B) over J bolts (A), feeding supply wire up though the post and secure using at washers (C), split washers (D) and hex nuts (E).
4. Place optional cover cap (sold separately) (F) over post (B) to conceal mounting hardware.
5. Attach the four rubber pads (I) to the inside of xture (H).
6. Connect xture wires to supply wires using appropriate wire connectors
(not provided), black to black (or smooth), white to white (or ribbed) and bare copper or green to bare copper or green.
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY AND NO BARE WIRE IS EXPOSED.
7. Place xture (H) onto post (B), carefully tucking all wiring down into post and making sure no wires are pinched between the post and the xture. Secure with set screw (G).
8. Follow steps on next page to install glass.
H
G
I
B
F
E
D
C
(Figure 1)
A
45330
3 OF 5
Page 4
ASSEMBLY & INSTALLATION INSTRUCTIONS
G24
Henry Post Light 344227
To Install Glass (Figure 2)
1. Unpack glass (J).
2. Install bulb (not included) into socket.
3. Slide glass (J) over bulb until it rest on xture (H).
4. Remove thumb screws (K) from fixture (H).
5. Place metal shade (L) onto fixture (H), aligning the holes with the fixture arms.
6. Install thumb screws (K) to hold shade (L). For ease of installation, make sure all screws (K) are started before tight-
ening fully.
NOTE: It may be necessary to flex the fixture arms so all shade holes line up with threaded holes in fixture arms.
7. Restore electricity at main breaker.
J
ARM
BULB
K
L
(Figure 2)
H
45330
Page 5
ASSEMBLY & INSTALLATION INSTRUCTIONS
Henry Post Light 344227
USE THIS TEMPLATE TO POSITION J BOLTS AND WIREWAY IN CONCRETE SLAB PRIOR TO INSTALLING OUTDOOR POST MOUNTED LIGHTING FIXTURE.
G24
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of
this xture.
45330
5 OF 5
Loading...