Hubbardton Forge 366016 User Manual

Installation Instructions A103

g

For Chain-Hung Fixture 36-6016 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum watta

To Install Fixture (Figure 1)

Component Parts

A Lock Nut
B Crossbar
C Threaded Stud (2)
D Nipple
E Wood Screws (4)
F Canopy

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Thread studs (C) through appropriate holes in crossbar (B) to match holes

in canopy (F).

3. Thread the nipple (D) into the crossbar (B) and secure with lock nut (A).

4. Attach one end of the chain to the fixture loop (K). Lace the wire through

every other link of the chain (J) to the end.

5. Slide cover plate (H) and canopy (F) over chain (J) until they rest against

fixture top (L).

6. Fasten the chain to the canopy loop (G) and slip wires through the canopy

loop (G) and nipple (D). Make sure to provide enough slack in the wire
to ensure weight of fixture is supported by the chain.

7. Raise fixture to ceiling and using at least two wood screws (E) attach

cross bar (B) to a structural member in the ceiling, centering the crossbar
over the outlet box. We've supplied wood screws with your fixture;
however, different materials and/or construction methods may require
different fasteners. If in doubt, contact a qualified electrician. Do not
attach crossbar directly to outlet box.

8. Using suitable wire connectors (not provided) connect fixture wires to

supply wires (white to ribbed side of the fixture cord, black to smooth
side). Connect all ground wires to crossbar ground screw.

Caution: Make sure wire connectors are twisted on securely, and no
bare wire is exposed.

9. Slide canopy (F) and cover plate (H) over threaded studs (C) and push

firmly to ceiling, making sure that no wires are pinched between fixture
canopy and ceiling. Fasten with knurled balls (I). Be sure studs (C) are
fully seated in the knurled balls (I).

10. Install glass (see instructions on next page).

11. Restore electricity at main breaker.

e noted on fixture. Use only recommended bulbs with fixture.

G Canopy Loop
H Cover Plate
I Knurl Ball (2)
J Chain
K Fixture Loop
L Fixture Top

(Figure 1)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19774

Installation Instructions A103

(Fig

2

)

For Chain-Hung Fixture 36-6016 Page 2 of 2

To Install Glass (Figures 2, 3 & 4)

Component Parts

M Glass
N Glass Cage
O Retaining Ring
P Screws (3)
Q Socket

1. Install glass (M) in to glass cage (N) (Figure 2).

2. Place glass and cage (N) over socket (Q) (Figure 3).

3. Thread retaining ring (O) on to socket (Q) until snug against glass (M)

(Figure 3).

4. Rotate glass cage (N) to desired position. Install (3) screws (P) through

glass cage (N) into threaded bosses (Figure 4).

Caution: Retaining ring alone is not enough to hold glass permanently.

5. Install light bulb.

(Figure 3)

(Figure 4)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

ure

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19774