Page 1
ASSEMBLY & INSTALLATION INSTRUCTIONS
Erlenmeyer Outdoor Lantern 356010
A571
42356 Rev A
1 OF 4
Page 2
ASSEMBLY & INSTALLATION INSTRUCTIONS
Erlenmeyer Outdoor Lantern 356010
Component Parts
A Crossbar
B Lock Nut
C Nipple
D Ground Screw
E Canopy
F Canopy Ring
A571
G Canopy Loop
H Chain
I Fixture Loop
J Fixture
K Socket
L Glass
M Ring
N Thumb Screws (4)
42356 Rev A
2 OF 4
Page 3
ASSEMBLY & INSTALLATION INSTRUCTIONS
Erlenmeyer Outdoor Lantern 356010
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must
be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation
of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.
Caution: Damp location outdoor hanging xtures are designed for use in covered spaces such as porches protected
from prolonged exposure to water and wind. If installing in locations subject to wind the use of supplementary chains,
cables, or similar restraints may be necessary to protect against swinging and twisting. If in doubt consult a qualied
installer.
Please Note: After installation, extra hardware and accessories are possible; our kits are used on multiple products.
To Install Fixture (Figure 1)
A571
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
1. Carefully unpack xture from the carton.
2. Using two machine screws (not provided), fasten the crossbar (A) to the
electric box with the head of the ground screw (D) facing down.
Note: A new electric box comes with screws. When replacing a fixture, retain
the existing screws for use with the new fixture.
3. Thread nipple (C) into crossbar (A) and then thread lock nut (B) and canopy
loop (G) onto threaded nipple, leaving parts loose. Adjust the length of threaded
nipple in crossbar (A) so that canopy ring (F), which comes threaded onto canopy loop (G), will hold canopy (E) against the ceiling with no threads showing for
best appearance. When the correct adjustment is established, tighten lock nut
against crossbar to hold adjustment.
4. Remove the crossbar (A) assembly from electrical box.
5. Attach one end of the chain (H) to the xture loop (I) using a chain spreader (not
provided). Lace the wires through every other link of the chain (H) to the end.
Slip wires and chain (H) through canopy ring (F) and canopy (E). Fasten the
chain to the canopy loop (G) using chain spreader.
6. Slip wires through the canopy loop (G) and nipple (C). Make sure to provide
enough slack in the wire to ensure weight of xture is supported by the chain.
7. Using two machine screws (not provided), reattach the crossbar (A) to the electric box.
A
D
B
C
G
E
F
H
I
8. Using suitable wire connectors (not provided) connect xture wires to
supply wires (white to ribbed side of the xture cord, black to smooth side).
Holding canopy (E) close to ceiling, run a pigtail lead from crossbar ground
screw (D) to the electric box and connect all ground wires (bare copper or green
to bare copper or green).
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON
SECURELY AND NO BARE WIRE IS EXPOSED.
9. Raise canopy (E) to the ceiling and secure loop collar (F) to canopy loop (G).
10. Follow steps on next page to install glass.
(Figure 1)
J
42356 Rev A
3 OF 4
Page 4
ASSEMBLY & INSTALLATION INSTRUCTIONS
Erlenmeyer Outdoor Lantern 356010
To Install Glass (Figure 2)
1. Unpack glass (L)
2. Install bulb (not included) into socket (K) .
3. Tilt glass (L), slip through bars on xture (J), over bulb and up into ring (M).
4. Align groove in glass (L) with thumb screws (N) in ring (M).
Note: It may be necessary to unthread thumb screws to allow glass to slide into ring. Thumb screws will not need to
be completely removed.
5. Tighten thumb screws (N) evenly into groove to secure glass (L) in xture (J).
Note: Be sure not to overtighten as this could break glass.
6. Restore electricity at main breaker.
A571
J
(Figure 2)
N
M
K
BULB
GROOVE
L
If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your xture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of
this xture.
42356 Rev A
4 OF 4
Loading...