Page 1
ASSEMBLY & INSTALLATION INSTRUCTIONS
Vela Sconce 203330
B392
42338
1 OF 4
Page 2
ASSEMBLY & INSTALLATION INSTRUCTIONS
Vela Sconce 203330
Component Parts
A Fixture
B Mounting Bracket
C Anchors (4)
D #10 Scews (4)
E Ground Screw
F Cupped Washer
G #8 Screws (4)
H Socket
B392
I B Type Bulb (Not Included)
J Glass
K O-Ring
L Socket Cup
42338
2 OF 4
Page 3
ASSEMBLY & INSTALLATION INSTRUCTIONS
Vela Sconce 203330
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND
PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products.
To Install Fixture (Figure 1)
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
1. Carefully unpack the xture (A) from the carton.
2. Take off rubber band and remove mounting bracket
(B) from xture (A).
3. Place the mounting bracket (B) over the electrical
box being sure to hold it level. Line up holes in
mounting bracket with holes in electrical box. With
a pencil, mark the location of all mounting holes
in the mounting bracket on the wall behind. Set
bracket aside.
B392
4. Drill 1/4" holes in the locations marked on the wall.
Place the tapered end of the anchors (C) into the
holes and gently tap them ush to the wall using a
light weight hammer.
5. Thread the wires in the electrical box through the
hole in the mounting bracket (B) while moving the
bracket into position. Using #10 screws (D), screw
the mounting bracket securely to the wall. Be careful
not to over-tighten or strip the anchors (C).
6. Attach a pigtail lead to the mounting bracket (B)
using the ground screw (E) and cupped washer (F)
found in kit bag.
7. Hold xture (A) close to wall. Using suitable wire
connectors (not provided), connect xture wires to
supply wires (white to white and black to black).
Connect all ground wires (bare copper or green to
bare copper or green).
CAUTION: MAKE SURE WIRE CONNECTORS ARE
TWISTED ON SECURELY, AND NO BARE WIRE IS
EXPOSED.
8. Place xture (A) over mounting bracket (B). Secure
with #8 screws (G) on top and bottom of xture. Be
sure no wires are pinched between xture and wall.
9. See following page to complete installation.
B
C
F
E
D
A
G
(Figure 1)
42338
3 OF 4
Page 4
ASSEMBLY & INSTALLATION INSTRUCTIONS
Vela Sconce 203330
To Install Glass (Figure 2)
1. Unpack glass (J) and locate o-ring (K), found in kit bag.
2. Stretch o-ring (K) over one end of glass (J). Leave just slightly
up from bottom of glass (See gure 2).
3. Install B type bulb (I) (not included) into socket (H) .
4. Place glass (J) over the B type bulb.
5. Slide glass (J) and o-ring (K) into socket cup (L) until it hits
bottom of cup.
Note: Be sure o-ring slides into cup. It may be necessary
to rotate glass or push on o-ring to allow it to slide into cup
evenly.
6. Restore electricity at main breaker.
B392
J
K
(Figure 2)
I
H
L
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this
xture.
42338
4 OF 4
Loading...